The first step should be posting to the right list openh323gk-users@xxxxxxxxxxxxxxxxxxxxx (I'm forwarding the message). The second - examining GnuGk log (at trace level 5). The third - if there arer firewalls/NAT on the way - you will likely run into problems.
----- Original Message ----- From: "pilli Jyothi" <pilli.jyothi@xxxxxxxxx>
Sent: Thursday, November 11, 2004 11:23 AM
Hi Ulises,
Haven't get any reply to my previous messages which i send u already
I have a problems to configure the gnugk in WAN hope will get solution to my problem.
I want to make a call from Endpoint A which is at one state (say in India) and also registered itself with registered with Gatekeeper running at the same place in routed mode.
and other endpoint B which is running at other states(say Other than India), has to registered with gatekeeper running at Endpoint A. this is what i want to do
Ue(A)<-----> GnuGk<------>Ue(B)
But finding probelm when Endpoint B is trying to register itself with gatekeeper.... endpoint A is registered properly
But the same thing is working fine at LAN and also through Net in local place
Can any one tell me do i need to do any settings or need to change configuration
file to establish a connection between the above endpoints with gatekeeper
configuration file of gatekeeper is as below. (routed Mode)
regards jyothi
##[Gatekeeper::Main]
Fourtytwo=42
Name = WIFI GateKeeper TimeToLive=600
TotalBandwidth = 100000
[RoutedMode]; call signalling (Q.931) routed
GKRouted=1; control channel (H.245) routed
H245Routed=1; use 1721 as the port of call signalling
CallSignalPort=1721; for dual CPUs
CallSignalHandlerNumber=2; accept calls from neighbor gatekeepers
AcceptNeighborsCalls=1; don't accept calls from unregistered endpoints
AcceptUnregisteredCalls=0;
force to stay in tunneling mode if Tunneling flag is TRUE
RemoveH245AddressOnTunneling=1;
send Release Complete to drop calls DropCallsByReleaseComplete=1;
send Release Complete on receiving DRQ
SendReleaseCompleteOnDRQ=1;
accept registration of an endpoint behind an NAT box
SupportNATedEndpoints=1;
port range for Q.931 channel
Q931PortRange=30000-39999;
port range for H.245 channel
H245PortRange=40000-49999
[Proxy] Enable=0
[GkStatus::Auth] rule=allow # EOF
On Thu, 04 Nov 2004 10:58:44 -0600, Ulises Salvador Vega Arteaga <ulises.vega@xxxxxxxxxxxxxx> wrote:Hi, i've been trying without succes. As you said it works fine with netmeeting in both directions. If you can help me to find what exactlty netmeeting does in order to establish connections, that would be a lot of help? In the same way, if you are able to findout if a cisco ubr7246 if able to block incoming calls for h.323 by product id, manufacturer or something like that? It'll be great. I think that may be my mycable company has product form Quintum (www.quintum.com ) to manage h.323 calls, what about you? I tried to fake netmeeting identity in my h.323 application i made it, but the call establishment is still without succes, have you tried that.?
does anybody on the list know what exactly netmeeting does to establish a call?
pilli Jyothi wrote:
>Hi, > > I've been running some test of H.323 over cable networks with the >following configuration > > epA(1)-----------------(2) || GK ||(3) ----------(4)|| ISP over > Cable > >This the scenario where i try to test for audio > > epA(1) is an endpoint and having Static IP. > > || X|| , doble parallel bars means firewall, X represents what is in > the >middle > > *ISP over Cable network , at (4) will get Dynamic IP when connected > to Net > >* When i try to make a call from my PC ( has Static IP) to the remote >system which is having Dynamic IPconnected through cable connection is >getting cleared > >Can u tell me how to establish connection between these two endpoints >if i want to have voice chat... > >Thanks & regards >jyothi > > > >On Wed, 20 Oct 2004 17:43:00 -0600, Ulises Salvador Vega Arteaga ><ulises.vega@xxxxxxxxxxxxxx> wrote: > > >>I ran the test with Netmeeting 3.01 at noon, and it ran well. >>Any idea how could i check why there is no audio transmission over a >>cable network while using openh323.? >> >>Thanks in advanced. >> >>Ulises Vega >> >> >> >>Ulises Salvador Vega Arteaga wrote: >> >> >> >>>Hi, >>> >>>I've been running some test of H.323 over cable networks with the >>>following configuration >>> >>> >>>epA(1)-----------------(2) || GK ||(3) ----------(4)|| ISP over Cable >>>network ||(5)--------(6)epB, epC (epB, and epC use same ip address but >>>different siganling, ras, and rtp ports) >>> >>>|_____(7)epD,epE (dial-up connection 56kbps) >>> >>> (epD, and epE use same ip address but different >>>siganling, ras, and rtp ports) >>> >>>(ep, means endpoint) >>>|| X|| , doble parallel bars means firewall, X represents what is in >>>the middle >>>*epA is on private ip at (1), >>> >>>*GK is on a firewall on a server running linux redhat, working fine as >>>a proxy (I know this becuase i've tested voice transmission from >>>dial-up connection outside of the firewall as shown in epD at (7) and >>>I can communicate very clearly with epA, bidirectionally with no >>>problem). >>> >>>*ISP over Cable network , at (4) has a fixed public IP address >>>attached to epB by MAC matching, >>> at (5) has private IP >>> adress. >>> >>>*epB at 6 has private IP address >>> >>> >>>The situation is a s follows: from epB, i can registert to the GK, >>>establish a call up (setup, connect, opening of audio channels), but >>>udp packets that carry voice cannot pass to epA,or epC, even more >>>I cannot hear myself when i call epC from epB, eventhough as i said >>>before, connectino is established (arq, acf, setup,..., until opening >>>of audio channels work fine). >>> >>>Some interesting points might be: >>>*I have disabled bandwidht management at GK, the requested bandwidht >>>by any ep is 100000 (as default value for initialbandwidth in >>>H323Endpoint). I don't think it is a bandwith problem >>>because I'm receving ACF from GK. And more, I dont get a connection >>>cleared message with rease NoBandwidthAvailable, even more, audio >>>channels don't get broken because i can stay on the call hearing >>>nothing for as long as i want. >>>*The same operation was done on dialup connection (epD,epE) and works >>>fine. >>> >>>Question: >>>*what should i do to hear myself at least locally (my PC, between >>>epB, and epC) behind cable network LAN? >>>*what effect might cause a cablemodem on the PC strong enough to not >>>allow hearing myself on the same PC? >>>*in general, any idea? links that i could rview >>>*I'm about to run Netmeeting over the cable network to the ouside >>>world to see if ti works, has somebody tried this at home? >>> >>> >>>Best regards. >>> >>> >>>Ulises Vega
------------------------------------------------------- This SF.Net email is sponsored by: Sybase ASE Linux Express Edition - download now for FREE LinuxWorld Reader's Choice Award Winner for best database on Linux. http://ads.osdn.com/?ad_id=5588&alloc_id=12065&op=click
_______________________________________________________
List: Openh323gk-users@xxxxxxxxxxxxxxxxxxxxx Archive: http://sourceforge.net/mailarchive/forum.php?forum_id=8549 Homepage: http://www.gnugk.org/
