What are the advantages of XFS over ext3 (which I'm currently using)? My fear with XFS when selecting a filesystem was that it's not as active or as well supported as ext3 and if things go wrong, how easy would it be to recover? I have 6 x 1TB disks in a hardware raid 6 with battery backup and UPS, it's now just the performance I need to get sorted... ________________________________ From: Liam Slusser [mailto:lslusser at gmail.com] Sent: 12 August 2009 20:35 To: Mark Mielke Cc: Hiren Joshi; gluster-users at gluster.org Subject: Re: Performance I had a similar situation. My larger gluster cluster has two nodes but each node has 72 1.5tb hard drives. I ended up creating three 30TB 24 drive raid6 arrays, formated with xfs and 64bit-inodes, and then exporting three bricks with gluster. I would recommend using a hardware raid controller with battery backup power, UPS power, and a journaled filesystem and i think you'll be fine. I'm exporting the three bricks on each of my two nodes, the clients are using replication to replicate each of the three bricks on each server and then using distribute to tie it all together. liam On Wed, Aug 12, 2009 at 10:51 AM, Mark Mielke <mark at mark.mielke.cc> wrote: On 08/12/2009 01:24 PM, Hiren Joshi wrote: 36 partitions on each server - the word "partition" is ambiguous. Are they 36 separate drives? Or multiple partitions on the same drive. If multiple partitions on the same drive, this would be a bad idea, as it would require the disk head to move back and forth between the partitions, significantly increasing the latency, and therefore significantly reducing the performance. If each partition is on its own drive, you still won't see benefit unless you have many clients concurrently changing many different files. In your above case, it's touching a single file in sequence, and having a cluster is costing you rather than benefitting you. We went with 36 partitions (on a single raid 6 drive) incase we got file system corruption, it would take less time to fsck a 100G partition than a 3.6TB one. Would a 3.6TB single disk be better? Putting 3.6 TB on a single disk sounds like a lot of eggs in one basket. :-) If you are worried about fsck, I would definitely do as the other poster suggested and use a journalled file system. This nearly eliminates the fsck time for most situations. This would be whether using 100G partitions or using 3.6T partitions. In fact, there is very few reasons not to use a journalled file system these days. As for how to deal with data on this partition - the file system is going to have a better chance of placing files close to each other, than setting up 36 partitions and having Gluster scatter the files across all of them based on a hash. Personally, I would choose 4 x 1 Tbyte drives over 1 x 3.6 Tbyte drive, as this nearly quadruples my bandwidth and for highly concurrent loads, nearly divides by four the average latency to access files. But, if you already have the 3.6 Tbyte drive, I think the only performance-friendly use would be to partition it based upon access requirements, rather than a hash (random). That is, files that are accessed frequently should be clustered together at the front of a disk, files accessed less frequently could be in the middle, and files accessed infrequently could be at the end. This would be a three partition disk. Gluster does not have a file system that does this automatically (that I can tell), so it would probably require a software solution on your end. For example, I believe dovecot (IMAP server) allows an "alternative storage" location to be defined, so that infrequently read files can be moved to another disk, and it knows to check the primary storage first, and fall back to the alternative storage after. It you can't break up your storage by access patterns, then I think a 3.6 Tbyte file system might still be the next best option - it's still better than 36 partitions. But, make sure you have a good file system on it, that scales well to this size. Cheers, mark -- Mark Mielke<mark at mielke.cc> _______________________________________________ Gluster-users mailing list Gluster-users at gluster.org http://gluster.org/cgi-bin/mailman/listinfo/gluster-users
