It appears you have configuration issue which is causing a NAT issue. Your GnuGk is deployed outside your firewall you need to either deploy another GnuGk on the inside of the firewall registered to the external GnuGk or upgrade to 2.2.5. I suggest you upgrade to GnuGk 2.2.5 and deploy GnuGk on the inside of the firewall and port forward in accordance with the following ini http://openh323gk.cvs.sourceforge.net/openh323gk/openh323gk/etc/nat.ini?revision=1.4&view=markup That should work Simon At 12:20 AM 4/04/2007, you wrote: >Hi All, > >I am currently experimenting with Gnugk 2.2.4. it is running on a Dell >Edge 850 Server, with dual Intel P4's and 1GB of RAM with Fedora Core >5. The endpoint I am using is a Polycom VSX 7000. >The firewall I have is setup so that any device inside the firewall can >go out, but only traffic coming from GNUGK can get in. The GK is acting >in both Proxy and Routed mode. The following is the core config: > ><BEGIN CONFIG> >(lines ommitted) >; >; >[GkStatus::Auth] >rule=allow > >;; >;; getting ahead of ourselves >;; >[RoutedMode] >; enable gatekeeper signaling routed mode, route H.245 channel only if >neccessary (for NATed endpoints) >GKRouted=1 >H245Routed=1 >; you may want to change it to the H.323 default 1720 >CallSignalPort=1721 >AcceptNeighborCalls=1 >AcceptUnregisteredCalls=1 >RemoveH245AddressOnTunneling=1 >RemoveCallOnDRQ=0 >DropCallsByReleaseComplete=1 >SendReleaseCompleteOnDRQ=0 >SupportNATedEndpoints=1 >TreatUnregisteredNAT=1 >TranslateFacility=1 >CallSignalHandlerNumber=10 >RtpHandlerNumber=2 >Q931PortRange=30000-39999 >H245PortRange=40000-49999 > >; proxy calls only for NATed endpoints >[Proxy] >Enable=1 >; if port forwarding is correctly configured for each endpoint, you can >disable ProxyForNAT >ProxyForNAT=1 >ProxyForSameNAT=1 >InternalNetwork=xxx.xxx.xxx.xxx/27 >T120Portrange=50000-59999 >RTPPortRange=50000-59999 ><END-CONFIG> > >So here is the problem: >I cant quite figure out what is causing the "socket has not >destination..." error. Also, when testing with others my stream going >from my video to whomever is fine, but all video comming back is choppy, >and blocky. I want it setup so that the GK handles all the video >traffic, there is no direct connection from the endpoint to endpoint, or >endpoint to MCU. > > > > > > Outside FW > Inside FW > > MCU---------|----------- Firewall >-------------------Endpoint > > | (GNUGK) > | | > > \/ > \/ \/ > >2007/04/02 14:48:05.163 3 ProxyChannel.cxx(3592) RTP >xxx.xxx.xxx.xxx:56072<=>xxx.xxx.xxx.xxx:50012<=>xxx.xxx.xxx.xxx:49158 >socket has no destination address yet, flush ignored >2007/04/02 14:48:05.183 3 ProxyChannel.cxx(3592) RTP >xxx.xxx.xxx.xxx:56072<=>xxx.xxx.xxx.xxx:50012<=>xxx.xxx.xxx.xxx:49158 >socket has no destination address yet, flush ignored >2007/04/02 14:48:05.201 3 ProxyChannel.cxx(3592) RTP >xxx.xxx.xxx.xxx:56072<=>xxx.xxx.xxx.xxx:50012<=>xxx.xxx.xxx.xxx:49158 >socket has no destination address yet, flush ignored >2007/04/02 14:48:05.203 3 ProxyChannel.cxx(3592) RTP >xxx.xxx.xxx.xxx:56072<=>xxx.xxx.xxx.xxx:50012<=>xxx.xxx.xxx.xxx:49158 >socket has no destination address yet, flush ignored >2007/04/02 14:48:05.223 3 ProxyChannel.cxx(3592) RTP >xxx.xxx.xxx.xxx:56072<=>xxx.xxx.xxx.xxx:50012<=>xxx.xxx.xxx.xxx:49158 >socket has no destination address yet, flush ignored >2007/04/02 14:48:05.243 3 ProxyChannel.cxx(3592) RTP >xxx.xxx.xxx.xxx56072<=>xxx.xxx.xxx.xxx:50012<=>xxx.xxx.xxx.xxx:49158 >socket has no destination address yet, flush ignored >2007/04/02 14:48:05.261 3 ProxyChannel.cxx(3592) RTP >xxx.xxx.xxx.xxx:56072<=>xxx.xxx.xxx.xxx:50012<=>xxx.xxx.xxx.xxx:49158 >socket has no destination address yet, flush ignored >2007/04/02 14:48:05.263 3 ProxyChannel.cxx(3592) RTP >xxx.xxx.xxx.xxx:56072<=>xxx.xxx.xxx.xxx:50012<=>xxx.xxx.xxx.xxx:49158 >socket has no destination address yet, flush ignored > >Above is just a sample of the error. While the call is in progress, >this constantly streams until the call is dropped, or I disconnect the call. > > >I am also getting the occasional "ProxyChannel.cxx(4316) Proxy >Logical channel 2 not found" error. > >Can someone give me a hand or point me in the right direction? Thanks >in advance. > >Nicholas~ > >------------------------------------------------------------------------- >Take Surveys. Earn Cash. Influence the Future of IT >Join SourceForge.net's Techsay panel and you'll get the chance to share your >opinions on IT & business topics through brief surveys-and earn cash >http://www.techsay.com/default.php?page=join.php&p=sourceforge&CID=DEVDEV >_______________________________________________________ > >Posting: mailto:Openh323gk-users@xxxxxxxxxxxxxxxxxxxxx >Archive: http://sourceforge.net/mailarchive/forum.php?forum_id=8549 >Unsubscribe: http://lists.sourceforge.net/lists/listinfo/openh323gk-users >Homepage: http://www.gnugk.org/ ------------------------------------------------------------------------- Take Surveys. Earn Cash. Influence the Future of IT Join SourceForge.net's Techsay panel and you'll get the chance to share your opinions on IT & business topics through brief surveys-and earn cash http://www.techsay.com/default.php?page=join.php&p=sourceforge&CID=DEVDEV _______________________________________________________ Posting: mailto:Openh323gk-users@xxxxxxxxxxxxxxxxxxxxx Archive: http://sourceforge.net/mailarchive/forum.php?forum_id=8549 Unsubscribe: http://lists.sourceforge.net/lists/listinfo/openh323gk-users Homepage: http://www.gnugk.org/
