From: Avraham Stern <avraham.stern@xxxxxxxxx>
Add the following parameters to scan request:
1. Dwell time on each channel.
2. Whether the specified dwell time is mandatory.
In addition, add to scan results info the time that the scan actually
started, and to each scan result the time the beacon/probe was
received, both in terms of TSF of the BSS that the interface that
requested the scan is connected to (if available).
Add flags to indicate whether the driver supports dwell time
configuration and scan information reporting.
This scan configuration and information is required to support
beacon report radio measurement.
Signed-off-by: Avraham Stern <avraham.stern@xxxxxxxxx>
---
src/drivers/driver.h | 35 +++++++++++++++++++++++++++++++++++
1 file changed, 35 insertions(+)
diff --git a/src/drivers/driver.h b/src/drivers/driver.h
index 212f16c..b1c7b90 100644
--- a/src/drivers/driver.h
+++ b/src/drivers/driver.h
@@ -236,6 +236,9 @@ struct hostapd_hw_modes {
* @est_throughput: Estimated throughput in kbps (this is calculated during
* scan result processing if left zero by the driver wrapper)
* @snr: Signal-to-noise ratio in dB (calculated during scan result processing)
+ * @parent_tsf: Time when the beacon/probe was received in terms of TSF of the
+ * BSS specified by %tsf_bssid.
+ * @tsf_bssid: The BSS that %parent_tsf TSF time refers to.
* @ie_len: length of the following IE field in octets
* @beacon_ie_len: length of the following Beacon IE field in octets
*
@@ -266,6 +269,8 @@ struct wpa_scan_res {
unsigned int age;
unsigned int est_throughput;
int snr;
+ u64 parent_tsf;
+ u8 tsf_bssid[ETH_ALEN];
size_t ie_len;
size_t beacon_ie_len;
/* Followed by ie_len + beacon_ie_len octets of IE data */
@@ -472,6 +477,24 @@ struct wpa_driver_scan_params {
*/
u64 scan_cookie;
+ /**
+ * duration - Dwell time on each channel
+ *
+ * This optional parameter can be used to set the dwell time on each
+ * channel. In TUs.
+ */
+ u16 duration;
+
+ /**
+ * duration_mandatory - Whether the specified duration is mandatory
+ *
+ * If this is set, the duration specified by the %duration field is
+ * mandatory (and the driver should reject the scan request if it is
+ * unable to comply with the specified duration), otherwise it is the
+ * maximum duration and the actual duration may be shorter.
+ */
+ unsigned int duration_mandatory:1;
+
/*
* NOTE: Whenever adding new parameters here, please make sure
* wpa_scan_clone_params() and wpa_scan_free_params() get updated with
@@ -1470,6 +1493,11 @@ struct wpa_driver_capa {
*/
#define WPA_DRIVER_FLAGS_SUPPORT_RRM 0x00000010
+/** Driver supports setting the scan dwell time */
+#define WPA_DRIVER_FLAGS_SUPPORT_SET_SCAN_DWELL 0x00000020
+/** Driver supports Beacon Report Measurement */
+#define WPA_DRIVER_FLAGS_SUPPORT_BEACON_REPORT 0x00000040
+
u32 rrm_flags;
/* Driver concurrency capabilities */
@@ -4684,6 +4712,11 @@ union wpa_event_data {
* @external_scan: Whether the scan info is for an external scan
* @nl_scan_event: 1 if the source of this scan event is a normal scan,
* 0 if the source of the scan event is a vendor scan
+ * @scan_start_tsf: Time when the scan started in terms of TSF of the
+ * BSS that the interface that requested the scan is connected to
+ * (if available).
+ * @scan_start_tsf_bssid: The BSSID according to which %scan_start_tsf
+ * is set.
*/
struct scan_info {
int aborted;
@@ -4693,6 +4726,8 @@ union wpa_event_data {
size_t num_ssids;
int external_scan;
int nl_scan_event;
+ u64 scan_start_tsf;
+ u8 scan_start_tsf_bssid[ETH_ALEN];
} scan_info;
/**
--
1.9.1
_______________________________________________
Hostap mailing list
Hostap@xxxxxxxxxxxxxxxxxxx
http://lists.infradead.org/mailman/listinfo/hostap
