Re: [PATCH v2 1/2] drm/i915/bxt: Port PLL programming BUN

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On to, 2015-05-07 at 12:00 +0530, Vandana Kannan wrote:
> BUN 1: prop_coeff, int_coeff, tdctargetcnt programming updated and tied to
> VCO frequencies. Program i_lockthresh in PORT_PLL_9.
> 
> VCO calculated based on the formula:
> Desired Output = Port bit rate in MHz (DisplayPort HBR2 is 5400 MHz)
> Fast Clock = Desired Output / 2
> VCO = Fast Clock * P1 * P2
> 
> Prop_coeff, int_coeff, and tdctargetcnt modified according to above
> calculation.
> 
> BUN 2: Port PLLs require additional programming at certain frequencies -
> DCO amplitude in PORT_PLL_10
> 
> Review comments from Siva which were addressed in the initial version of the
> patch.
> 	- Change PORT_PLL_LOCK_THRESHOLD to PORT_PLL_LOCK_THRESHOLD_MASK
> 	- Calculate for HDMI
> 	- Correct values for vco = 5.4
> 	- return in case of invalid vco range
> 
> v2: Imre's review comments addressed
> 	- change dcoampovr_en to dcoampovr_en_h
> 	- change PORT_PLL_DCO_AMP_OVR_EN to PORT_PLL_DCO_AMP_OVR_EN_H
> 	- Correct lane stagger value for 324MHz
> 	- Make coef common for HDMI and DP
> 	- remove superfluous comments
> 
> Signed-off-by: Vandana Kannan <vandana.kannan@xxxxxxxxx>
> Reviewed-by: Sivakumar Thulasimani <sivakumar.thulasimani@xxxxxxxxx>
> Cc: Sivakumar Thulasimani <sivakumar.thulasimani@xxxxxxxxx>
> ---
>  drivers/gpu/drm/i915/i915_drv.h  |  2 +-
>  drivers/gpu/drm/i915/i915_reg.h  |  6 ++++
>  drivers/gpu/drm/i915/intel_ddi.c | 69 ++++++++++++++++++++++++++++++----------
>  3 files changed, 60 insertions(+), 17 deletions(-)
> 
> diff --git a/drivers/gpu/drm/i915/i915_drv.h b/drivers/gpu/drm/i915/i915_drv.h
> index 136d42a..05a4e1c 100644
> --- a/drivers/gpu/drm/i915/i915_drv.h
> +++ b/drivers/gpu/drm/i915/i915_drv.h
> @@ -304,7 +304,7 @@ struct intel_dpll_hw_state {
>  	uint32_t cfgcr1, cfgcr2;
>  
>  	/* bxt */
> -	uint32_t ebb0, pll0, pll1, pll2, pll3, pll6, pll8, pcsdw12;
> +	uint32_t ebb0, pll0, pll1, pll2, pll3, pll6, pll8, pll10, pcsdw12;
>  };
>  
>  struct intel_shared_dpll_config {
> diff --git a/drivers/gpu/drm/i915/i915_reg.h b/drivers/gpu/drm/i915/i915_reg.h
> index 1b31238..b086d26 100644
> --- a/drivers/gpu/drm/i915/i915_reg.h
> +++ b/drivers/gpu/drm/i915/i915_reg.h
> @@ -1185,6 +1185,12 @@ enum skl_disp_power_wells {
>  #define   PORT_PLL_GAIN_CTL(x)		((x)  << 16)
>  /* PORT_PLL_8_A */
>  #define   PORT_PLL_TARGET_CNT_MASK	0x3FF
> +/* PORT_PLL_9_A */
> +#define  PORT_PLL_LOCK_THRESHOLD_MASK	0xe
> +/* PORT_PLL_10_A */
> +#define  PORT_PLL_DCO_AMP_OVR_EN_H	(1<<27)
> +#define  PORT_PLL_DCO_AMP_MASK		0x3c00
> +#define  PORT_PLL_DCO_AMP(x)		(x<<10)
>  #define _PORT_PLL_BASE(port)		_PORT3(port, _PORT_PLL_0_A,	\
>  						_PORT_PLL_0_B,		\
>  						_PORT_PLL_0_C)
> diff --git a/drivers/gpu/drm/i915/intel_ddi.c b/drivers/gpu/drm/i915/intel_ddi.c
> index 9c1e74a..49b9fd8 100644
> --- a/drivers/gpu/drm/i915/intel_ddi.c
> +++ b/drivers/gpu/drm/i915/intel_ddi.c
> @@ -1337,18 +1337,20 @@ struct bxt_clk_div {
>  	uint32_t int_coef;
>  	uint32_t gain_ctl;
>  	uint32_t targ_cnt;
> +	uint32_t dcoampovr_en_h;
> +	uint32_t dco_amp;
>  	uint32_t lanestagger;
>  };
>  
>  /* pre-calculated values for DP linkrates */
>  static struct bxt_clk_div bxt_dp_clk_val[7] = {
> -	/* 162 */ {4, 2, 32, 1677722, 1, 1, 5, 11, 2, 9, 0xd},
> -	/* 270 */ {4, 1, 27,       0, 0, 1, 3,  8, 1, 9, 0xd},
> -	/* 540 */ {2, 1, 27,       0, 0, 1, 3,  8, 1, 9, 0x18},
> -	/* 216 */ {3, 2, 32, 1677722, 1, 1, 5, 11, 2, 9, 0xd},
> -	/* 243 */ {4, 1, 24, 1258291, 1, 1, 5, 11, 2, 9, 0xd},
> -	/* 324 */ {4, 1, 32, 1677722, 1, 1, 5, 11, 2, 9, 0xd},
> -	/* 432 */ {3, 1, 32, 1677722, 1, 1, 5, 11, 2, 9, 0x18}
> +	/* 162 */ {4, 2, 32, 1677722, 1, 1, 4, 9, 3, 8, 0, 15, 0xd},
> +	/* 270 */ {4, 1, 27,       0, 0, 1, 3,  8, 1, 9, 0, 15, 0xd},
> +	/* 540 */ {2, 1, 27,       0, 0, 1, 3,  8, 1, 9, 0, 15, 0x18},
> +	/* 216 */ {3, 2, 32, 1677722, 1, 1, 4, 9, 3, 8, 0, 15, 0xd},
> +	/* 243 */ {4, 1, 24, 1258291, 1, 1, 5, 11, 3, 9, 1, 15, 0xd},
> +	/* 324 */ {4, 1, 32, 1677722, 1, 1, 4, 9, 3, 8, 0, 15, 0x18},
> +	/* 432 */ {3, 1, 32, 1677722, 1, 1, 4, 9, 3, 8, 0, 15, 0x18}

We calculate all of prop_coef, int_coef, gain_ctl, targ_cnt,
dcoapovr_en_h, dco_amp, so no need to have fixed values for these. The
corresponding fields should be removed from bxt_clk_div and replaced
with local vars in bxt_ddi_pll_select.

>  };
>  
>  static bool
> @@ -1359,6 +1361,7 @@ bxt_ddi_pll_select(struct intel_crtc *intel_crtc,
>  {
>  	struct intel_shared_dpll *pll;
>  	struct bxt_clk_div clk_div = {0};
> +	int vco = 0;
>  
>  	if (intel_encoder->type == INTEL_OUTPUT_HDMI) {
>  		intel_clock_t best_clock;
> @@ -1382,11 +1385,7 @@ bxt_ddi_pll_select(struct intel_crtc *intel_crtc,
>  		clk_div.m2_frac = best_clock.m2 & ((1 << 22) - 1);
>  		clk_div.m2_frac_en = clk_div.m2_frac != 0;
>  
> -		/* FIXME: set coef, gain, targcnt based on freq band */
> -		clk_div.prop_coef = 5;
> -		clk_div.int_coef = 11;
> -		clk_div.gain_ctl = 2;
> -		clk_div.targ_cnt = 9;
> +		vco = best_clock.vco;
>  		if (clock > 270000)
>  			clk_div.lanestagger = 0x18;
>  		else if (clock > 135000)
> @@ -1416,6 +1415,32 @@ bxt_ddi_pll_select(struct intel_crtc *intel_crtc,
>  			clk_div = bxt_dp_clk_val[0];
>  			DRM_ERROR("Unknown link rate\n");
>  		}
> +		vco = clock * 10 / 2 * clk_div.p1 * clk_div.p2;
> +	}
> +
> +	clk_div.dco_amp = 15;
> +	clk_div.dcoampovr_en_h = 0;
> +	if (vco >= 6200000 && vco <= 6480000) {
> +		clk_div.prop_coef = 4;
> +		clk_div.int_coef = 9;
> +		clk_div.gain_ctl = 3;
> +		clk_div.targ_cnt = 8;
> +	} else if ((vco > 5400000 && vco < 6200000) ||
> +			(vco >= 4800000 && vco < 5400000)) {
> +		clk_div.prop_coef = 5;
> +		clk_div.int_coef = 11;
> +		clk_div.gain_ctl = 3;
> +		clk_div.targ_cnt = 9;
> +		if (vco >= 4800000 && vco < 5400000)
> +			clk_div.dcoampovr_en_h = 1;
> +	} else if (vco == 5400000) {
> +		clk_div.prop_coef = 3;
> +		clk_div.int_coef = 8;
> +		clk_div.gain_ctl = 1;
> +		clk_div.targ_cnt = 9;
> +	} else {
> +		DRM_ERROR("Invalid VCO\n");
> +		return false;
>  	}
>  
>  	crtc_state->dpll_hw_state.ebb0 =
> @@ -1435,6 +1460,11 @@ bxt_ddi_pll_select(struct intel_crtc *intel_crtc,
>  
>  	crtc_state->dpll_hw_state.pll8 = clk_div.targ_cnt;
>  
> +	if (clk_div.dcoampovr_en_h)
> +		crtc_state->dpll_hw_state.pll10 = PORT_PLL_DCO_AMP_OVR_EN_H;
> +
> +	crtc_state->dpll_hw_state.pll10 |= PORT_PLL_DCO_AMP(clk_div.dco_amp);
> +
>  	crtc_state->dpll_hw_state.pcsdw12 =
>  		LANESTAGGER_STRAP_OVRD | clk_div.lanestagger;
>  
> @@ -2366,10 +2396,16 @@ static void bxt_ddi_pll_enable(struct drm_i915_private *dev_priv,
>  	temp |= pll->config.hw_state.pll8;
>  	I915_WRITE(BXT_PORT_PLL(port, 8), temp);
>  
> -	/*
> -	 * FIXME: program PORT_PLL_9/i_lockthresh according to the latest
> -	 * specification update.
> -	 */
> +	temp = I915_READ(BXT_PORT_PLL(port, 9));
> +	temp &= ~PORT_PLL_LOCK_THRESHOLD_MASK;
> +	temp |= (5 << 1);
> +	I915_WRITE(BXT_PORT_PLL(port, 9), temp);
> +
> +	temp = I915_READ(BXT_PORT_PLL(port, 10));
> +	temp &= ~PORT_PLL_DCO_AMP_OVR_EN_H;
> +	temp &= ~PORT_PLL_DCO_AMP_MASK;
> +	temp |= pll->config.hw_state.pll10;
> +	I915_WRITE(BXT_PORT_PLL(port, 10), temp);
>  
>  	/* Recalibrate with new settings */
>  	temp = I915_READ(BXT_PORT_PLL_EBB_4(port));
> @@ -2433,6 +2469,7 @@ static bool bxt_ddi_pll_get_hw_state(struct drm_i915_private *dev_priv,
>  	hw_state->pll3 = I915_READ(BXT_PORT_PLL(port, 3));
>  	hw_state->pll6 = I915_READ(BXT_PORT_PLL(port, 6));
>  	hw_state->pll8 = I915_READ(BXT_PORT_PLL(port, 8));
> +	hw_state->pll10 = I915_READ(BXT_PORT_PLL(port, 10));
>  	/*
>  	 * While we write to the group register to program all lanes at once we
>  	 * can read only lane registers. We configure all lanes the same way, so


_______________________________________________
Intel-gfx mailing list
Intel-gfx@xxxxxxxxxxxxxxxxxxxxx
http://lists.freedesktop.org/mailman/listinfo/intel-gfx





[Index of Archives]     [Linux USB Devel]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]
  Powered by Linux