My home wireless router is a Proxmox VE server, that manage some VMs bus also my wireless; practically speking is a debian buster (so hostapd version 2:2.7+git20190128+0c1e29f-6+deb10u2, with a slightly newer kernel, 5.4.78-2-pve). To improve my wireless experience i've bought a newer PCI-E wireless card, based on 'Wifi6' Intel AX200 chipset. Board seems correctly identified by kernel: Jan 23 18:40:00 ino kernel: [ 8.398005] iwlwifi 0000:10:00.0: TLV_FW_FSEQ_VERSION: FSEQ Version: 58.3.35.22 Jan 23 18:40:00 ino kernel: [ 8.398010] iwlwifi 0000:10:00.0: Found debug destination: EXTERNAL_DRAM Jan 23 18:40:00 ino kernel: [ 8.398011] iwlwifi 0000:10:00.0: Found debug configuration: 0 Jan 23 18:40:00 ino kernel: [ 8.398350] iwlwifi 0000:10:00.0: loaded firmware version 50.3e391d3e.0 op_mode iwlmvm Jan 23 18:40:00 ino kernel: [ 8.431011] iwlwifi 0000:10:00.0: Detected Intel(R) Wi-Fi 6 AX200 160MHz, REV=0x340 Jan 23 18:40:00 ino kernel: [ 8.443718] iwlwifi 0000:10:00.0: Applying debug destination EXTERNAL_DRAM Jan 23 18:40:00 ino kernel: [ 8.444616] iwlwifi 0000:10:00.0: Allocated 0x00400000 bytes for firmware monitor. Jan 23 18:40:00 ino kernel: [ 8.603713] iwlwifi 0000:10:00.0: base HW address: 78:2b:46:2e:4a:87 Jan 23 18:40:00 ino kernel: [ 8.701453] iwlwifi 0000:10:00.0 wls1: renamed from wlan0 but when i run 'hostapd' with a rather standard config file (that work with current board), hostapd exit silently: [...] CS: Automatic channel selection started, this may take a bit ACS: Scanning 1 / 5 wls1: nl80211: scan request nl80211: Passive scan requested nl80211: Scan frequency 2412 MHz nl80211: Scan frequency 2417 MHz nl80211: Scan frequency 2422 MHz nl80211: Scan frequency 2427 MHz nl80211: Scan frequency 2432 MHz nl80211: Scan frequency 2437 MHz nl80211: Scan frequency 2442 MHz nl80211: Scan frequency 2447 MHz nl80211: Scan frequency 2452 MHz nl80211: Scan frequency 2457 MHz nl80211: Scan frequency 2462 MHz nl80211: Scan frequency 2467 MHz nl80211: Scan frequency 2472 MHz Scan requested (ret=0) - scan timeout 10 seconds wls1: interface state COUNTRY_UPDATE->ACS wls1: ACS-STARTED Interface initialization will be completed in a callback (ACS) ctrl_iface not configured! on kernel i saw: Jan 23 18:40:00 ino kernel: [ 12.590677] iwlwifi 0000:10:00.0: Applying debug destination EXTERNAL_DRAM Jan 23 18:40:01 ino kernel: [ 12.744547] iwlwifi 0000:10:00.0: FW already configured (0) - re-configuring What i'm missing? Thanks. -- Marco ``Gaio'' Gaiarin | Pordenone Linux User Group (https://www.pnlug.it/) P.zza S. Tommaso, 20 | Lilliput BBS (http://bbs.lilliput.linux.it) Cimpello di Fiume Veneto | Azione Cattolica - Concordia-Pordenone 33080 Pordenone (Italia) | (https://www.acconcordiapn.it/) Tel. +39-0434-56-1305 | Mastodon:@marcogaio@sociale.network gaio@xxxxxxxx _______________________________________________ Hostap mailing list Hostap@xxxxxxxxxxxxxxxxxxx http://lists.infradead.org/mailman/listinfo/hostap
