2017-02-25 8:59 GMT+01:00 Jouni Malinen <j@xxxxx>:
> On Thu, Feb 23, 2017 at 03:13:36PM +0100, Charlemagne Lasse wrote:
>> I found a weird problem in LEDE 17.01 with an ath9k device and
>> reported it at https://bugs.lede-project.org/index.php?do=details&task_id=550
>> . But it looks like it is a bug in hostapd/wpa_supplicant because I
>> cannot reproduce it when using authsae.
> Can you produce debug logs from both wpa_supplicant and hostapd for
> this?
Yes, here is the output from hostapd -ddddd (the STOP_AP happens after
starting WPA_SUPPLICANT):
nl80211: ssid - hexdump_ascii(len=8):
6d 65 73 68 65 64 41 50 meshedAP
nl80211: ssid - hexdump_ascii(len=8):
6d 65 73 68 65 64 41 50 meshedAP
RX ctrl_iface - hexdump_ascii(len=7):
53 54 4f 50 5f 41 50 STOP_AP
RX ctrl_iface - hexdump_ascii(len=7):
53 54 4f 50 5f 41 50 STOP_AP
The -ddddd output from wpa_supplicant is attached
wpa_supplicant v2.7-devel
Successfully initialized wpa_supplicant
Initializing interface 'mesh-2' conf '/var/run/wpa_supplicant-mesh-2.conf' driver 'nl80211' ctrl_interface '/var/run/wpa_supplicant' bridge 'br-lan'
Configuration file '/var/run/wpa_supplicant-mesh-2.conf' -> '/var/run/wpa_supplicant-mesh-2.conf'
Reading configuration file '/var/run/wpa_supplicant-mesh-2.conf'
Line: 3 - start of a new network block
ssid - hexdump_ascii(len=6):
6d 79 6d 65 73 68 mymesh
key_mgmt: 0x400
mode=5 (0x5)
frequency=2412 (0x96c)
PSK (ASCII passphrase) - hexdump_ascii(len=15): [REMOVED]
PSK (from passphrase) - hexdump(len=32): [REMOVED]
Priority group 0
id=0 ssid='mymesh'
nl80211: TDLS supported
nl80211: TDLS external setup
nl80211: Supported cipher 00-0f-ac:1
nl80211: Supported cipher 00-0f-ac:5
nl80211: Supported cipher 00-0f-ac:2
nl80211: Supported cipher 00-0f-ac:4
nl80211: Supported cipher 00-0f-ac:10
nl80211: Supported cipher 00-0f-ac:8
nl80211: Supported cipher 00-0f-ac:9
nl80211: Supported cipher 00-0f-ac:6
nl80211: Supported cipher 00-0f-ac:13
nl80211: Supported cipher 00-0f-ac:11
nl80211: Supported cipher 00-0f-ac:12
nl80211: Using driver-based off-channel TX
nl80211: Driver-advertised extended capabilities (default) - hexdump(len=8): 00 00 00 00 00 00 00 40
nl80211: Driver-advertised extended capabilities mask (default) - hexdump(len=8): 00 00 00 00 00 00 00 40
nl80211: Use separate P2P group interface (driver advertised support)
nl80211: interface mesh-2 in phy phy0
nl80211: Set mode ifindex 7 iftype 7 (MESH_POINT)
nl80211: Subscribe to mgmt frames with mesh handle 0x77d5aa60
nl80211: Register frame type=0xb0 (WLAN_FC_STYPE_AUTH) nl_handle=0x77d5aa60 match=
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x77d5aa60 match=0f01
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x77d5aa60 match=0f02
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x77d5aa60 match=0f03
netlink: Operstate: ifindex=7 linkmode=1 (userspace-control), operstate=5 (IF_OPER_DORMANT)
Add interface mesh-2 to a new radio phy0
nl80211: Regulatory information - country=US (DFS-FCC)
nl80211: 2402-2472 @ 40 MHz 30 mBm
nl80211: 5170-5250 @ 80 MHz 23 mBm
nl80211: 5250-5330 @ 80 MHz 23 mBm (DFS)
nl80211: 5490-5730 @ 160 MHz 23 mBm (DFS)
nl80211: 5735-5835 @ 80 MHz 30 mBm
nl80211: 57240-63720 @ 2160 MHz 40 mBm
nl80211: Added 802.11b mode based on 802.11g information
mesh-2: Own MAC address: ae:86:74:00:00:01
mesh-2: Receiving packets from bridge interface 'br-lan'
wpa_driver_nl80211_set_key: ifindex=7 (mesh-2) alg=0 addr=0 key_idx=0 set_tx=0 seq_len=0 key_len=0
wpa_driver_nl80211_set_key: ifindex=7 (mesh-2) alg=0 addr=0 key_idx=1 set_tx=0 seq_len=0 key_len=0
wpa_driver_nl80211_set_key: ifindex=7 (mesh-2) alg=0 addr=0 key_idx=2 set_tx=0 seq_len=0 key_len=0
wpa_driver_nl80211_set_key: ifindex=7 (mesh-2) alg=0 addr=0 key_idx=3 set_tx=0 seq_len=0 key_len=0
wpa_driver_nl80211_set_key: ifindex=7 (mesh-2) alg=0 addr=0 key_idx=4 set_tx=0 seq_len=0 key_len=0
wpa_driver_nl80211_set_key: ifindex=7 (mesh-2) alg=0 addr=0 key_idx=5 set_tx=0 seq_len=0 key_len=0
mesh-2: RSN: flushing PMKID list in the driver
nl80211: Flush PMKIDs
mesh-2: Setting scan request: 0.100000 sec
mesh-2: WPS: UUID based on MAC address: 741ed594-a0c3-50a5-8b47-6d63dd883d39
ENGINE: Loading dynamic engine
ENGINE: Loading dynamic engine
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: Supplicant port status: Unauthorized
nl80211: Skip set_supp_port(unauthorized) while not associated
EAPOL: KEY_RX entering state NO_KEY_RECEIVE
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
mesh-2: Added interface mesh-2
mesh-2: State: DISCONNECTED -> DISCONNECTED
nl80211: Set mesh-2 operstate 0->0 (DORMANT)
netlink: Operstate: ifindex=7 linkmode=-1 (no change), operstate=5 (IF_OPER_DORMANT)
mesh-2: State: DISCONNECTED -> SCANNING
mesh-2: Starting AP scan for wildcard SSID
mesh-2: Add radio work 'scan'@0x77d42870
mesh-2: First radio work item in the queue - schedule start immediately
RTM_NEWLINK: ifi_index=7 ifname=mesh-2 master=5 operstate=33554432 ifi_family=7 ifi_flags=0x1003 ([UP])
nl80211: Add ifindex 5 for bridge br-lan
nl80211: Add own interface ifindex 5 (ifidx_reason 7)
nl80211: if_indices[16]: 5(7)
RTM_NEWLINK: ifi_index=7 ifname=mesh-2 operstate=33554432 linkmode=16777216 master=5 ifi_family=0 ifi_flags=0x1003 ([UP])
mesh-2: Starting radio work 'scan'@0x77d42870 after 0.003195 second wait
mesh-2: nl80211: scan request
nl80211: Scan SSID - hexdump_ascii(len=0): [NULL]
nl80211: Scan extra IEs - hexdump(len=12): 7f 08 00 00 00 00 00 00 00 40 72 00
Scan requested (ret=0) - scan timeout 10 seconds
nl80211: Event message available
nl80211: Drv Event 33 (NL80211_CMD_TRIGGER_SCAN) received for mesh-2
mesh-2: nl80211: Scan trigger
mesh-2: Event SCAN_STARTED (47) received
mesh-2: Own scan request started a scan in 0.003734 seconds
RTM_NEWLINK: ifi_index=7 ifname=mesh-2 wext ifi_family=0 ifi_flags=0x1003 ([UP])
nl80211: Event message available
nl80211: Drv Event 34 (NL80211_CMD_NEW_SCAN_RESULTS) received for mesh-2
mesh-2: nl80211: New scan results available
nl80211: Scan probed for SSID ''
nl80211: Scan included frequencies: 2412 2417 2422 2427 2432 2437 2442 2447 2452 2457 2462
mesh-2: Event SCAN_RESULTS (3) received
mesh-2: Scan completed in 0.651049 seconds
nl80211: Received scan results (0 BSSes)
Sorted scan results
BSS: last_scan_res_used=0/32
mesh-2: New scan results available (own=1 ext=0)
mesh-2: Radio work 'scan'@0x77d42870 done in 0.714678 seconds
mesh-2: radio_work_free('scan'@0x77d42870: num_active_works --> 0
mesh-2: Selecting BSS from priority group 0
mesh-2: No suitable network found
mesh-2: Setup a new network
phy: phy0
BSS count 1, BSSID mask 00:00:00:00:00:00 (0 bits)
nl80211: Regulatory information - country=US (DFS-FCC)
nl80211: 2402-2472 @ 40 MHz 30 mBm
nl80211: 5170-5250 @ 80 MHz 23 mBm
nl80211: 5250-5330 @ 80 MHz 23 mBm (DFS)
nl80211: 5490-5730 @ 160 MHz 23 mBm (DFS)
nl80211: 5735-5835 @ 80 MHz 30 mBm
nl80211: 57240-63720 @ 2160 MHz 40 mBm
nl80211: Added 802.11b mode based on 802.11g information
Allowed channel: mode=1 chan=1 freq=2412 MHz max_tx_power=30 dBm
Allowed channel: mode=1 chan=2 freq=2417 MHz max_tx_power=30 dBm
Allowed channel: mode=1 chan=3 freq=2422 MHz max_tx_power=30 dBm
Allowed channel: mode=1 chan=4 freq=2427 MHz max_tx_power=30 dBm
Allowed channel: mode=1 chan=5 freq=2432 MHz max_tx_power=30 dBm
Allowed channel: mode=1 chan=6 freq=2437 MHz max_tx_power=30 dBm
Allowed channel: mode=1 chan=7 freq=2442 MHz max_tx_power=30 dBm
Allowed channel: mode=1 chan=8 freq=2447 MHz max_tx_power=30 dBm
Allowed channel: mode=1 chan=9 freq=2452 MHz max_tx_power=30 dBm
Allowed channel: mode=1 chan=10 freq=2457 MHz max_tx_power=30 dBm
Allowed channel: mode=1 chan=11 freq=2462 MHz max_tx_power=30 dBm
Allowed channel: mode=0 chan=1 freq=2412 MHz max_tx_power=30 dBm
Allowed channel: mode=0 chan=2 freq=2417 MHz max_tx_power=30 dBm
Allowed channel: mode=0 chan=3 freq=2422 MHz max_tx_power=30 dBm
Allowed channel: mode=0 chan=4 freq=2427 MHz max_tx_power=30 dBm
Allowed channel: mode=0 chan=5 freq=2432 MHz max_tx_power=30 dBm
Allowed channel: mode=0 chan=6 freq=2437 MHz max_tx_power=30 dBm
Allowed channel: mode=0 chan=7 freq=2442 MHz max_tx_power=30 dBm
Allowed channel: mode=0 chan=8 freq=2447 MHz max_tx_power=30 dBm
Allowed channel: mode=0 chan=9 freq=2452 MHz max_tx_power=30 dBm
Allowed channel: mode=0 chan=10 freq=2457 MHz max_tx_power=30 dBm
Allowed channel: mode=0 chan=11 freq=2462 MHz max_tx_power=30 dBm
Completing interface initialization
Mode: IEEE 802.11g Channel: 1 Frequency: 2412 MHz
DFS 0 channels required radar detection
mesh-2: Mesh configuration will be applied while joining the mesh network
RATE[0] rate=10 flags=0x1
RATE[1] rate=20 flags=0x1
RATE[2] rate=55 flags=0x1
RATE[3] rate=110 flags=0x1
RATE[4] rate=60 flags=0x1
RATE[5] rate=90 flags=0x0
RATE[6] rate=120 flags=0x1
RATE[7] rate=180 flags=0x0
RATE[8] rate=240 flags=0x1
RATE[9] rate=360 flags=0x0
RATE[10] rate=480 flags=0x0
RATE[11] rate=540 flags=0x0
hostapd_setup_bss(hapd=0xcc2730 (mesh-2), first=1)
Flushing old station entries
nl80211: flush -> DEL_STATION mesh-2 (all)
Deauthenticate all stations
wpa_driver_nl80211_set_key: ifindex=7 (mesh-2) alg=0 addr=0 key_idx=0 set_tx=0 seq_len=0 key_len=0
wpa_driver_nl80211_set_key: ifindex=7 (mesh-2) alg=0 addr=0 key_idx=1 set_tx=0 seq_len=0 key_len=0
wpa_driver_nl80211_set_key: ifindex=7 (mesh-2) alg=0 addr=0 key_idx=2 set_tx=0 seq_len=0 key_len=0
wpa_driver_nl80211_set_key: ifindex=7 (mesh-2) alg=0 addr=0 key_idx=3 set_tx=0 seq_len=0 key_len=0
Using interface mesh-2 with hwaddr ae:86:74:00:00:01 and ssid ""
VLAN: vlan_set_name_type(name_type=2)
nl80211: Set mesh-2 operstate 0->1 (UP)
netlink: Operstate: ifindex=7 linkmode=-1 (no change), operstate=6 (IF_OPER_UP)
Failed to set TX queue parameters for queue 0.
Failed to set TX queue parameters for queue 1.
Failed to set TX queue parameters for queue 2.
Failed to set TX queue parameters for queue 3.
mesh-2: interface state UNINITIALIZED->ENABLED
AP-ENABLED
mesh-2: Setup of interface done.
nl80211: Set mode ifindex 7 iftype 7 (MESH_POINT)
nl80211: Unsubscribe mgmt frames handle 0xff5d22e9 (mode change)
nl80211: Subscribe to mgmt frames with mesh handle 0x77d5aa60
nl80211: Register frame type=0xb0 (WLAN_FC_STYPE_AUTH) nl_handle=0x77d5aa60 match=
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x77d5aa60 match=0f01
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x77d5aa60 match=0f02
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x77d5aa60 match=0f03
AUTH: Initializing group state machine
GMK - hexdump(len=32): [REMOVED]
Key Counter - hexdump(len=32): [REMOVED]
WPA: Delay group state machine start until Beacon frames have been configured
ELOOP: Too long timeout (secs=4294967295) to ever happen - ignore it
mesh: Own TX MGTK - hexdump(len=16): [REMOVED]
wpa_driver_nl80211_set_key: ifindex=7 (mesh-2) alg=3 addr=0 key_idx=1 set_tx=1 seq_len=6 key_len=16
nl80211: KEY_DATA - hexdump(len=16): [REMOVED]
nl80211: KEY_SEQ - hexdump(len=6): 00 00 00 00 00 00
mesh-2: joining mesh mymesh
nl80211: mesh join (ifindex=7)
* freq=2412
* vht_enabled=0
* ht_enabled=1
* sec_channel_offset=0
* channel_type=1wpa_supplicant v2.7-devel
Successfully initialized wpa_supplicant
Initializing interface 'mesh-2' conf '/var/run/wpa_supplicant-mesh-2.conf' driver 'nl80211' ctrl_interface '/var/run/wpa_supplicant' bridge 'br-lan'
Configuration file '/var/run/wpa_supplicant-mesh-2.conf' -> '/var/run/wpa_supplicant-mesh-2.conf'
Reading configuration file '/var/run/wpa_supplicant-mesh-2.conf'
Line: 3 - start of a new network block
ssid - hexdump_ascii(len=6):
6d 79 6d 65 73 68 mymesh
key_mgmt: 0x400
mode=5 (0x5)
frequency=2412 (0x96c)
PSK (ASCII passphrase) - hexdump_ascii(len=15): [REMOVED]
PSK (from passphrase) - hexdump(len=32): [REMOVED]
Priority group 0
id=0 ssid='mymesh'
nl80211: TDLS supported
nl80211: TDLS external setup
nl80211: Supported cipher 00-0f-ac:1
nl80211: Supported cipher 00-0f-ac:5
nl80211: Supported cipher 00-0f-ac:2
nl80211: Supported cipher 00-0f-ac:4
nl80211: Supported cipher 00-0f-ac:10
nl80211: Supported cipher 00-0f-ac:8
nl80211: Supported cipher 00-0f-ac:9
nl80211: Supported cipher 00-0f-ac:6
nl80211: Supported cipher 00-0f-ac:13
nl80211: Supported cipher 00-0f-ac:11
nl80211: Supported cipher 00-0f-ac:12
nl80211: Using driver-based off-channel TX
nl80211: Driver-advertised extended capabilities (default) - hexdump(len=8): 00 00 00 00 00 00 00 40
nl80211: Driver-advertised extended capabilities mask (default) - hexdump(len=8): 00 00 00 00 00 00 00 40
nl80211: Use separate P2P group interface (driver advertised support)
nl80211: interface mesh-2 in phy phy0
nl80211: Set mode ifindex 7 iftype 7 (MESH_POINT)
nl80211: Subscribe to mgmt frames with mesh handle 0x77d5aa60
nl80211: Register frame type=0xb0 (WLAN_FC_STYPE_AUTH) nl_handle=0x77d5aa60 match=
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x77d5aa60 match=0f01
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x77d5aa60 match=0f02
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x77d5aa60 match=0f03
netlink: Operstate: ifindex=7 linkmode=1 (userspace-control), operstate=5 (IF_OPER_DORMANT)
Add interface mesh-2 to a new radio phy0
nl80211: Regulatory information - country=US (DFS-FCC)
nl80211: 2402-2472 @ 40 MHz 30 mBm
nl80211: 5170-5250 @ 80 MHz 23 mBm
nl80211: 5250-5330 @ 80 MHz 23 mBm (DFS)
nl80211: 5490-5730 @ 160 MHz 23 mBm (DFS)
nl80211: 5735-5835 @ 80 MHz 30 mBm
nl80211: 57240-63720 @ 2160 MHz 40 mBm
nl80211: Added 802.11b mode based on 802.11g information
mesh-2: Own MAC address: ae:86:74:00:00:01
mesh-2: Receiving packets from bridge interface 'br-lan'
wpa_driver_nl80211_set_key: ifindex=7 (mesh-2) alg=0 addr=0 key_idx=0 set_tx=0 seq_len=0 key_len=0
wpa_driver_nl80211_set_key: ifindex=7 (mesh-2) alg=0 addr=0 key_idx=1 set_tx=0 seq_len=0 key_len=0
wpa_driver_nl80211_set_key: ifindex=7 (mesh-2) alg=0 addr=0 key_idx=2 set_tx=0 seq_len=0 key_len=0
wpa_driver_nl80211_set_key: ifindex=7 (mesh-2) alg=0 addr=0 key_idx=3 set_tx=0 seq_len=0 key_len=0
wpa_driver_nl80211_set_key: ifindex=7 (mesh-2) alg=0 addr=0 key_idx=4 set_tx=0 seq_len=0 key_len=0
wpa_driver_nl80211_set_key: ifindex=7 (mesh-2) alg=0 addr=0 key_idx=5 set_tx=0 seq_len=0 key_len=0
mesh-2: RSN: flushing PMKID list in the driver
nl80211: Flush PMKIDs
mesh-2: Setting scan request: 0.100000 sec
mesh-2: WPS: UUID based on MAC address: 741ed594-a0c3-50a5-8b47-6d63dd883d39
ENGINE: Loading dynamic engine
ENGINE: Loading dynamic engine
EAPOL: SUPP_PAE entering state DISCONNECTED
EAPOL: Supplicant port status: Unauthorized
nl80211: Skip set_supp_port(unauthorized) while not associated
EAPOL: KEY_RX entering state NO_KEY_RECEIVE
EAPOL: SUPP_BE entering state INITIALIZE
EAP: EAP entering state DISABLED
mesh-2: Added interface mesh-2
mesh-2: State: DISCONNECTED -> DISCONNECTED
nl80211: Set mesh-2 operstate 0->0 (DORMANT)
netlink: Operstate: ifindex=7 linkmode=-1 (no change), operstate=5 (IF_OPER_DORMANT)
mesh-2: State: DISCONNECTED -> SCANNING
mesh-2: Starting AP scan for wildcard SSID
mesh-2: Add radio work 'scan'@0x77d42870
mesh-2: First radio work item in the queue - schedule start immediately
RTM_NEWLINK: ifi_index=7 ifname=mesh-2 master=5 operstate=33554432 ifi_family=7 ifi_flags=0x1003 ([UP])
nl80211: Add ifindex 5 for bridge br-lan
nl80211: Add own interface ifindex 5 (ifidx_reason 7)
nl80211: if_indices[16]: 5(7)
RTM_NEWLINK: ifi_index=7 ifname=mesh-2 operstate=33554432 linkmode=16777216 master=5 ifi_family=0 ifi_flags=0x1003 ([UP])
mesh-2: Starting radio work 'scan'@0x77d42870 after 0.003195 second wait
mesh-2: nl80211: scan request
nl80211: Scan SSID - hexdump_ascii(len=0): [NULL]
nl80211: Scan extra IEs - hexdump(len=12): 7f 08 00 00 00 00 00 00 00 40 72 00
Scan requested (ret=0) - scan timeout 10 seconds
nl80211: Event message available
nl80211: Drv Event 33 (NL80211_CMD_TRIGGER_SCAN) received for mesh-2
mesh-2: nl80211: Scan trigger
mesh-2: Event SCAN_STARTED (47) received
mesh-2: Own scan request started a scan in 0.003734 seconds
RTM_NEWLINK: ifi_index=7 ifname=mesh-2 wext ifi_family=0 ifi_flags=0x1003 ([UP])
nl80211: Event message available
nl80211: Drv Event 34 (NL80211_CMD_NEW_SCAN_RESULTS) received for mesh-2
mesh-2: nl80211: New scan results available
nl80211: Scan probed for SSID ''
nl80211: Scan included frequencies: 2412 2417 2422 2427 2432 2437 2442 2447 2452 2457 2462
mesh-2: Event SCAN_RESULTS (3) received
mesh-2: Scan completed in 0.651049 seconds
nl80211: Received scan results (0 BSSes)
Sorted scan results
mesh-2: BSS: Start scan result update 0
BSS: last_scan_res_used=0/32
mesh-2: No suitable network found
mesh-2: Setup a new network
phy: phy0
BSS count 1, BSSID mask 00:00:00:00:00:00 (0 bits)
nl80211: Regulatory information - country=US (DFS-FCC)
nl80211: 2402-2472 @ 40 MHz 30 mBm
nl80211: 5170-5250 @ 80 MHz 23 mBm
nl80211: 5250-5330 @ 80 MHz 23 mBm (DFS)
nl80211: 5490-5730 @ 160 MHz 23 mBm (DFS)
nl80211: 5735-5835 @ 80 MHz 30 mBm
nl80211: 57240-63720 @ 2160 MHz 40 mBm
nl80211: Added 802.11b mode based on 802.11g information
Allowed channel: mode=1 chan=1 freq=2412 MHz max_tx_power=30 dBm
Allowed channel: mode=1 chan=2 freq=2417 MHz max_tx_power=30 dBm
Allowed channel: mode=1 chan=3 freq=2422 MHz max_tx_power=30 dBm
Allowed channel: mode=1 chan=4 freq=2427 MHz max_tx_power=30 dBm
Allowed channel: mode=1 chan=5 freq=2432 MHz max_tx_power=30 dBm
Allowed channel: mode=1 chan=6 freq=2437 MHz max_tx_power=30 dBm
Allowed channel: mode=1 chan=7 freq=2442 MHz max_tx_power=30 dBm
Allowed channel: mode=1 chan=8 freq=2447 MHz max_tx_power=30 dBm
Allowed channel: mode=1 chan=9 freq=2452 MHz max_tx_power=30 dBm
Allowed channel: mode=1 chan=10 freq=2457 MHz max_tx_power=30 dBm
Allowed channel: mode=1 chan=11 freq=2462 MHz max_tx_power=30 dBm
Allowed channel: mode=0 chan=1 freq=2412 MHz max_tx_power=30 dBm
Allowed channel: mode=0 chan=2 freq=2417 MHz max_tx_power=30 dBm
Allowed channel: mode=0 chan=3 freq=2422 MHz max_tx_power=30 dBm
Allowed channel: mode=0 chan=4 freq=2427 MHz max_tx_power=30 dBm
Allowed channel: mode=0 chan=5 freq=2432 MHz max_tx_power=30 dBm
Allowed channel: mode=0 chan=6 freq=2437 MHz max_tx_power=30 dBm
Allowed channel: mode=0 chan=7 freq=2442 MHz max_tx_power=30 dBm
Allowed channel: mode=0 chan=8 freq=2447 MHz max_tx_power=30 dBm
Allowed channel: mode=0 chan=9 freq=2452 MHz max_tx_power=30 dBm
Allowed channel: mode=0 chan=10 freq=2457 MHz max_tx_power=30 dBm
Allowed channel: mode=0 chan=11 freq=2462 MHz max_tx_power=30 dBm
Completing interface initialization
Mode: IEEE 802.11g Channel: 1 Frequency: 2412 MHz
DFS 0 channels required radar detection
mesh-2: Mesh configuration will be applied while joining the mesh network
RATE[0] rate=10 flags=0x1
RATE[1] rate=20 flags=0x1
RATE[2] rate=55 flags=0x1
RATE[3] rate=110 flags=0x1
RATE[4] rate=60 flags=0x1
RATE[5] rate=90 flags=0x0
RATE[6] rate=120 flags=0x1
RATE[7] rate=180 flags=0x0
RATE[8] rate=240 flags=0x1
RATE[9] rate=360 flags=0x0
RATE[10] rate=480 flags=0x0
RATE[11] rate=540 flags=0x0
hostapd_setup_bss(hapd=0xcc2730 (mesh-2), first=1)
Flushing old station entries
nl80211: flush -> DEL_STATION mesh-2 (all)
Deauthenticate all stations
wpa_driver_nl80211_set_key: ifindex=7 (mesh-2) alg=0 addr=0 key_idx=0 set_tx=0 seq_len=0 key_len=0
wpa_driver_nl80211_set_key: ifindex=7 (mesh-2) alg=0 addr=0 key_idx=1 set_tx=0 seq_len=0 key_len=0
wpa_driver_nl80211_set_key: ifindex=7 (mesh-2) alg=0 addr=0 key_idx=2 set_tx=0 seq_len=0 key_len=0
wpa_driver_nl80211_set_key: ifindex=7 (mesh-2) alg=0 addr=0 key_idx=3 set_tx=0 seq_len=0 key_len=0
Using interface mesh-2 with hwaddr ae:86:74:00:00:01 and ssid ""
VLAN: vlan_set_name_type(name_type=2)
nl80211: Set mesh-2 operstate 0->1 (UP)
netlink: Operstate: ifindex=7 linkmode=-1 (no change), operstate=6 (IF_OPER_UP)
Failed to set TX queue parameters for queue 0.
Failed to set TX queue parameters for queue 1.
Failed to set TX queue parameters for queue 2.
Failed to set TX queue parameters for queue 3.
mesh-2: interface state UNINITIALIZED->ENABLED
AP-ENABLED
mesh-2: Setup of interface done.
nl80211: Set mode ifindex 7 iftype 7 (MESH_POINT)
nl80211: Unsubscribe mgmt frames handle 0xff5d22e9 (mode change)
nl80211: Subscribe to mgmt frames with mesh handle 0x77d5aa60
nl80211: Register frame type=0xb0 (WLAN_FC_STYPE_AUTH) nl_handle=0x77d5aa60 match=
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x77d5aa60 match=0f01
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x77d5aa60 match=0f02
nl80211: Register frame type=0xd0 (WLAN_FC_STYPE_ACTION) nl_handle=0x77d5aa60 match=0f03
AUTH: Initializing group state machine
GMK - hexdump(len=32): [REMOVED]
Key Counter - hexdump(len=32): [REMOVED]
WPA: Delay group state machine start until Beacon frames have been configured
ELOOP: Too long timeout (secs=4294967295) to ever happen - ignore it
mesh: Own TX MGTK - hexdump(len=16): [REMOVED]
wpa_driver_nl80211_set_key: ifindex=7 (mesh-2) alg=3 addr=0 key_idx=1 set_tx=1 seq_len=6 key_len=16
nl80211: KEY_DATA - hexdump(len=16): [REMOVED]
nl80211: KEY_SEQ - hexdump(len=6): 00 00 00 00 00 00
mesh-2: joining mesh mymesh
nl80211: mesh join (ifindex=7)
* freq=2412
* vht_enabled=0
* ht_enabled=1
* sec_channel_offset=0
* channel_type=1
* Mesh ID (SSID) - hexdump_ascii(len=6):
6d 79 6d 65 73 68 mymesh
* flags=0000000D
* IEs - hexdump(len=22): 30 14 01 00 00 0f ac 04 01 00 00 0f ac 04 01 00 00 0f ac 08 00 00
nl80211: mesh join request send successfully
nl80211: Set mesh-2 operstate 1->1 (UP)
netlink: Operstate: ifindex=7 linkmode=-1 (no change), operstate=6 (IF_OPER_UP)
mesh-2: State: SCANNING -> COMPLETED
mesh-2: CTRL-EVENT-CONNECTED - Connection to 00:00:00:00:00:00 completed [id=0 id_str=]
nl80211: Set mesh-2 operstate 1->1 (UP)
netlink: Operstate: ifindex=7 linkmode=-1 (no change), operstate=6 (IF_OPER_UP)
mesh-2: MESH-GROUP-STARTED ssid="mymesh" id=0
RTM_NEWLINK: ifi_index=7 ifname=mesh-2 master=5 operstate=83886080 ifi_family=7 ifi_flags=0x11003 ([UP][LOWER_UP])
nl80211: Set IF_OPER_UP again based on ifi_flags and expected operstate
netlink: Operstate: ifindex=7 linkmode=-1 (no change), operstate=6 (IF_OPER_UP)
nl80211: Add ifindex 5 for bridge br-lan
nl80211: Add own interface ifindex 5 (ifidx_reason 7)
nl80211: ifindex 5 already in the list
RTM_NEWLINK: ifi_index=7 ifname=mesh-2 operstate=83886080 linkmode=16777216 master=5 ifi_family=0 ifi_flags=0x11003 ([UP][LOWER_UP])
nl80211: Set IF_OPER_UP again based on ifi_flags and expected operstate
netlink: Operstate: ifindex=7 linkmode=-1 (no change), operstate=6 (IF_OPER_UP)
RTM_NEWLINK: ifi_index=7 ifname=mesh-2 master=5 operstate=100663296 ifi_family=7 ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP])
nl80211: Add ifindex 5 for bridge br-lan
nl80211: Add own interface ifindex 5 (ifidx_reason 7)
nl80211: ifindex 5 already in the list
RTM_NEWLINK: ifi_index=7 ifname=mesh-2 master=5 operstate=100663296 ifi_family=7 ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP])
nl80211: Add ifindex 5 for bridge br-lan
nl80211: Add own interface ifindex 5 (ifidx_reason 7)
nl80211: ifindex 5 already in the list
RTM_NEWLINK: ifi_index=7 ifname=mesh-2 master=5 operstate=100663296 ifi_family=7 ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP])
nl80211: Add ifindex 5 for bridge br-lan
nl80211: Add own interface ifindex 5 (ifidx_reason 7)
nl80211: ifindex 5 already in the list
RTM_NEWLINK: ifi_index=7 ifname=mesh-2 operstate=100663296 linkmode=16777216 master=5 ifi_family=0 ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP])
VLAN: RTM_NEWLINK: ifi_index=7 ifname=mesh-2 ifi_family=7 ifi_flags=0x11003 ([UP][LOWER_UP])
VLAN: vlan_newlink(mesh-2)
VLAN: RTM_NEWLINK: ifi_index=7 ifname=mesh-2 ifi_family=0 ifi_flags=0x11003 ([UP][LOWER_UP])
VLAN: vlan_newlink(mesh-2)
VLAN: RTM_NEWLINK: ifi_index=7 ifname=mesh-2 ifi_family=7 ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP])
VLAN: vlan_newlink(mesh-2)
VLAN: RTM_NEWLINK: ifi_index=7 ifname=mesh-2 ifi_family=7 ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP])
VLAN: vlan_newlink(mesh-2)
VLAN: RTM_NEWLINK: ifi_index=7 ifname=mesh-2 ifi_family=7 ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP])
VLAN: vlan_newlink(mesh-2)
VLAN: RTM_NEWLINK: ifi_index=7 ifname=mesh-2 ifi_family=0 ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP])
VLAN: vlan_newlink(mesh-2)
EAPOL: disable timer tick
RTM_NEWLINK: ifi_index=7 ifname=mesh-2 master=5 operstate=100663296 ifi_family=7 ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP])
nl80211: Add ifindex 5 for bridge br-lan
nl80211: Add own interface ifindex 5 (ifidx_reason 7)
nl80211: ifindex 5 already in the list
VLAN: RTM_NEWLINK: ifi_index=7 ifname=mesh-2 ifi_family=7 ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP])
VLAN: vlan_newlink(mesh-2)
* Mesh ID (SSID) - hexdump_ascii(len=6):
6d 79 6d 65 73 68 mymesh
* flags=0000000D
* IEs - hexdump(len=22): 30 14 01 00 00 0f ac 04 01 00 00 0f ac 04 01 00 00 0f ac 08 00 00
nl80211: mesh join request send successfully
nl80211: Set mesh-2 operstate 1->1 (UP)
netlink: Operstate: ifindex=7 linkmode=-1 (no change), operstate=6 (IF_OPER_UP)
mesh-2: State: SCANNING -> COMPLETED
mesh-2: CTRL-EVENT-CONNECTED - Connection to 00:00:00:00:00:00 completed [id=0 id_str=]
nl80211: Set mesh-2 operstate 1->1 (UP)
netlink: Operstate: ifindex=7 linkmode=-1 (no change), operstate=6 (IF_OPER_UP)
mesh-2: MESH-GROUP-STARTED ssid="mymesh" id=0
RTM_NEWLINK: ifi_index=7 ifname=mesh-2 master=5 operstate=83886080 ifi_family=7 ifi_flags=0x11003 ([UP][LOWER_UP])
nl80211: Set IF_OPER_UP again based on ifi_flags and expected operstate
netlink: Operstate: ifindex=7 linkmode=-1 (no change), operstate=6 (IF_OPER_UP)
nl80211: Add ifindex 5 for bridge br-lan
nl80211: Add own interface ifindex 5 (ifidx_reason 7)
nl80211: ifindex 5 already in the list
RTM_NEWLINK: ifi_index=7 ifname=mesh-2 operstate=83886080 linkmode=16777216 master=5 ifi_family=0 ifi_flags=0x11003 ([UP][LOWER_UP])
nl80211: Set IF_OPER_UP again based on ifi_flags and expected operstate
netlink: Operstate: ifindex=7 linkmode=-1 (no change), operstate=6 (IF_OPER_UP)
RTM_NEWLINK: ifi_index=7 ifname=mesh-2 master=5 operstate=100663296 ifi_family=7 ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP])
nl80211: Add ifindex 5 for bridge br-lan
nl80211: Add own interface ifindex 5 (ifidx_reason 7)
nl80211: ifindex 5 already in the list
RTM_NEWLINK: ifi_index=7 ifname=mesh-2 master=5 operstate=100663296 ifi_family=7 ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP])
nl80211: Add ifindex 5 for bridge br-lan
nl80211: Add own interface ifindex 5 (ifidx_reason 7)
nl80211: ifindex 5 already in the list
RTM_NEWLINK: ifi_index=7 ifname=mesh-2 master=5 operstate=100663296 ifi_family=7 ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP])
nl80211: Add ifindex 5 for bridge br-lan
nl80211: Add own interface ifindex 5 (ifidx_reason 7)
nl80211: ifindex 5 already in the list
RTM_NEWLINK: ifi_index=7 ifname=mesh-2 operstate=100663296 linkmode=16777216 master=5 ifi_family=0 ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP])
VLAN: RTM_NEWLINK: ifi_index=7 ifname=mesh-2 ifi_family=7 ifi_flags=0x11003 ([UP][LOWER_UP])
VLAN: vlan_newlink(mesh-2)
VLAN: RTM_NEWLINK: ifi_index=7 ifname=mesh-2 ifi_family=0 ifi_flags=0x11003 ([UP][LOWER_UP])
VLAN: vlan_newlink(mesh-2)
VLAN: RTM_NEWLINK: ifi_index=7 ifname=mesh-2 ifi_family=7 ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP])
VLAN: vlan_newlink(mesh-2)
VLAN: RTM_NEWLINK: ifi_index=7 ifname=mesh-2 ifi_family=7 ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP])
VLAN: vlan_newlink(mesh-2)
VLAN: RTM_NEWLINK: ifi_index=7 ifname=mesh-2 ifi_family=7 ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP])
VLAN: vlan_newlink(mesh-2)
VLAN: RTM_NEWLINK: ifi_index=7 ifname=mesh-2 ifi_family=0 ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP])
VLAN: vlan_newlink(mesh-2)
EAPOL: disable timer tick
RTM_NEWLINK: ifi_index=7 ifname=mesh-2 master=5 operstate=100663296 ifi_family=7 ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP])
nl80211: Add ifindex 5 for bridge br-lan
nl80211: Add own interface ifindex 5 (ifidx_reason 7)
nl80211: ifindex 5 already in the list
VLAN: RTM_NEWLINK: ifi_index=7 ifname=mesh-2 ifi_family=7 ifi_flags=0x11043 ([UP][RUNNING][LOWER_UP])
VLAN: vlan_newlink(mesh-2)
_______________________________________________
Hostap mailing list
Hostap@xxxxxxxxxxxxxxxxxxx
http://lists.infradead.org/mailman/listinfo/hostap
