On Thursday 30 April 2015 01:23 AM, Ville Syrjälä wrote:
On Wed, Apr 29, 2015 at 06:31:56PM +0300, Ville Syrjälä wrote:
On Wed, Apr 29, 2015 at 08:23:21AM +0530, deepak.s@xxxxxxxxxxxxxxx wrote:
From: Deepak S <deepak.s@xxxxxxxxxxxxxxx>
After feedback from the hardware team, now we set the GPU min/idel freq to RPe.
Punit is expecting us to operate GPU between Rpe & Rp0. If we drop the
frequency to RPn, punit is failing to change the input voltage to
minimum :(
So far I can't reproduce this problem on my BSW. In fact what I see
that the voltage at RPn is lower than the voltage at RPe, even while
we're in rc6.
without forcewake:
RPn -> 0x66
RPe -> 0x67
RP0 -> 0x69
with forcewake:
RPn -> 0x66
RPe -> 0x76
RP0 -> 0x9d
Also asking Punit to change the frequency after the GPU has gone to
rc6 does absolutely nothing (remind anyone of VLV?). I think I need to
retest my VLV C0 to see if my earlier observations there were accurate.
The shared Vnn rail does make it harder to observe this stuff on
VLV though.
I went back to my VLVs (had a B3 and C0 actually). And I'm seeing the
exact same behaviour on both, ie. requesting a new frequency from Punit
does nothing when the GPU is in rc6, and if I let it enter rc6 with a
high frequency Vnn also remains high. Previously I had thought that C0
fixed this, but now it definitely shows the same problem here. I must
have had some accidental forcewake somewhere when I originally tested
it,
So based on that, your other patch to remove the stepping check from
vlv_set_rps_idle() is in fact correct.
The question remains however what should we do with CHV. According to my
testing to get the minimum voltage we should keep RPn around, and we
should also do the vlv_set_rps_idle() workaround on CHV.
Oh and I also observed something else on VLV. Normally when entering rc6
the GPLL ref clock gets trunk gated at CCK (by Punit I assume). However
when using the vlv_gfx_clock_force() that doesn't happen. So I'm not
entirely sure the GPLL gets turned off properly in that case. Maybe we
should just use forcewake instead? Oh and BTW, CHV doesn't do the trunk
gating in either case. I'm not sure where to check if the GPLL is
actually running or not.
Hi Ville,
Thanks Ville for verifying on VLV and CHV. Its interesting to see when Idle,
Voltage not dropping to Vnn on CHV :( This was supposed to be fixed
in BSW/CHV :(. As you suggested it would be better to extend the VLV WA to
CHV also to make sure we drop the voltage when idle.
Below is the sequence I think we should follow (based on your comments).
1. forcewake power wells
2. do gfx force clock on
3. request freq to punit
4. release gfx force clock on
5. release forcewake of power wells.
Please share your thoughts?
Thanks
Deepak
So based on my tests this patch feels a bit wrong.
Since Punit validates the rps range [RPe, RP0]. This patch
removes unused cherryview_rps_min_freq function.
v2: Change commit message
v3: set min_freq before idle_freq (chris)
v4: Squash 'Remove unused rps min function' patch
Signed-off-by: Deepak S <deepak.s@xxxxxxxxxxxxxxx>
Acked-by: Chris Wilson <chris@xxxxxxxxxxxxxxxxxx>
---
drivers/gpu/drm/i915/intel_pm.c | 21 ++-------------------
1 file changed, 2 insertions(+), 19 deletions(-)
diff --git a/drivers/gpu/drm/i915/intel_pm.c b/drivers/gpu/drm/i915/intel_pm.c
index a7516ed..78c89ff 100644
--- a/drivers/gpu/drm/i915/intel_pm.c
+++ b/drivers/gpu/drm/i915/intel_pm.c
@@ -4715,24 +4715,6 @@ static int cherryview_rps_guar_freq(struct drm_i915_private *dev_priv)
return rp1;
}
-static int cherryview_rps_min_freq(struct drm_i915_private *dev_priv)
-{
- struct drm_device *dev = dev_priv->dev;
- u32 val, rpn;
-
- if (dev->pdev->revision >= 0x20) {
- val = vlv_punit_read(dev_priv, FB_GFX_FMIN_AT_VMIN_FUSE);
- rpn = ((val >> FB_GFX_FMIN_AT_VMIN_FUSE_SHIFT) &
- FB_GFX_FREQ_FUSE_MASK);
- } else { /* For pre-production hardware */
- val = vlv_punit_read(dev_priv, PUNIT_GPU_STATUS_REG);
- rpn = ((val >> PUNIT_GPU_STATIS_GFX_MIN_FREQ_SHIFT) &
- PUNIT_GPU_STATUS_GFX_MIN_FREQ_MASK);
- }
-
- return rpn;
-}
-
static int valleyview_rps_guar_freq(struct drm_i915_private *dev_priv)
{
u32 val, rp1;
@@ -4984,7 +4966,8 @@ static void cherryview_init_gt_powersave(struct drm_device *dev)
intel_gpu_freq(dev_priv, dev_priv->rps.rp1_freq),
dev_priv->rps.rp1_freq);
- dev_priv->rps.min_freq = cherryview_rps_min_freq(dev_priv);
+ /* PUnit validated range is only [RPe, RP0] */
+ dev_priv->rps.min_freq = dev_priv->rps.efficient_freq;
DRM_DEBUG_DRIVER("min GPU freq: %d MHz (%u)\n",
intel_gpu_freq(dev_priv, dev_priv->rps.min_freq),
dev_priv->rps.min_freq);
--
1.9.1
--
Ville Syrjälä
Intel OTC
_______________________________________________
Intel-gfx mailing list
Intel-gfx@xxxxxxxxxxxxxxxxxxxxx
http://lists.freedesktop.org/mailman/listinfo/intel-gfx
_______________________________________________
Intel-gfx mailing list
Intel-gfx@xxxxxxxxxxxxxxxxxxxxx
http://lists.freedesktop.org/mailman/listinfo/intel-gfx
