[PATCH v2 31/33] FT OVER_DS with fullstate station driver

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



This adds a station to the driver when doing FT OVER-DS.

Signed-off-by: Michael Braun <michael-dev@xxxxxxxxxxxxx>
---
 src/ap/sta_info.c      |  8 +++++++-
 src/ap/wpa_auth_glue.c | 35 +++++++++++++++++++++++++++++++++++
 2 files changed, 42 insertions(+), 1 deletion(-)

diff --git a/src/ap/sta_info.c b/src/ap/sta_info.c
index 20f4021..66b36c0 100644
--- a/src/ap/sta_info.c
+++ b/src/ap/sta_info.c
@@ -1007,7 +1007,13 @@ skip_counting:
 	if (wpa_auth_sta_set_vlan(sta->wpa_sm, sta->vlan_id) < 0)
 		wpa_printf(MSG_INFO, "Failed to update VLAN-ID for WPA");
 
-	if (sta->flags & (WLAN_STA_AUTH | WLAN_STA_ASSOC)) {
+	/* if station is auth or assoc OR
+	 * if station is FT_OVER_DS preauth and FULL_AP_CLIENT_STATE supported
+	 * -> bind vlan
+	 */
+	if ((sta->flags & (WLAN_STA_AUTH | WLAN_STA_ASSOC)) ||
+	    ((sta->flags & WLAN_STA_PREAUTH_FT_OVER_DS) &&
+	     FULL_AP_CLIENT_STATE_SUPP(hapd->iface->drv_flags))) {
 		ret = hostapd_drv_set_sta_vlan(iface, hapd, sta->addr,
 					       sta->vlan_id);
 		if (ret < 0)
diff --git a/src/ap/wpa_auth_glue.c b/src/ap/wpa_auth_glue.c
index 2d9fd94..bd5f627 100644
--- a/src/ap/wpa_auth_glue.c
+++ b/src/ap/wpa_auth_glue.c
@@ -643,6 +643,41 @@ hostapd_wpa_auth_add_sta_auth(void *ctx, const u8 *sta_addr,
 
 	ieee802_1x_notify_pre_auth(sta->eapol_sm, 0);
 
+	/*
+	 * If the driver supports full AP client state, add a station to the
+	 * driver before sending authentication reply to make sure the driver
+	 * has resources, and not to go through the entire authentication and
+	 * association handshake, and fail it at the end.
+	 *
+	 * Additionally, this enables OVER_DS to configure station vlan early.
+	 */
+	if (FULL_AP_CLIENT_STATE_SUPP(hapd->iface->drv_flags) &&
+	    !(sta->added_unassoc)) {
+		/*
+		 * If a station that is already associated to the AP, is trying
+		 * to authenticate again, remove the STA entry, in order to make
+		 * sure the STA PS state gets cleared and configuration gets
+		 * updated. To handle this, station's added_unassoc flag is
+		 * cleared once the station has completed association.
+		 */
+		hostapd_drv_sta_remove(hapd, sta->addr);
+		sta->flags &= ~(WLAN_STA_ASSOC | WLAN_STA_AUTH |
+				WLAN_STA_AUTHORIZED |
+				WLAN_STA_PREAUTH_FT_OVER_DS);
+
+		if (hostapd_sta_add(hapd, sta->addr, 0, 0, NULL, 0, 0,
+				    NULL, NULL, sta->flags, 0, 0, 0, 0)) {
+			hostapd_logger(hapd, sta->addr,
+				       HOSTAPD_MODULE_IEEE80211,
+				       HOSTAPD_LEVEL_NOTICE,
+				       "Could not add STA to kernel driver");
+			res = WLAN_STATUS_AP_UNABLE_TO_HANDLE_NEW_STA;
+			goto fail;
+		}
+
+		sta->added_unassoc = 1;
+	}
+
 	return 0;
 fail:
 	hostapd_allowed_address_free(&info);
-- 
2.1.4


_______________________________________________
Hostap mailing list
Hostap@xxxxxxxxxxxxxxxxxxx
http://lists.infradead.org/mailman/listinfo/hostap



[Index of Archives]     [Linux Wireless]     [Linux Kernel]     [ATH6KL]     [Linux Bluetooth]     [Linux Netdev]     [Kernel Newbies]     [IDE]     [Security]     [Git]     [Netfilter]     [Bugtraq]     [Yosemite News]     [MIPS Linux]     [ARM Linux]     [Linux Security]     [Linux RAID]     [Linux ATA RAID]     [Samba]     [Device Mapper]

  Powered by Linux