On Sat, Sep 20, 2014 at 02:47:05AM +0800, Jike Song wrote:
> From: Yu Zhang <yu.c.zhang@xxxxxxxxx>
>
> Display switch logic is added to notify the vgt mediator that
> current vgpu have a valid surface to show. It does so by writing
> the display_ready field in PV INFO page, and then will be handled
> in vgt mediator. This is useful to avoid trickiness when the VM's
> framebuffer is being accessed in the middle of VM modesetting,
> e.g. compositing the framebuffer in the host side
>
> Signed-off-by: Yu Zhang <yu.c.zhang@xxxxxxxxx>
> Signed-off-by: Jike Song <jike.song@xxxxxxxxx>
> Signed-off-by: Zhiyuan Lv <zhiyuan.lv@xxxxxxxxx>
> ---
> drivers/gpu/drm/i915/i915_dma.c | 8 ++++++++
> drivers/gpu/drm/i915/i915_reg.h | 7 +++++++
> drivers/gpu/drm/i915/intel_display.c | 10 ++++++++++
> 3 files changed, 25 insertions(+)
>
> diff --git a/drivers/gpu/drm/i915/i915_dma.c b/drivers/gpu/drm/i915/i915_dma.c
> index bb4ad52..d9462e1 100644
> --- a/drivers/gpu/drm/i915/i915_dma.c
> +++ b/drivers/gpu/drm/i915/i915_dma.c
> @@ -1790,6 +1790,14 @@ int i915_driver_load(struct drm_device *dev, unsigned long flags)
> } else {
> /* Start out suspended in ums mode. */
> dev_priv->ums.mm_suspended = 1;
> + if (intel_vgpu_active(dev)) {
> + /*
> + * Notify a valid surface after modesetting,
> + * when running inside a VM.
> + */
> + I915_WRITE(vgt_info_off(display_ready),
> + VGT_DRV_DISPLAY_READY);
That's interesting. As i915.ko is definitely not ready at this point.
> + }
> }
>
> i915_setup_sysfs(dev);
> diff --git a/drivers/gpu/drm/i915/i915_reg.h b/drivers/gpu/drm/i915/i915_reg.h
> index a70f12e..38d606c 100644
> --- a/drivers/gpu/drm/i915/i915_reg.h
> +++ b/drivers/gpu/drm/i915/i915_reg.h
> @@ -6673,5 +6673,12 @@ enum punit_power_well {
> #define vgt_info_off(x) \
> (VGT_PVINFO_PAGE + (long)&((struct vgt_if *) NULL)->x)
>
> +/*
> + * The information set by the guest gfx driver, through the display_ready field
> + */
> +enum vgt_display_status {
> + VGT_DRV_DISPLAY_NOT_READY = 0,
> + VGT_DRV_DISPLAY_READY, /* ready for display switch */
> +};
>
> #endif /* _I915_REG_H_ */
> diff --git a/drivers/gpu/drm/i915/intel_display.c b/drivers/gpu/drm/i915/intel_display.c
> index b78f00a..3af9259 100644
> --- a/drivers/gpu/drm/i915/intel_display.c
> +++ b/drivers/gpu/drm/i915/intel_display.c
> @@ -11642,6 +11642,16 @@ static int intel_crtc_set_config(struct drm_mode_set *set)
> intel_modeset_check_state(set->crtc->dev);
> }
>
> + if (intel_vgpu_active(dev)) {
> + /*
> + * Notify a valid surface after modesetting,
> + * when running inside a VM.
> + */
> + struct drm_i915_private *dev_priv = dev->dev_private;
> +
> + I915_WRITE(vgt_info_off(display_ready), VGT_DRV_DISPLAY_READY);
Should there not be some coordination before we start the modeset?
-Chris
--
Chris Wilson, Intel Open Source Technology Centre
_______________________________________________
Intel-gfx mailing list
Intel-gfx@xxxxxxxxxxxxxxxxxxxxx
http://lists.freedesktop.org/mailman/listinfo/intel-gfx
