On 18/03/24 01:07, Ayush Singh wrote:
DONOTMERGE
Why?
mikroBUS addon boards allow using same mikroBUS connector for a wide range of peripherals. It is also possible for the addon board not to use all the pins in mikroBUS socket (marked by NC or Not Connected). This would require the need to create an almost new overlays for each permutation of the hardware. To overcome this, a manifest format based on Greybus manifest specification was created which allows describing mikroBUS addon boards. The reason for choosing greybus manifest for the identifier is that so far we discussed only about physical mikroBUS ports on the board, but we can
you will need to reword the commit message properly in imperative mood, here and in multiple other places.
also have mikroBUS ports on a remote microcontroller appearing on host
over greybus and there a device tree overlay solution does not work as the
standard identifier mechanism.
The patch introduces 3 new greybus descriptor types:
1. mikrobus-descriptor:
Is a fixed-length descriptor (12 bytes), and the manifest shall have
precisely one mikroBUS descriptor. Each byte describes a configuration
of the corresponding pin on the mikroBUS addon board in a clockwise
direction starting from the PWM pin omitting power (VCC and ground)
pins as same as the default state of the pin.
There are mikroBUS addon boards that use some dedicated SPI, UART, PWM,
and I2C pins as GPIO pins, so it is necessary to redefine the default
pin configuration of that pins on the host system. Also, sometimes it is
required the pull-up on the host pin for correct functionality
2. property-descriptor:
Are used to pass named properties or named GPIOs to the host. The host
system uses this information to properly configure specific board
drivers by passing the properties and GPIO name. There can be multiple
instances of property descriptors per add-on board manifest.
3. device-descriptor:
Describes a device on the mikroBUS port. The device descriptor is a
fixed-length descriptor, and there can be multiple instances of device
descriptors in an add-on board manifest in cases where the add-on board
presents more than one device to the host.
New mikroBUS addon boards also sometimes contain a 1-wire EEPROM with
the mikroBUS manifest, thus enabling plug and play support.
new mikroBUS sometimes contain an EEPROM? aren't these called Click ID compliant add-on boards? there should be clarity in the commit message.
I have also created PR to add mikrobus descriptors in Greybus spec and I think the old PR on manifesto by Vaishnav should also work. However, both of these repositories seem to be inactive. I am guessing the greybus mailing list can provide more information on how I should go about these.
Why is information like these inside the commit message, these go below the tear line.
Here is a sample mikroBUS manifest: ``` ;; ; PRESSURE CLICK ; https://www.mikroe.com/pressure-click ; CONFIG_IIO_ST_PRESS ; ; Copyright 2020 BeagleBoard.org Foundation ; Copyright 2020 Texas Instruments ; [manifest-header] version-major = 0 version-minor = 1 [interface-descriptor] vendor-string-id = 1 product-string-id = 2 [string-descriptor 1] string = MIKROE [string-descriptor 2] string = Pressure [mikrobus-descriptor] pwm-state = 4 int-state = 1 rx-state = 7 tx-state = 7 scl-state = 6 sda-state = 6 mosi-state = 5 miso-state = 5 sck-state = 5 cs-state = 5 rst-state = 2 an-state = 1 [device-descriptor 1] driver-string-id = 3 protocol = 0x3 reg = 0x5d [string-descriptor 3] string = lps331ap ``` Link: https://www.mikroe.com/clickid ClickID Link: https://docs.beagleboard.org/latest/projects/beagleconnect/index.html beagleconnect Link: https://github.com/projectara/greybus-spec Greybus Spec Link: https://github.com/projectara/greybus-spec/pull/4 Greybus Spec PR Link: https://github.com/projectara/manifesto/pull/2 manifesto PR
The manifesto PR might not be updated. Thanks and Regards, Vaishnav
Co-developed-by: Vaishnav M A <vaishnav@xxxxxxxxxxxxxxx> Signed-off-by: Vaishnav M A <vaishnav@xxxxxxxxxxxxxxx> Signed-off-by: Ayush Singh <ayushdevel1325@xxxxxxxxx> --- include/linux/greybus/greybus_manifest.h | 49 ++++++++++++++++++++++++ 1 file changed, 49 insertions(+) diff --git a/include/linux/greybus/greybus_manifest.h b/include/linux/greybus/greybus_manifest.h index bef9eb2093e9..83241e19d9b3 100644 --- a/include/linux/greybus/greybus_manifest.h +++ b/include/linux/greybus/greybus_manifest.h @@ -23,6 +23,9 @@ enum greybus_descriptor_type { GREYBUS_TYPE_STRING = 0x02, GREYBUS_TYPE_BUNDLE = 0x03, GREYBUS_TYPE_CPORT = 0x04, + GREYBUS_TYPE_MIKROBUS = 0x05, + GREYBUS_TYPE_PROPERTY = 0x06, + GREYBUS_TYPE_DEVICE = 0x07, };enum greybus_protocol {@@ -151,6 +154,49 @@ struct greybus_descriptor_cport { __u8 protocol_id; /* enum greybus_protocol */ } __packed;+/*+ * A mikrobus descriptor is used to describe the details + * about the bus ocnfiguration for the add-on board + * connected to the mikrobus port. + */ +struct greybus_descriptor_mikrobus { + __u8 pin_state[12]; +} __packed; + +/* + * A property descriptor is used to pass named properties + * to device drivers through the unified device properties + * interface under linux/property.h + */ +struct greybus_descriptor_property { + __u8 length; + __u8 id; + __u8 propname_stringid; + __u8 type; + __u8 value[]; +} __packed; + +/* + * A device descriptor is used to describe the + * details required by a add-on board device + * driver. + */ +struct greybus_descriptor_device { + __u8 id; + __u8 driver_stringid; + __u8 protocol; + __u8 reg; + __le32 max_speed_hz; + __u8 irq; + __u8 irq_type; + __u8 mode; + __u8 prop_link; + __u8 gpio_link; + __u8 reg_link; + __u8 clock_link; + __u8 pad[1]; +} __packed; + struct greybus_descriptor_header { __le16 size; __u8 type; /* enum greybus_descriptor_type */ @@ -164,6 +210,9 @@ struct greybus_descriptor { struct greybus_descriptor_interface interface; struct greybus_descriptor_bundle bundle; struct greybus_descriptor_cport cport; + struct greybus_descriptor_mikrobus mikrobus; + struct greybus_descriptor_property property; + struct greybus_descriptor_device device; }; } __packed;
_______________________________________________ greybus-dev mailing list -- greybus-dev@xxxxxxxxxxxxxxxx To unsubscribe send an email to greybus-dev-leave@xxxxxxxxxxxxxxxx
|