On 06/17/2015 10:57 PM, Alessandro De Salvo wrote: > Hi, > when disabling exports from gluster 3.7.1, by using gluster vol set <volume> ganesha.enable off, I always get the following error: > > Error: Dynamic export addition/deletion failed. Please see log file for details > > This message is produced by the failure of /usr/libexec/ganesha/dbus-send.sh, and in fact if I manually perform the command to remove the share I see: you got it wrong. '/usr/libexec/ganesha/dbus-send.sh' is used by Gluster-CLI to unexport the volume "gluster volume set <volname> ganesha.enable off" which rightly deletes the export file too while un-exporting the volume. > > # dbus-send --print-reply --system --dest=org.ganesha.nfsd /org/ganesha/nfsd/ExportMgr org.ganesha.nfsd.exportmgr.RemoveExport uint16:2 > Error org.freedesktop.DBus.Error.NoReply: Message did not receive a reply (timeout by message bus) > > So, there is a timeout and it fails completely. Check if nfs-ganesha is still running. There was a bug in unexporting the volume. Its been fixed recently in V2.3-dev, yet to be back-ported to V2.2-stable branch. https://review.gerrithub.io/#/c/236129/ Thanks, Soumya > In this case I think there is a bug in /usr/libexec/ganesha/dbus-send.sh, since it blindly deletes the share config if the RemoveExport fails (function check_cmd_status()), but leaves the %include inside ganesha.conf as in the check_cmd_status() there is a runaway condition and the other removal statements are then not executed. I believe the logic should be fixed here, otherwise even a restart of the service will fail due to the bad configuration. Yes. I see that the "sed -i /$VOL.conf/d $CONF" is placed after the check_cmd_status. I shall send a fix upstream in a related bug. But dynamic export removal will fail in three cases, 1. nfs-ganesha is not running. 2. The export file that is particular to that volume is somehow deleted before you perform the removal. It does depend on that file to get the export ID. 3. The bug that Soumya pointed out. If it is failing consistently, there could be something that you are missing. If you can send the exact sequence of sequence of steps that you have executed, I can help you with it. Ideally after exporting a particular volume, you'll see an entry in the /etc/ganesha/ganesha.conf file and the export file in "/etc/ganesha/exports" dir. If you have this in place and nfs-ganesha running, then dynamic export removal should work just fine. Meghana > > What’s more worrying is the problem with the dbus. Issuing a DisplayExport before the RemoveExport apparently fixes the problem, so something like this always works: > > # dbus-send --print-reply --system --dest=org.ganesha.nfsd /org/ganesha/nfsd/ExportMgr org.ganesha.nfsd.exportmgr.DisplayExport uint16:2 > # dbus-send --print-reply --system --dest=org.ganesha.nfsd /org/ganesha/nfsd/ExportMgr org.ganesha.nfsd.exportmgr.RemoveExport uint16:2 > > So, it’s like the DisplayExport is forcing someway a refresh that is needed by the RemoveExport. Any idea why? > I’m using the latest version of ganesha 2.2.0, i.e. 2.2.0-3. > Thanks, > > Alessandro > > PS: sorry for reporting so many things in a few days :-) > > > > ------------------------------------------------------------------------------ > > > > _______________________________________________ > Nfs-ganesha-devel mailing list > Nfs-ganesha-devel@xxxxxxxxxxxxxxxxxxxxx > https://lists.sourceforge.net/lists/listinfo/nfs-ganesha-devel > ------------------------------------------------------------------------------ _______________________________________________ Nfs-ganesha-devel mailing list Nfs-ganesha-devel@xxxxxxxxxxxxxxxxxxxxx https://lists.sourceforge.net/lists/listinfo/nfs-ganesha-devel _______________________________________________ Gluster-users mailing list Gluster-users@xxxxxxxxxxx http://www.gluster.org/mailman/listinfo/gluster-users
