Re: immediate disassociated with hostapd 2.9. 2.5 work fine

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



did some more searching and found i need to specify the bridge in my config so i added:

bridge=br0

but it doesn't help.. running hostapd with -dd shows (see below)
(I've marked in the below log where it says 'authenticated->disassociated )

any ideas where i could look further ?

thanks,
tom


# ./hostapd -dd -e /root/entropy  /etc/hostapd-psk-emmy.conf
random: Added entropy from /root/entropy (own_pool_ready=2)
random: Trying to read entropy from /dev/random
Get randomness: len=20 entropy=1
random: Updated entropy file /root/entropy (own_pool_ready=2)
Configuration file: /etc/hostapd-psk-emmy.conf
ctrl_interface_group=0
nl80211: TDLS supported
nl80211: TDLS external setup
nl80211: Supported cipher 00-0f-ac:1
nl80211: Supported cipher 00-0f-ac:5
nl80211: Supported cipher 00-0f-ac:2
nl80211: Supported cipher 00-0f-ac:4
nl80211: Supported cipher 00-14-72:1
nl80211: Supported cipher 00-0f-ac:6
nl80211: Supports Probe Response offload in AP mode
nl80211: Using driver-based off-channel TX
nl80211: TDLS channel switch
nl80211: Driver-advertised extended capabilities (default) - hexdump(len=10): 00 00 00 00 00 00 00 00 00 00 nl80211: Driver-advertised extended capabilities mask (default) - hexdump(len=10): 00 00 00 00 00 00 00 00 00 00
nl80211: Supported vendor command: vendor_id=0x5043 subcmd=0
nl80211: Supported vendor command: vendor_id=0x5043 subcmd=4105
nl80211: Supported vendor command: vendor_id=0x5043 subcmd=5376
nl80211: Supported vendor command: vendor_id=0x5043 subcmd=5
nl80211: Supported vendor command: vendor_id=0x5043 subcmd=256
nl80211: Supported vendor command: vendor_id=0x5043 subcmd=5126
nl80211: Supported vendor command: vendor_id=0x5043 subcmd=5124
nl80211: Supported vendor command: vendor_id=0x5043 subcmd=4106
nl80211: Supported vendor command: vendor_id=0x5043 subcmd=4109
nl80211: Supported vendor event: vendor_id=0x5043 subcmd=0
nl80211: Supported vendor event: vendor_id=0x5043 subcmd=5377
nl80211: Supported vendor event: vendor_id=0x5043 subcmd=65540
nl80211: Supported vendor event: vendor_id=0x5043 subcmd=65541
nl80211: Supported vendor event: vendor_id=0x5043 subcmd=65542
nl80211: Supported vendor event: vendor_id=0x5043 subcmd=65543
nl80211: Supported vendor event: vendor_id=0x5043 subcmd=65544
nl80211: Use separate P2P group interface (driver advertised support)
nl80211: Enable multi-channel concurrent (driver advertised support)
nl80211: interface uap0 in phy mwiphy0
nl80211: Set mode ifindex 4 iftype 3 (AP)
nl80211: Setup AP(uap0) - device_ap_sme=1 use_monitor=0
nl80211: Subscribe to mgmt frames with AP handle 0x198f978 (device SME)
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x198f978 match=04 nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x198f978 match=0501 nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x198f978 match=0503 nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x198f978 match=0504 nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x198f978 match=06 nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x198f978 match=09 nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x198f978 match=0a nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x198f978 match=11 nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x198f978 match=7f nl80211: Register frame type=0xb0 (WLAN_FC_STYPE_AUTH) nl_handle=0x198f978 match=
nl80211: Enable Probe Request reporting nl_preq=0x198f838
nl80211: Register frame type=0x40 (WLAN_FC_STYPE_PROBE_REQ) nl_handle=0x198f838 match=
rfkill: Cannot open RFKILL control device
nl80211: RFKILL status not available
nl80211: Add own interface ifindex 6 (ifidx_reason 4)
nl80211: if_indices[16]: 6(4)
nl80211: Add own interface ifindex 4 (ifidx_reason -1)
nl80211: if_indices[16]: 6(4) 4(-1)
nl80211: Adding interface uap0 into bridge br0
phy: mwiphy0
BSS count 1, BSSID mask 00:00:00:00:00:00 (0 bits)
nl80211: Regulatory information - country=00
nl80211: 2402-2472 @ 40 MHz 20 mBm
nl80211: 2457-2482 @ 40 MHz 20 mBm (no IR)
nl80211: 2474-2494 @ 20 MHz 20 mBm (no OFDM) (no IR)
nl80211: 5170-5250 @ 160 MHz 20 mBm (no IR)
nl80211: 5250-5330 @ 160 MHz 20 mBm (DFS) (no IR)
nl80211: 5490-5730 @ 160 MHz 20 mBm (DFS) (no IR)
nl80211: 5735-5835 @ 80 MHz 20 mBm (no IR)
nl80211: 57240-63720 @ 2160 MHz 0 mBm
nl80211: Added 802.11b mode based on 802.11g information
nl80211: Mode IEEE 802.11g: 2412 2417 2422 2427 2432 2437 2442 2447 2452 2457 2462 2467[NO_IR] 2472[NO_IR] 2484[NO_IR] nl80211: Mode IEEE 802.11a: 5180[NO_IR] 5200[NO_IR] 5220[NO_IR] 5240[NO_IR] 5260[NO_IR][RADAR] 5280[NO_IR][RADAR] 5300[NO_IR][RADAR] 5320[NO_IR][RADAR] 5500[NO_IR][RADAR] 5520[NO_IR][RADAR] 5540[NO_IR][RADAR] nl80211: Mode IEEE 802.11b: 2412 2417 2422 2427 2432 2437 2442 2447 2452 2457 2462 2467[NO_IR] 2472[NO_IR] 2484[NO_IR]
Allowed channel: mode=1 chan=1 freq=2412 MHz max_tx_power=20 dBm
Allowed channel: mode=1 chan=2 freq=2417 MHz max_tx_power=20 dBm
Allowed channel: mode=1 chan=3 freq=2422 MHz max_tx_power=20 dBm
Allowed channel: mode=1 chan=4 freq=2427 MHz max_tx_power=20 dBm
Allowed channel: mode=1 chan=5 freq=2432 MHz max_tx_power=20 dBm
Allowed channel: mode=1 chan=6 freq=2437 MHz max_tx_power=20 dBm
Allowed channel: mode=1 chan=7 freq=2442 MHz max_tx_power=20 dBm
Allowed channel: mode=1 chan=8 freq=2447 MHz max_tx_power=20 dBm
Allowed channel: mode=1 chan=9 freq=2452 MHz max_tx_power=20 dBm
Allowed channel: mode=1 chan=10 freq=2457 MHz max_tx_power=20 dBm
Allowed channel: mode=1 chan=11 freq=2462 MHz max_tx_power=20 dBm
Allowed channel: mode=0 chan=1 freq=2412 MHz max_tx_power=20 dBm
Allowed channel: mode=0 chan=2 freq=2417 MHz max_tx_power=20 dBm
Allowed channel: mode=0 chan=3 freq=2422 MHz max_tx_power=20 dBm
Allowed channel: mode=0 chan=4 freq=2427 MHz max_tx_power=20 dBm
Allowed channel: mode=0 chan=5 freq=2432 MHz max_tx_power=20 dBm
Allowed channel: mode=0 chan=6 freq=2437 MHz max_tx_power=20 dBm
Allowed channel: mode=0 chan=7 freq=2442 MHz max_tx_power=20 dBm
Allowed channel: mode=0 chan=8 freq=2447 MHz max_tx_power=20 dBm
Allowed channel: mode=0 chan=9 freq=2452 MHz max_tx_power=20 dBm
Allowed channel: mode=0 chan=10 freq=2457 MHz max_tx_power=20 dBm
Allowed channel: mode=0 chan=11 freq=2462 MHz max_tx_power=20 dBm
Completing interface initialization
Mode: IEEE 802.11g  Channel: 6  Frequency: 2437 MHz
DFS 0 channels required radar detection
nl80211: Set freq 2437 (ht_enabled=0, vht_enabled=0, he_enabled=0, bandwidth=20 MHz, cf1=2437 MHz, cf2=0 MHz)
  * freq=2437
  * he_enabled=0
  * vht_enabled=0
  * ht_enabled=0
  * channel_type=0
RATE[0] rate=10 flags=0x1
RATE[1] rate=20 flags=0x1
RATE[2] rate=55 flags=0x1
RATE[3] rate=110 flags=0x1
RATE[4] rate=60 flags=0x0
RATE[5] rate=90 flags=0x0
RATE[6] rate=120 flags=0x0
RATE[7] rate=180 flags=0x0
RATE[8] rate=240 flags=0x0
RATE[9] rate=360 flags=0x0
RATE[10] rate=480 flags=0x0
RATE[11] rate=540 flags=0x0
hostapd_setup_bss(hapd=0x198f178 (uap0), first=1)
uap0: Flushing old station entries
nl80211: flush -> DEL_STATION uap0 (all)
uap0: Deauthenticate all stations
nl80211: sta_remove -> DEL_STATION uap0 ff:ff:ff:ff:ff:ff --> 0 (Success)
wpa_driver_nl80211_set_key: ifindex=4 (uap0) alg=0 addr=(nil) key_idx=0 set_tx=0 seq_len=0 key_len=0 wpa_driver_nl80211_set_key: ifindex=4 (uap0) alg=0 addr=(nil) key_idx=1 set_tx=0 seq_len=0 key_len=0 wpa_driver_nl80211_set_key: ifindex=4 (uap0) alg=0 addr=(nil) key_idx=2 set_tx=0 seq_len=0 key_len=0 wpa_driver_nl80211_set_key: ifindex=4 (uap0) alg=0 addr=(nil) key_idx=3 set_tx=0 seq_len=0 key_len=0
Using interface uap0 with hwaddr d4:ca:6e:6a:6a:59 and ssid "myssid"
Deriving WPA PSK based on passphrase
SSID - hexdump_ascii(len=6):
     6d 79 73 73 69 64 myssid
PSK (ASCII passphrase) - hexdump_ascii(len=10): [REMOVED]
PSK (from passphrase) - hexdump(len=32): [REMOVED]
random: Got 20/20 random bytes
Get randomness: len=20 entropy=0
random: Updated entropy file /root/entropy (own_pool_ready=2)
Get randomness: len=32 entropy=0
GMK - hexdump(len=32): [REMOVED]
Get randomness: len=32 entropy=0
Key Counter - hexdump(len=32): [REMOVED]
WPA: Delay group state machine start until Beacon frames have been configured
nl80211: Set beacon (beacon_set=0)
nl80211: Beacon head - hexdump(len=57): 80 00 00 00 ff ff ff ff ff ff d4 ca 6e 6a 6a 59 d4 ca 6e 6a 6a 59 00 00 00 00 00 00 00 00 00 00 64 00 11 04 00 06 6d 79 73 73 69 64 01 08 82 84 8b 96 0c 12 18 24 03 01 06 nl80211: Beacon tail - hexdump(len=38): 2a 01 04 32 04 30 48 60 6c 30 14 01 00 00 0f ac 02 01 00 00 0f ac 02 01 00 00 0f ac 02 00 00 3b 02 51 00 7f 01 04
nl80211: ifindex=4
nl80211: beacon_int=100
nl80211: beacon_rate=0
nl80211: rate_type=0
nl80211: dtim_period=2
nl80211: ssid=myssid
  * beacon_int=100
  * dtim_period=2
nl80211: proberesp (offload) - hexdump(len=95): 50 00 00 00 00 00 00 00 00 00 d4 ca 6e 6a 6a 59 d4 ca 6e 6a 6a 59 00 00 00 00 00 00 00 00 00 00 64 00 11 04 00 06 6d 79 73 73 69 64 01 08 82 84 8b 96 0c 12 18 24 03 01 06 2a 01 04 32 04 30 48 60 6c 30 14 01 00 00 0f ac 02 01 00 00 0f ac 02 01 00 00 0f ac 02 00 00 3b 02 51 00 7f 01 04
nl80211: hidden SSID not in use
nl80211: privacy=1
nl80211: auth_algs=0x1
nl80211: wpa_version=0x2
nl80211: key_mgmt_suites=0x2
nl80211: pairwise_ciphers=0x8
nl80211: group_cipher=0x8
nl80211: beacon_ies - hexdump(len=3): 7f 01 04
nl80211: proberesp_ies - hexdump(len=3): 7f 01 04
nl80211: assocresp_ies - hexdump(len=3): 7f 01 04
nl80211: ap_max_inactivity=300
WPA: Start group state machine to set initial keys
WPA: group state machine entering state GTK_INIT (VLAN-ID 0)
Get randomness: len=32 entropy=0
GTK - hexdump(len=32): [REMOVED]
WPA: group state machine entering state SETKEYSDONE (VLAN-ID 0)
wpa_driver_nl80211_set_key: ifindex=4 (uap0) alg=2 addr=0x99d80 key_idx=1 set_tx=1 seq_len=0 key_len=32
nl80211: KEY_DATA - hexdump(len=32): [REMOVED]
   broadcast key
nl80211: Set uap0 operstate 0->1 (UP)
netlink: Operstate: ifindex=4 linkmode=-1 (no change), operstate=6 (IF_OPER_UP) nl80211: TX queue param set: queue=0 aifs=1 cw_min=3 cw_max=7 burst_time=15 --> res=0 nl80211: TX queue param set: queue=1 aifs=1 cw_min=7 cw_max=15 burst_time=30 --> res=0 nl80211: TX queue param set: queue=2 aifs=3 cw_min=15 cw_max=63 burst_time=0 --> res=0 nl80211: TX queue param set: queue=3 aifs=7 cw_min=15 cw_max=1023 burst_time=0 --> res=0
nl80211: Set Deny ACL (num_mac_acl=0)
uap0: interface state UNINITIALIZED->ENABLED
uap0: AP-ENABLED
uap0: Setup of interface done.
ctrl_iface not configured!
RTM_NEWLINK: ifi_index=4 ifname=uap0 operstate=2 linkmode=0 master=6 ifi_family=0 ifi_flags=0x1003 ([UP]) RTM_NEWLINK: ifi_index=4 ifname=uap0 operstate=2 linkmode=0 master=6 ifi_family=0 ifi_flags=0x1003 ([UP]) RTM_NEWLINK: ifi_index=6 ifname=br0 operstate=3 linkmode=0 ifi_family=0 ifi_flags=0x1003 ([UP])
uap0: Event INTERFACE_STATUS (5) received
Unknown event 5
RTM_NEWLINK: ifi_index=4 ifname=uap0 master=6 operstate=2 ifi_family=7 ifi_flags=0x1003 ([UP])
nl80211: Add ifindex 6 for bridge br0
nl80211: Add own interface ifindex 6 (ifidx_reason 4)
nl80211: ifindex 6 already in the list
RTM_NEWLINK: ifi_index=6 ifname=br0 operstate=3 linkmode=0 ifi_family=0 ifi_flags=0x1003 ([UP])
uap0: Event INTERFACE_STATUS (5) received
Unknown event 5
RTM_NEWLINK: ifi_index=4 ifname=uap0 master=6 operstate=6 ifi_family=7 ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP])
nl80211: Add ifindex 6 for bridge br0
nl80211: Add own interface ifindex 6 (ifidx_reason 4)
nl80211: ifindex 6 already in the list
RTM_NEWLINK: ifi_index=4 ifname=uap0 master=6 operstate=6 ifi_family=7 ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP])
nl80211: Add ifindex 6 for bridge br0
nl80211: Add own interface ifindex 6 (ifidx_reason 4)
nl80211: ifindex 6 already in the list
RTM_NEWLINK: ifi_index=4 ifname=uap0 master=6 operstate=6 ifi_family=7 ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP])
nl80211: Add ifindex 6 for bridge br0
nl80211: Add own interface ifindex 6 (ifidx_reason 4)
nl80211: ifindex 6 already in the list
RTM_NEWLINK: ifi_index=4 ifname=uap0 operstate=6 linkmode=0 master=6 ifi_family=0 ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP]) RTM_NEWLINK: ifi_index=6 ifname=br0 operstate=6 linkmode=0 ifi_family=0 ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP])
uap0: Event INTERFACE_STATUS (5) received
Unknown event 5
RX ctrl_iface - hexdump_ascii(len=6):
     41 54 54 41 43 48 ATTACH
CTRL_IFACE monitor attached /tmp/wpa_ctrl_1029-1\x00
nl80211: Event message available
nl80211: BSS Event 59 (NL80211_CMD_FRAME) received for uap0
nl80211: MLME event 59 (NL80211_CMD_FRAME) on uap0(d4:ca:6e:6a:6a:59) A1=ff:ff:ff:ff:ff:ff A2=b8:e9:37:da:bb:95 nl80211: MLME event frame - hexdump(len=98): 40 00 00 00 ff ff ff ff ff ff b8 e9 37 da bb 95 ff ff ff ff ff ff 00 d8 00 20 53 6f 6e 6f 73 5f 74 51 4c 37 72 55 4b 4f 59 7a 46 73 6d 61 65 56 4f 56 6f 53 33 45 70 77 78 67 47 02 b7 00 4a 02 10 0b 4e 04 01 00 00 00 4b 04 a4 00 00 00 dd 12 00 0e 58 08 06 b8 e9 37 da bb 94 0f 02 08 01 09 01 01
nl80211: Frame event
nl80211: RX frame da=ff:ff:ff:ff:ff:ff sa=b8:e9:37:da:bb:95 bssid=ff:ff:ff:ff:ff:ff freq=2437 ssi_signal=0 fc=0x40 seq_ctrl=0xd800 stype=4 (WLAN_FC_STYPE_PROBE_REQ) len=98 STA b8:e9:37:da:bb:95 sent probe request without SSID or supported rates element
nl80211: Event message available
nl80211: BSS Event 59 (NL80211_CMD_FRAME) received for uap0
nl80211: MLME event 59 (NL80211_CMD_FRAME) on uap0(d4:ca:6e:6a:6a:59) A1=ff:ff:ff:ff:ff:ff A2=b8:e9:37:da:bb:95 nl80211: MLME event frame - hexdump(len=98): 40 00 00 00 ff ff ff ff ff ff b8 e9 37 da bb 95 ff ff ff ff ff ff 10 d8 00 20 53 6f 6e 6f 73 5f 74 51 4c 37 72 55 4b 4f 59 7a 46 73 6d 61 65 56 4f 56 6f 53 33 45 70 77 78 67 47 02 b8 00 4a 02 10 0b 4e 04 01 00 00 00 4b 04 a4 00 00 00 dd 12 00 0e 58 08 06 b8 e9 37 da bb 94 0f 02 08 01 09 01 01
nl80211: Frame event

.....

nl80211: RX frame da=ff:ff:ff:ff:ff:ff sa=b8:e9:37:da:bb:95 bssid=ff:ff:ff:ff:ff:ff freq=2437 ssi_signal=0 fc=0x40 seq_ctrl=0xd840 stype=4 (WLAN_FC_STYPE_PROBE_REQ) len=85
nl80211: Event message available
nl80211: BSS Event 59 (NL80211_CMD_FRAME) received for uap0
nl80211: MLME event 59 (NL80211_CMD_FRAME) on uap0(d4:ca:6e:6a:6a:59) A1=ff:ff:ff:ff:ff:ff A2=b8:e9:37:da:bb:94 nl80211: MLME event frame - hexdump(len=53): 40 00 00 00 ff ff ff ff ff ff b8 e9 37 da bb 94 ff ff ff ff ff ff 50 d8 00 00 01 04 02 04 0b 16 32 08 0c 12 18 24 30 48 60 6c 03 01 06 dd 06 00 0e 58 00 01 00
nl80211: Frame event
nl80211: RX frame da=ff:ff:ff:ff:ff:ff sa=b8:e9:37:da:bb:94 bssid=ff:ff:ff:ff:ff:ff freq=2437 ssi_signal=0 fc=0x40 seq_ctrl=0xd850 stype=4 (WLAN_FC_STYPE_PROBE_REQ) len=53 nl80211: send_mlme - da= b8:e9:37:da:bb:94 noack=1 freq=0 no_cck=0 offchanok=0 wait_time=0 fc=0x50 (WLAN_FC_STYPE_PROBE_RESP) nlmode=3
nl80211: Use bss->freq=2437
nl80211: CMD_FRAME freq=2437 wait=0 no_cck=0 no_ack=1 offchanok=0
CMD_FRAME - hexdump(len=95): 50 00 00 00 b8 e9 37 da bb 94 d4 ca 6e 6a 6a 59 d4 ca 6e 6a 6a 59 00 00 00 00 00 00 00 00 00 00 64 00 11 04 00 06 6d 79 73 73 69 64 01 08 82 84 8b 96 0c 12 18 24 03 01 06 2a 01 04 32 04 30 48 60 6c 30 14 01 00 00 0f ac 02 01 00 00 0f ac 02 01 00 00 0f ac 02 00 00 3b 02 51 00 7f 01 04
nl80211: Frame TX command accepted (no ACK); cookie 0x0
nl80211: Event message available
nl80211: BSS Event 59 (NL80211_CMD_FRAME) received for uap0
nl80211: MLME event 59 (NL80211_CMD_FRAME) on uap0(d4:ca:6e:6a:6a:59) A1=ff:ff:ff:ff:ff:ff A2=b8:e9:37:da:bb:94 nl80211: MLME event frame - hexdump(len=64): 40 00 00 00 ff ff ff ff ff ff b8 e9 37 da bb 94 ff ff ff ff ff ff 60 d8 00 0b 54 65 6c 73 74 72 61 30 37 43 38 01 04 02 04 0b 16 32 08 0c 12 18 24 30 48 60 6c 03 01 06 dd 06 00 0e 58 00 01 00
nl80211: Frame event
nl80211: RX frame da=ff:ff:ff:ff:ff:ff sa=b8:e9:37:da:bb:94 bssid=ff:ff:ff:ff:ff:ff freq=2437 ssi_signal=0 fc=0x40 seq_ctrl=0xd860 stype=4 (WLAN_FC_STYPE_PROBE_REQ) len=64
nl80211: Event message available
nl80211: BSS Event 59 (NL80211_CMD_FRAME) received for uap0
nl80211: MLME event 59 (NL80211_CMD_FRAME) on uap0(d4:ca:6e:6a:6a:59) A1=ff:ff:ff:ff:ff:ff A2=b8:e9:37:da:bb:95 nl80211: MLME event frame - hexdump(len=85): 40 00 00 00 ff ff ff ff ff ff b8 e9 37 da bb 95 ff ff ff ff ff ff 70 d8 00 20 53 6f 6e 6f 73 5f 74 51 4c 37 72 55 4b 4f 59 7a 46 73 6d 61 65 56 4f 56 6f 53 33 45 70 77 78 67 01 04 02 04 0b 16 32 08 0c 12 18 24 30 48 60 6c 03 01 06 dd 06 00 0e 58 00 01 00
nl80211: Frame event
nl80211: RX frame da=ff:ff:ff:ff:ff:ff sa=b8:e9:37:da:bb:95 bssid=ff:ff:ff:ff:ff:ff freq=2437 ssi_signal=0 fc=0x40 seq_ctrl=0xd870 stype=4 (WLAN_FC_STYPE_PROBE_REQ) len=85
nl80211: Event message available
nl80211: BSS Event 59 (NL80211_CMD_FRAME) received for uap0
nl80211: MLME event 59 (NL80211_CMD_FRAME) on uap0(d4:ca:6e:6a:6a:59) A1=ff:ff:ff:ff:ff:ff A2=b8:e9:37:da:bb:94 nl80211: MLME event frame - hexdump(len=53): 40 00 00 00 ff ff ff ff ff ff b8 e9 37 da bb 94 ff ff ff ff ff ff 80 d8 00 00 01 04 02 04 0b 16 32 08 0c 12 18 24 30 48 60 6c 03 01 06 dd 06 00 0e 58 00 01 00
nl80211: Frame event
nl80211: RX frame da=ff:ff:ff:ff:ff:ff sa=b8:e9:37:da:bb:94 bssid=ff:ff:ff:ff:ff:ff freq=2437 ssi_signal=0 fc=0x40 seq_ctrl=0xd880 stype=4 (WLAN_FC_STYPE_PROBE_REQ) len=53 nl80211: send_mlme - da= b8:e9:37:da:bb:94 noack=1 freq=0 no_cck=0 offchanok=0 wait_time=0 fc=0x50 (WLAN_FC_STYPE_PROBE_RESP) nlmode=3
nl80211: Use bss->freq=2437
nl80211: CMD_FRAME freq=2437 wait=0 no_cck=0 no_ack=1 offchanok=0
CMD_FRAME - hexdump(len=95): 50 00 00 00 b8 e9 37 da bb 94 d4 ca 6e 6a 6a 59 d4 ca 6e 6a 6a 59 00 00 00 00 00 00 00 00 00 00 64 00 11 04 00 06 6d 79 73 73 69 64 01 08 82 84 8b 96 0c 12 18 24 03 01 06 2a 01 04 32 04 30 48 60 6c 30 14 01 00 00 0f ac 02 01 00 00 0f ac 02 01 00 00 0f ac 02 00 00 3b 02 51 00 7f 01 04
nl80211: Frame TX command accepted (no ACK); cookie 0x0
nl80211: Event message available
nl80211: BSS Event 59 (NL80211_CMD_FRAME) received for uap0
nl80211: MLME event 59 (NL80211_CMD_FRAME) on uap0(d4:ca:6e:6a:6a:59) A1=ff:ff:ff:ff:ff:ff A2=b8:e9:37:da:bb:94 nl80211: MLME event frame - hexdump(len=53): 40 00 00 00 ff ff ff ff ff ff b8 e9 37 da bb 94 ff ff ff ff ff ff 80 d8 00 00 01 04 02 04 0b 16 32 08 0c 12 18 24 30 48 60 6c 03 01 06 dd 06 00 0e 58 00 01 00
nl80211: Frame event
nl80211: RX frame da=ff:ff:ff:ff:ff:ff sa=b8:e9:37:da:bb:94 bssid=ff:ff:ff:ff:ff:ff freq=2437 ssi_signal=0 fc=0x40 seq_ctrl=0xd880 stype=4 (WLAN_FC_STYPE_PROBE_REQ) len=53 nl80211: send_mlme - da= b8:e9:37:da:bb:94 noack=1 freq=0 no_cck=0 offchanok=0 wait_time=0 fc=0x50 (WLAN_FC_STYPE_PROBE_RESP) nlmode=3
nl80211: Use bss->freq=2437
nl80211: CMD_FRAME freq=2437 wait=0 no_cck=0 no_ack=1 offchanok=0
CMD_FRAME - hexdump(len=95): 50 00 00 00 b8 e9 37 da bb 94 d4 ca 6e 6a 6a 59 d4 ca 6e 6a 6a 59 00 00 00 00 00 00 00 00 00 00 64 00 11 04 00 06 6d 79 73 73 69 64 01 08 82 84 8b 96 0c 12 18 24 03 01 06 2a 01 04 32 04 30 48 60 6c 30 14 01 00 00 0f ac 02 01 00 00 0f ac 02 01 00 00 0f ac 02 00 00 3b 02 51 00 7f 01 04
nl80211: Frame TX command accepted (no ACK); cookie 0x0
RTM_NEWLINK: ifi_index=4 ifname=uap0 master=6 operstate=6 ifi_family=7 ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP])
nl80211: Add ifindex 6 for bridge br0
nl80211: Add own interface ifindex 6 (ifidx_reason 4)
nl80211: ifindex 6 already in the list
RTM_NEWLINK: ifi_index=4 ifname=uap0 operstate=6 linkmode=0 master=6 ifi_family=0 ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP])
nl80211: Event message available

......

nl80211: Frame event
nl80211: RX frame da=d4:ca:6e:6a:6a:59 sa=8c:83:e1:25:a8:d0 bssid=d4:ca:6e:6a:6a:59 freq=2437 ssi_signal=0 fc=0x40 seq_ctrl=0x9580 stype=4 (WLAN_FC_STYPE_PROBE_REQ) len=71 nl80211: send_mlme - da= 8c:83:e1:25:a8:d0 noack=0 freq=0 no_cck=0 offchanok=0 wait_time=0 fc=0x50 (WLAN_FC_STYPE_PROBE_RESP) nlmode=3
nl80211: Use bss->freq=2437
nl80211: CMD_FRAME freq=2437 wait=0 no_cck=0 no_ack=0 offchanok=0
CMD_FRAME - hexdump(len=95): 50 00 00 00 8c 83 e1 25 a8 d0 d4 ca 6e 6a 6a 59 d4 ca 6e 6a 6a 59 00 00 00 00 00 00 00 00 00 00 64 00 11 04 00 06 6d 79 73 73 69 64 01 08 82 84 8b 96 0c 12 18 24 03 01 06 2a 01 04 32 04 30 48 60 6c 30 14 01 00 00 0f ac 02 01 00 00 0f ac 02 01 00 00 0f ac 02 00 00 3b 02 51 00 7f 01 04
nl80211: Frame TX command accepted; cookie 0xbf02cdb8cf0ebd14
nl80211: Event message available
nl80211: BSS Event 59 (NL80211_CMD_FRAME) received for uap0
nl80211: MLME event 59 (NL80211_CMD_FRAME) on uap0(d4:ca:6e:6a:6a:59) A1=d4:ca:6e:6a:6a:59 A2=8c:83:e1:25:a8:d0 nl80211: MLME event frame - hexdump(len=30): b0 00 3a 01 d4 ca 6e 6a 6a 59 8c 83 e1 25 a8 d0 d4 ca 6e 6a 6a 59 90 95 00 00 01 00 00 00
nl80211: Frame event
nl80211: RX frame da=d4:ca:6e:6a:6a:59 sa=8c:83:e1:25:a8:d0 bssid=d4:ca:6e:6a:6a:59 freq=2437 ssi_signal=0 fc=0xb0 seq_ctrl=0x9590 stype=11 (WLAN_FC_STYPE_AUTH) len=30
uap0: Event RX_MGMT (18) received
mgmt::auth
authentication: STA=8c:83:e1:25:a8:d0 auth_alg=0 auth_transaction=1 status_code=0 wep=0 seq_ctrl=0x9590
  New STA
uap0: STA 8c:83:e1:25:a8:d0 IEEE 802.11: authentication OK (open system)
uap0: STA 8c:83:e1:25:a8:d0 MLME: MLME-AUTHENTICATE.indication(8c:83:e1:25:a8:d0, OPEN_SYSTEM) uap0: STA 8c:83:e1:25:a8:d0 MLME: MLME-DELETEKEYS.request(8c:83:e1:25:a8:d0) authentication reply: STA=8c:83:e1:25:a8:d0 auth_alg=0 auth_transaction=2 resp=0 (IE len=0) (dbg=handle-auth) nl80211: send_mlme - da= 8c:83:e1:25:a8:d0 noack=0 freq=0 no_cck=0 offchanok=0 wait_time=0 fc=0xb0 (WLAN_FC_STYPE_AUTH) nlmode=3
nl80211: Use bss->freq=2437
nl80211: CMD_FRAME freq=2437 wait=0 no_cck=0 no_ack=0 offchanok=0
CMD_FRAME - hexdump(len=30): b0 00 00 00 8c 83 e1 25 a8 d0 d4 ca 6e 6a 6a 59 d4 ca 6e 6a 6a 59 00 00 00 00 02 00 00 00
nl80211: Frame TX command accepted; cookie 0x48fde901
nl80211: Event message available
nl80211: BSS Event 59 (NL80211_CMD_FRAME) received for uap0
nl80211: MLME event 59 (NL80211_CMD_FRAME) on uap0(d4:ca:6e:6a:6a:59) A1=d4:ca:6e:6a:6a:59 A2=8c:83:e1:25:a8:d0 nl80211: MLME event frame - hexdump(len=71): 40 00 3a 01 d4 ca 6e 6a 6a 59 8c 83 e1 25 a8 d0 d4 ca 6e 6a 6a 59 80 95 00 06 6d 79 73 73 69 64 01 04 02 04 0b 16 32 08 0c 12 18 24 30 48 60 6c 03 01 06 dd 07 00 50 f2 08 00 00 00 7f 09 04 00 0a 02 01 00 00 00 80
nl80211: Frame event
nl80211: RX frame da=d4:ca:6e:6a:6a:59 sa=8c:83:e1:25:a8:d0 bssid=d4:ca:6e:6a:6a:59 freq=2437 ssi_signal=0 fc=0x40 seq_ctrl=0x9580 stype=4 (WLAN_FC_STYPE_PROBE_REQ) len=71 nl80211: send_mlme - da= 8c:83:e1:25:a8:d0 noack=0 freq=0 no_cck=0 offchanok=0 wait_time=0 fc=0x50 (WLAN_FC_STYPE_PROBE_RESP) nlmode=3
nl80211: Use bss->freq=2437
nl80211: CMD_FRAME freq=2437 wait=0 no_cck=0 no_ack=0 offchanok=0
CMD_FRAME - hexdump(len=95): 50 00 00 00 8c 83 e1 25 a8 d0 d4 ca 6e 6a 6a 59 d4 ca 6e 6a 6a 59 00 00 00 00 00 00 00 00 00 00 64 00 11 04 00 06 6d 79 73 73 69 64 01 08 82 84 8b 96 0c 12 18 24 03 01 06 2a 01 04 32 04 30 48 60 6c 30 14 01 00 00 0f ac 02 01 00 00 0f ac 02 01 00 00 0f ac 02 00 00 3b 02 51 00 7f 01 04
nl80211: Frame TX command accepted; cookie 0xbf02cdb8cf0ebcc4
RTM_NEWLINK: ifi_index=4 ifname=uap0 wext ifi_family=0 ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP])
nl80211: Event message available
nl80211: Drv Event 60 (NL80211_CMD_FRAME_TX_STATUS) received for uap0
nl80211: MLME event 60 (NL80211_CMD_FRAME_TX_STATUS) on uap0(d4:ca:6e:6a:6a:59) A1=8c:83:e1:25:a8:d0 A2=d4:ca:6e:6a:6a:59 nl80211: MLME event frame - hexdump(len=30): b0 00 00 00 8c 83 e1 25 a8 d0 d4 ca 6e 6a 6a 59 d4 ca 6e 6a 6a 59 00 00 00 00 02 00 00 00
nl80211: Frame TX status event
uap0: Event TX_STATUS (16) received
mgmt::auth cb


------ > why does it not connect here ?


uap0: STA 8c:83:e1:25:a8:d0 IEEE 802.11: authenticated
nl80211: Event message available
nl80211: Drv Event 20 (NL80211_CMD_DEL_STATION) received for uap0
nl80211: Delete station 8c:83:e1:25:a8:d0
uap0: Event DISASSOC (1) received
uap0: STA 8c:83:e1:25:a8:d0 IEEE 802.11: disassociated
nl80211: sta_remove -> DEL_STATION uap0 8c:83:e1:25:a8:d0 --> 0 (Success)
ap_free_sta: cancel ap_handle_timer for 8c:83:e1:25:a8:d0
nl80211: Event message available
nl80211: BSS Event 59 (NL80211_CMD_FRAME) received for uap0
nl80211: MLME event 59 (NL80211_CMD_FRAME) on uap0(d4:ca:6e:6a:6a:59) A1=ff:ff:ff:ff:ff:ff A2=b8:e9:37:da:bb:94 nl80211: MLME event frame - hexdump(len=53): 40 00 00 00 ff ff ff ff ff ff b8 e9 37 da bb 94 ff ff ff ff ff ff f0 dd 00 00 01 04 02 04 0b 16 32 08 0c 12 18 24 30 48 60 6c 03 01 06 dd 06 00 0e 58 00 01 00
nl80211: Frame event
nl80211: RX frame da=ff:ff:ff:ff:ff:ff sa=b8:e9:37:da:bb:94 bssid=ff:ff:ff:ff:ff:ff freq=2437 ssi_signal=0 fc=0x40 seq_ctrl=0xddf0 stype=4 (WLAN_FC_STYPE_PROBE_REQ) len=53 nl80211: send_mlme - da= b8:e9:37:da:bb:94 noack=1 freq=0 no_cck=0 offchanok=0 wait_time=0 fc=0x50 (WLAN_FC_STYPE_PROBE_RESP) nlmode=3
nl80211: Use bss->freq=2437
nl80211: CMD_FRAME freq=2437 wait=0 no_cck=0 no_ack=1 offchanok=0
CMD_FRAME - hexdump(len=95): 50 00 00 00 b8 e9 37 da bb 94 d4 ca 6e 6a 6a 59 d4 ca 6e 6a 6a 59 00 00 00 00 00 00 00 00 00 00 64 00 11 04 00 06 6d 79 73 73 69 64 01 08 82 84 8b 96 0c 12 18 24 03 01 06 2a 01 04 32 04 30 48 60 6c 30 14 01 00 00 0f ac 02 01 00 00 0f ac 02 01 00 00 0f ac 02 00 00 3b 02 51 00 7f 01 04
nl80211: Frame TX command accepted (no ACK); cookie 0x0
nl80211: Event message available
nl80211: BSS Event 59 (NL80211_CMD_FRAME) received for uap0
nl80211: MLME event 59 (NL80211_CMD_FRAME) on uap0(d4:ca:6e:6a:6a:59) A1=ff:ff:ff:ff:ff:ff A2=b8:e9:37:da:bb:94 nl80211: MLME event frame - hexdump(len=53): 40 00 00 00 ff ff ff ff ff ff b8 e9 37 da bb 94 ff ff ff ff ff ff f0 dd 00 00 01 04 02 04 0b 16 32 08 0c 12 18 24 30 48 60 6c 03 01 06 dd 06 00 0e 58 00 01 00
nl80211: Frame event
nl80211: RX frame da=ff:ff:ff:ff:ff:ff sa=b8:e9:37:da:bb:94 bssid=ff:ff:ff:ff:ff:ff freq=2437 ssi_signal=0 fc=0x40 seq_ctrl=0xddf0 stype=4 (WLAN_FC_STYPE_PROBE_REQ) len=53 nl80211: send_mlme - da= b8:e9:37:da:bb:94 noack=1 freq=0 no_cck=0 offchanok=0 wait_time=0 fc=0x50 (WLAN_FC_STYPE_PROBE_RESP) nlmode=3
nl80211: Use bss->freq=2437
nl80211: CMD_FRAME freq=2437 wait=0 no_cck=0 no_ack=1 offchanok=0
CMD_FRAME - hexdump(len=95): 50 00 00 00 b8 e9 37 da bb 94 d4 ca 6e 6a 6a 59 d4 ca 6e 6a 6a 59 00 00 00 00 00 00 00 00 00 00 64 00 11 04 00 06 6d 79 73 73 69 64 01 08 82 84 8b 96 0c 12 18 24 03 01 06 2a 01 04 32 04 30 48 60 6c 30 14 01 00 00 0f ac 02 01 00 00 0f ac 02 01 00 00 0f ac 02 00 00 3b 02 51 00 7f 01 04
nl80211: Frame TX command accepted (no ACK); cookie 0x0
nl80211: Event message available
nl80211: BSS Event 59 (NL80211_CMD_FRAME) received for uap0
nl80211: MLME event 59 (NL80211_CMD_FRAME) on uap0(d4:ca:6e:6a:6a:59) A1=ff:ff:ff:ff:ff:ff A2=b8:e9:37:da:bb:94 nl80211: MLME event frame - hexdump(len=64): 40 00 00 00 ff ff ff ff ff ff b8 e9 37 da bb 94 ff ff ff ff ff ff 00 de 00 0b 54 65 6c 73 74 72 61 30 37 43 38 01 04 02 04 0b 16 32 08 0c 12 18 24 30 48 60 6c 03 01 06 dd 06 00 0e 58 00 01 00
nl80211: Frame event
nl80211: RX frame da=ff:ff:ff:ff:ff:ff sa=b8:e9:37:da:bb:94 bssid=ff:ff:ff:ff:ff:ff freq=2437 ssi_signal=0 fc=0x40 seq_ctrl=0xde00 stype=4 (WLAN_FC_STYPE_PROBE_REQ) len=64
nl80211: Event......


_______________________________________________
Hostap mailing list
Hostap@xxxxxxxxxxxxxxxxxxx
http://lists.infradead.org/mailman/listinfo/hostap




[Index of Archives]     [Linux Wireless]     [Linux Kernel]     [ATH6KL]     [Linux Bluetooth]     [Linux Netdev]     [Kernel Newbies]     [IDE]     [Security]     [Git]     [Netfilter]     [Bugtraq]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Linux ATA RAID]     [Samba]     [Device Mapper]

  Powered by Linux