On 15/07/16 15:42, Goel, Akash wrote:
On 7/15/2016 5:27 PM, Tvrtko Ursulin wrote:
On 10/07/16 14:41, akash.goel@xxxxxxxxx wrote:
From: Akash Goel <akash.goel@xxxxxxxxx>
In cases where GuC generate logs at a very high rate, correspondingly
the rate of flush interrupts is also very high.
So far total 8 pages were allocated for storing both ISR & DPC logs.
As per the half-full draining protocol followed by GuC, by doubling
the number of pages, the frequency of flush interrupts can be cut down
to almost half, which then helps in reducing the logging overhead.
So now allocating 8 pages apiece for ISR & DPC logs.
Suggested-by: Tvrtko Ursulin <tvrtko.ursulin@xxxxxxxxx>
Signed-off-by: Akash Goel <akash.goel@xxxxxxxxx>
---
drivers/gpu/drm/i915/intel_guc_fwif.h | 8 ++++----
1 file changed, 4 insertions(+), 4 deletions(-)
diff --git a/drivers/gpu/drm/i915/intel_guc_fwif.h
b/drivers/gpu/drm/i915/intel_guc_fwif.h
index 1de6928..7521ed5 100644
--- a/drivers/gpu/drm/i915/intel_guc_fwif.h
+++ b/drivers/gpu/drm/i915/intel_guc_fwif.h
@@ -104,9 +104,9 @@
#define GUC_LOG_ALLOC_IN_MEGABYTE (1 << 3)
#define GUC_LOG_CRASH_PAGES 1
#define GUC_LOG_CRASH_SHIFT 4
-#define GUC_LOG_DPC_PAGES 3
+#define GUC_LOG_DPC_PAGES 7
#define GUC_LOG_DPC_SHIFT 6
-#define GUC_LOG_ISR_PAGES 3
+#define GUC_LOG_ISR_PAGES 7
#define GUC_LOG_ISR_SHIFT 9
#define GUC_LOG_BUF_ADDR_SHIFT 12
@@ -436,9 +436,9 @@ enum guc_log_buffer_type {
* | Crash dump state header |
* Page1 +-------------------------------+
* | ISR logs |
- * Page5 +-------------------------------+
- * | DPC logs |
* Page9 +-------------------------------+
+ * | DPC logs |
+ * Page17 +-------------------------------+
* | Crash Dump logs |
* +-------------------------------+
*
I don't mind - but does it help? And how much and for what? Haven't you
later found that the uncached reads were the main issue?
This change along with kthread patch, helped reduce the overflow counts
and even eliminate them for some benchmarks.
Though with the impending optimization for Uncached reads there should
be further improvements but in my view, notwithstanding the improvement
w.r.t overflow count, its still a better configuration to work with as
flush interrupt frequency is cut down to half and not able to see any
apparent downsides to it.
I was primarily thinking to go with a minimal and simplest set of
patches to implement the feature.
Logic was that apparently none of the smart and complex optimisations
managed to solve the dropped interrupt issue, until the slowness of the
uncached read was discovered to be the real/main issue.
So it seems that is something that definitely needs to be implemented.
(Whether or not it will be possible to use SSE instructions to do the
read I don't know.)
Assuming it is possible, then the question is whether there is need for
all the other optimisations. Ie. do we need the kthread with rtprio or
would a simple worker be enough? Do we need the new i915 param for
tweaking the relay sub-buffers? Do we need the increase of the log
buffer size? The extra patch to do smarter reads?
If we do not have the issue of the dropped interrupts with none of these
extra patches applied, then we could afford to not bother with them now.
Would make the series shorter and review easier and the feature in quicker.
Or maybe we do need all the advanced stuff, I don't know, I am just
asking the question and would like to see some data.
Regards,
Tvrtko
_______________________________________________
Intel-gfx mailing list
Intel-gfx@xxxxxxxxxxxxxxxxxxxxx
https://lists.freedesktop.org/mailman/listinfo/intel-gfx
