Hi willem,
Please find the inlined comments:
----- Original Message -----
> From: "Willem" <gwillem at gmail.com>
> To: gluster-users at gluster.org
> Sent: Thursday, April 18, 2013 11:58:46 PM
> Subject: Low (<0.2ms) latency reads, is it possible at all?
>
> I'm testing GlusterFS viability for use with a typical PHP webapp (ie. lots
> of small files). I don't care so much for the C in the CAP theorem, as I
> have very few writes. I could live with a write propagation delay of 5
> minutes (or dirty caches for up to 5 minutes).
>
> So I'm optimizing for low latency reads of small files. My testsetup is 2
> node replication. Each node is both server and gluster client. Both are in
> sync. I stop glusterfs-server @ node2. @node1, I run a simple benchmark:
> repeatedly (to prime the cache) open & close 1000 small files. I have
> enabled the client-side io-cache and quick-read translators (see below for
> config).
>
> The results are consistently 2 ms per open (O_RDONLY) call. Which is too
> slow, unfortunately, as I need < 0.2ms.
>
> The same test with a local Gluster server and NFS mount, I get somewhat
> better performance but still 0.6ms.
>
> The same test with Linux NFS server (v3) and local mount, I get 0.12ms per
> open.
>
> I can't explain the lag using Gluster, because I can't see any traffic being
> sent to node2. I would expect that using the io-cache translator and
> local-only operation, the performance would approach that of the kernel FS
> cache.
>
> Is this assumption correct? If yes, how would I profile the client sub system
> to detect the bottleneck?
>
> If no, then I have to accept that 0.8ms open calls are the best that I could
> squeeze out of this system. Then I'll probably look into AFS, userspace
> async replication or gluster NFS mount with cachefilesd. Which would you
> recommend?
>
> Thanks a lot!
> BTW I like Gluster a lot, and hope that it is also suitable for this small
> files use case ;)
>
> //Willem
>
> PS Am testing with kernel 3.5.0-17-generic 64bit and gluster 3.2.5-1ubuntu1.
>
> Client volfile:
> +------------------------------------------------------------------------------+
> 1: volume testvol-client-0
> 2: type protocol/client
> 3: option remote-host g1
> 4: option remote-subvolume /data
> 5: option transport-type tcp
> 6: end-volume
> 7:
> 8: volume testvol-client-1
> 9: type protocol/client
> 10: option remote-host g2
> 11: option remote-subvolume /data
> 12: option transport-type tcp
> 13: end-volume
> 14:
> 15: volume testvol-replicate-0
> 16: type cluster/replicate
> 17: subvolumes testvol-client-0 testvol-client-1
> 18: end-volume
> 19:
> 20: volume testvol-write-behind
> 21: type performance/write-behind
> 22: option flush-behind on
> 23: subvolumes testvol-replicate-0
> 24: end-volume
> 25:
> 26: volume testvol-io-cache
> 27: type performance/io-cache
> 28: option max-file-size 256KB
> 29: option cache-timeout 60
> 30: option priority *.php:3,*:0
> 31: option cache-size 256MB
> 32: subvolumes testvol-write-behind
> 33: end-volume
> 34:
> 35: volume testvol-quick-read
> 36: type performance/quick-read
default value for option "max-file-size" is 64KB. Seems like your files are bigger than 64KB. Can you add this option and rerun the tests? Also can you rerun the tests by disabling quick-read and compare the results?
> 37: option cache-size 256MB
> 38: subvolumes testvol-io-cache
> 39: end-volume
> 40:
> 41: volume testvol
> 42: type debug/io-stats
> 43: option latency-measurement off
> 44: option count-fop-hits off
> 45: subvolumes testvol-quick-read
> 46: end-volume
>
> Server volfile:
> +------------------------------------------------------------------------------+
> 1: volume testvol-posix
> 2: type storage/posix
> 3: option directory /data
> 4: end-volume
> 5:
> 6: volume testvol-access-control
> 7: type features/access-control
> 8: subvolumes testvol-posix
> 9: end-volume
> 10:
> 11: volume testvol-locks
> 12: type features/locks
> 13: subvolumes testvol-access-control
> 14: end-volume
> 15:
> 16: volume testvol-io-threads
> 17: type performance/io-threads
> 18: subvolumes testvol-locks
> 19: end-volume
> 20:
> 21: volume testvol-marker
> 22: type features/marker
> 23: option volume-uuid bc89684f-569c-48b0-bc67-09bfd30ba253
> 24: option timestamp-file /etc/glusterd/vols/testvol/marker.tstamp
> 25: option xtime off
> 26: option quota off
> 27: subvolumes testvol-io-threads
> 28: end-volume
> 29:
> 30: volume /data
> 31: type debug/io-stats
> 32: option latency-measurement off
> 33: option count-fop-hits off
> 34: subvolumes testvol-marker
> 35: end-volume
> 36:
> 37: volume testvol-server
> 38: type protocol/server
> 39: option transport-type tcp
> 40: option auth.addr./data.allow *
> 41: subvolumes /data
> 42: end-volume
>
> My benchmark to simulate PHP webapp i/o:
> #!/usr/bin/env python
>
> import sys
> import os
> import time
> import optparse
>
> def print_timing(func):
> def wrapper(*arg):
> t1 = time.time()
> res = func(*arg)
> t2 = time.time()
> print '%-15.15s %6d ms' % (func.func_name, int ( (t2-t1)*1000.0 ))
> return res
> return wrapper
>
>
> def parse_options():
> parser = optparse.OptionParser()
> parser.add_option("--path", '-p', default="/mnt/glusterfs",
> help="Base directory for running tests (default: /mnt/glusterfs)",
> )
> parser.add_option("--num", '-n', type="int", default=100,
> help="Number of files per test (default: 100)",
> )
> (options, args) = parser.parse_args()
> return options
>
> class FSBench():
> def __init__(self,path="/tmp",num=100):
> self.path = path
> self.num = num
> @print_timing
> def test_open_read(self):
> for filename in self.get_files():
> f = open(filename)
> data = f.read()
> f.close()
> def get_files(self):
> for i in range(self.num):
> filename = self.path + "/test_%03d" % i
> yield filename
> @print_timing
> def test_stat(self):
> for filename in self.get_files():
> os.stat(filename)
>
> @print_timing
> def test_stat_nonexist(self):
> for filename in self.get_files():
> try:
> os.stat(filename+"blkdsflskdf")
> except OSError:
> pass
> @print_timing
> def test_write(self):
> for filename in self.get_files():
> f = open(filename,'w')
> f.write('hi there\n')
> f.close()
> @print_timing
> def test_delete(self):
> for filename in self.get_files():
> os.unlink(filename)
> if __name__ == '__main__':
>
> options = parse_options()
> bench = FSBench(path=options.path, num=options.num)
> bench.test_write()
> bench.test_open_read()
> bench.test_stat()
> bench.test_stat_nonexist()
> bench.test_delete()
>
>
>
>
> _______________________________________________
> Gluster-users mailing list
> Gluster-users at gluster.org
> http://supercolony.gluster.org/mailman/listinfo/gluster-users
