[PATCH 3/4] nl80211: fix simultaneous scanning failure in case of MLO

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Currently only 1 scan can be performed on per phy level at a time in
driver. Due to this, if via other underlying phy, a scan request is sent,
kernel returns -EBUSY. And then hostapd would try to set the interface in
station mode if it was originally in AP mode and retry sending a scan
request. However, this behaviour is expected in case of multi link
operation and hence there is no need to switch the mode as such.

Hence, add logic to not change the NL mode if kernel returns -EBUSY during
multi link AP operation. The caller can accordingly decide and if needed,
it can re-schedule a scan request after some time.

Signed-off-by: Aditya Kumar Singh <quic_adisi@xxxxxxxxxxx>
---
 src/drivers/driver_nl80211_scan.c | 34 +++++++++++++++++++++++++++++++
 1 file changed, 34 insertions(+)

diff --git a/src/drivers/driver_nl80211_scan.c b/src/drivers/driver_nl80211_scan.c
index 68deb2d9e296..95c7ba80e81a 100644
--- a/src/drivers/driver_nl80211_scan.c
+++ b/src/drivers/driver_nl80211_scan.c
@@ -413,6 +413,40 @@ int wpa_driver_nl80211_scan(struct i802_bss *bss,
 		if (drv->hostapd && is_ap_interface(drv->nlmode)) {
 			enum nl80211_iftype old_mode = drv->nlmode;
 
+#ifdef CONFIG_IEEE80211BE
+			/* For Multi Link BSS, retry scan if any other links
+			 * are busy scanning
+			 */
+			if (ret == -EBUSY &&
+			    nl80211_link_valid(bss->valid_links, params->mlo_link_id)) {
+				struct i802_bss *link_bss;
+				u8 link_id;
+
+				wpa_printf(MSG_DEBUG,
+					   "nl80211: Scan trigger on Multi Link BSS failed (requested link=%d on interface %s)",
+					   params->mlo_link_id, bss->ifname);
+
+				for (link_bss = drv->first_bss; link_bss;
+				     link_bss = link_bss->next)
+					if (link_bss->scan_link)
+						break;
+
+				if (!link_bss) {
+					wpa_printf(MSG_DEBUG,
+						   "nl80211: Interface information already running scan not available");
+					goto fail;
+				}
+
+				link_id =
+				       nl80211_get_link_id_from_link(link_bss,
+								     link_bss->scan_link);
+				wpa_printf(MSG_DEBUG,
+					   "nl80211: Scan already running on interface %s link %d",
+					   link_bss->ifname, link_id);
+				goto fail;
+			}
+#endif /* CONFIG_IEEE80211BE */
+
 			/*
 			 * mac80211 does not allow scan requests in AP mode, so
 			 * try to do this in station mode.
-- 
2.34.1


_______________________________________________
Hostap mailing list
Hostap@xxxxxxxxxxxxxxxxxxx
http://lists.infradead.org/mailman/listinfo/hostap



[Index of Archives]     [Linux Wireless]     [Linux Kernel]     [ATH6KL]     [Linux Bluetooth]     [Linux Netdev]     [Kernel Newbies]     [IDE]     [Security]     [Git]     [Netfilter]     [Bugtraq]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Linux ATA RAID]     [Samba]     [Device Mapper]

  Powered by Linux