[PATCH 06/17] drm/i915: move intel_update_lvds to intel_lvds->pre_pll_enable

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



A few things needed to change:
- HAS_PCH_SPLIT since ilk+ is not yet converted to this.
- s/LVDS/intel_lvds->reg/ to prep for ilk conversion
- replace the clock.p2 == 7 check with a is_dual_link check
- s/adjusted_mode/intel_lvds->fixed_mode

v2: Rebase on top of Jani Nikula's panel rework. I'm wondering whether
we shouldn't add an attached_panel pointer to intel_encoder, to
replace the encoder private ->attached_connector pointers, since
that's essentially what we need.

Reviewed-by: Paulo Zanoni <paulo.r.zanoni at intel.com>
Signed-off-by: Daniel Vetter <daniel.vetter at ffwll.ch>
---
 drivers/gpu/drm/i915/intel_display.c | 59 ------------------------------------
 drivers/gpu/drm/i915/intel_lvds.c    | 57 ++++++++++++++++++++++++++++++++++
 2 files changed, 57 insertions(+), 59 deletions(-)

diff --git a/drivers/gpu/drm/i915/intel_display.c b/drivers/gpu/drm/i915/intel_display.c
index 1048595..1e88364 100644
--- a/drivers/gpu/drm/i915/intel_display.c
+++ b/drivers/gpu/drm/i915/intel_display.c
@@ -4255,51 +4255,6 @@ static void i9xx_update_pll_dividers(struct drm_crtc *crtc,
 	}
 }
 
-static void intel_update_lvds(struct drm_crtc *crtc, intel_clock_t *clock,
-			      struct drm_display_mode *adjusted_mode)
-{
-	struct drm_device *dev = crtc->dev;
-	struct drm_i915_private *dev_priv = dev->dev_private;
-	struct intel_crtc *intel_crtc = to_intel_crtc(crtc);
-	int pipe = intel_crtc->pipe;
-	u32 temp;
-
-	temp = I915_READ(LVDS);
-	temp |= LVDS_PORT_EN | LVDS_A0A2_CLKA_POWER_UP;
-	if (pipe == 1) {
-		temp |= LVDS_PIPEB_SELECT;
-	} else {
-		temp &= ~LVDS_PIPEB_SELECT;
-	}
-	/* set the corresponsding LVDS_BORDER bit */
-	temp |= dev_priv->lvds_border_bits;
-	/* Set the B0-B3 data pairs corresponding to whether we're going to
-	 * set the DPLLs for dual-channel mode or not.
-	 */
-	if (clock->p2 == 7)
-		temp |= LVDS_B0B3_POWER_UP | LVDS_CLKB_POWER_UP;
-	else
-		temp &= ~(LVDS_B0B3_POWER_UP | LVDS_CLKB_POWER_UP);
-
-	/* It would be nice to set 24 vs 18-bit mode (LVDS_A3_POWER_UP)
-	 * appropriately here, but we need to look more thoroughly into how
-	 * panels behave in the two modes.
-	 */
-	/* set the dithering flag on LVDS as needed */
-	if (INTEL_INFO(dev)->gen >= 4) {
-		if (dev_priv->lvds_dither)
-			temp |= LVDS_ENABLE_DITHER;
-		else
-			temp &= ~LVDS_ENABLE_DITHER;
-	}
-	temp &= ~(LVDS_HSYNC_POLARITY | LVDS_VSYNC_POLARITY);
-	if (adjusted_mode->flags & DRM_MODE_FLAG_NHSYNC)
-		temp |= LVDS_HSYNC_POLARITY;
-	if (adjusted_mode->flags & DRM_MODE_FLAG_NVSYNC)
-		temp |= LVDS_VSYNC_POLARITY;
-	I915_WRITE(LVDS, temp);
-}
-
 static void vlv_update_pll(struct drm_crtc *crtc,
 			   struct drm_display_mode *mode,
 			   struct drm_display_mode *adjusted_mode,
@@ -4482,13 +4437,6 @@ static void i9xx_update_pll(struct drm_crtc *crtc,
 		if (encoder->pre_pll_enable)
 			encoder->pre_pll_enable(encoder);
 
-	/* The LVDS pin pair needs to be on before the DPLLs are enabled.
-	 * This is an exception to the general rule that mode_set doesn't turn
-	 * things on.
-	 */
-	if (intel_pipe_has_type(crtc, INTEL_OUTPUT_LVDS))
-		intel_update_lvds(crtc, clock, adjusted_mode);
-
 	if (intel_pipe_has_type(crtc, INTEL_OUTPUT_DISPLAYPORT))
 		intel_dp_set_m_n(crtc, mode, adjusted_mode);
 
@@ -4564,13 +4512,6 @@ static void i8xx_update_pll(struct drm_crtc *crtc,
 		if (encoder->pre_pll_enable)
 			encoder->pre_pll_enable(encoder);
 
-	/* The LVDS pin pair needs to be on before the DPLLs are enabled.
-	 * This is an exception to the general rule that mode_set doesn't turn
-	 * things on.
-	 */
-	if (intel_pipe_has_type(crtc, INTEL_OUTPUT_LVDS))
-		intel_update_lvds(crtc, clock, adjusted_mode);
-
 	I915_WRITE(DPLL(pipe), dpll);
 
 	/* Wait for the clocks to stabilize. */
diff --git a/drivers/gpu/drm/i915/intel_lvds.c b/drivers/gpu/drm/i915/intel_lvds.c
index a6aec59..e3a68a1 100644
--- a/drivers/gpu/drm/i915/intel_lvds.c
+++ b/drivers/gpu/drm/i915/intel_lvds.c
@@ -89,6 +89,62 @@ static bool intel_lvds_get_hw_state(struct intel_encoder *encoder,
 	return true;
 }
 
+/* The LVDS pin pair needs to be on before the DPLLs are enabled.
+ * This is an exception to the general rule that mode_set doesn't turn
+ * things on.
+ */
+static void intel_pre_pll_enable_lvds(struct intel_encoder *encoder)
+{
+	struct intel_lvds_encoder *lvds_encoder = to_lvds_encoder(&encoder->base);
+	struct drm_device *dev = encoder->base.dev;
+	struct drm_i915_private *dev_priv = dev->dev_private;
+	struct intel_crtc *intel_crtc = to_intel_crtc(encoder->base.crtc);
+	struct drm_display_mode *fixed_mode =
+		lvds_encoder->attached_connector->base.panel.fixed_mode;
+	int pipe = intel_crtc->pipe;
+	u32 temp;
+
+	/* pch split platforms are not yet converted. */
+	if (HAS_PCH_SPLIT(dev))
+		return;
+
+	temp = I915_READ(lvds_encoder->reg);
+	temp |= LVDS_PORT_EN | LVDS_A0A2_CLKA_POWER_UP;
+	if (pipe == 1) {
+		temp |= LVDS_PIPEB_SELECT;
+	} else {
+		temp &= ~LVDS_PIPEB_SELECT;
+	}
+	/* set the corresponsding LVDS_BORDER bit */
+	temp |= dev_priv->lvds_border_bits;
+	/* Set the B0-B3 data pairs corresponding to whether we're going to
+	 * set the DPLLs for dual-channel mode or not.
+	 */
+	if (lvds_encoder->is_dual_link)
+		temp |= LVDS_B0B3_POWER_UP | LVDS_CLKB_POWER_UP;
+	else
+		temp &= ~(LVDS_B0B3_POWER_UP | LVDS_CLKB_POWER_UP);
+
+	/* It would be nice to set 24 vs 18-bit mode (LVDS_A3_POWER_UP)
+	 * appropriately here, but we need to look more thoroughly into how
+	 * panels behave in the two modes.
+	 */
+	/* set the dithering flag on LVDS as needed */
+	if (INTEL_INFO(dev)->gen >= 4) {
+		if (dev_priv->lvds_dither)
+			temp |= LVDS_ENABLE_DITHER;
+		else
+			temp &= ~LVDS_ENABLE_DITHER;
+	}
+	temp &= ~(LVDS_HSYNC_POLARITY | LVDS_VSYNC_POLARITY);
+	if (fixed_mode->flags & DRM_MODE_FLAG_NHSYNC)
+		temp |= LVDS_HSYNC_POLARITY;
+	if (fixed_mode->flags & DRM_MODE_FLAG_NVSYNC)
+		temp |= LVDS_VSYNC_POLARITY;
+
+	I915_WRITE(lvds_encoder->reg, temp);
+}
+
 /**
  * Sets the power state for the panel.
  */
@@ -1038,6 +1094,7 @@ bool intel_lvds_init(struct drm_device *dev)
 			 DRM_MODE_ENCODER_LVDS);
 
 	intel_encoder->enable = intel_enable_lvds;
+	intel_encoder->pre_pll_enable = intel_pre_pll_enable_lvds;
 	intel_encoder->disable = intel_disable_lvds;
 	intel_encoder->get_hw_state = intel_lvds_get_hw_state;
 	intel_connector->get_hw_state = intel_connector_get_hw_state;
-- 
1.7.11.7



[Index of Archives]     [Linux USB Devel]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]
  Powered by Linux