Re: ping timeout

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



On Thu, 25 Mar 2010 09:56:24 +0000
Gordan Bobic <gordan@xxxxxxxxxx> wrote:

> > If I have your mentioned scenario right, including what you believe 
> > should happen:
> > 
> >     * First node goes down. Simple enough.
> >     * Second node has new file operations performed on it that the first
> >       node does not get.
> >     * First node comes up. It is completely fenced from all other
> >       machines to get itself in sync with the second node.
> >     * Second node goes down. Is it before/after first node is synced?
> >           o If it is before then you have a fully isolated FS that is
> >             not accessible.
> >           o If it is after then you don't have a problem.
> > 
> > I would suggest writing a script and performing some firewalling to 
> > perform the fencing.
> 
> This is not really good enough - you need an out-of-band fencing device 
> that you can use to forcibly down the node that disconnected, e.g. 
> remote power-off by power management (e.g. UPS or a network controllable 
> power bar) or remote server management (Dell DRAC, Raritan eRIC G4, HP 
> iLO, Sun LOM, etc.). When the node gets rebooted, it has to notice there 
> are other nodes already up and specifically set itself into such a mode 
> that it will lose any contest on being the source node for resync until 
> it has fully checked all the files' metadata against it's peers.
> 
> > I believe you can run ls -R on the file-system to 
> > get it in sync. You would need to mount glfs locally on the first node, 
> > get it in sync, then open the firewall ports afterward. Is that an 
> > appropriate solution?
> 
> The problem is that firewalling would have to be applied by every node 
> other than the node that dropped off, and this would need to be 
> communicated to all the other nodes, and they would have to confirm 
> before the fencing action is deemed to have succeeded. This is a lot 
> more complex and error prone compared to just using a single point of 
> fencing for each node such as a network controlled power bar.
> (e.g. 
> http://www.linuxfordevices.com/c/a/News/Entrylevel-4port-IP-power-switch-runs-Linux/
> )

Let me add some thoughts here:
First it looks obvious to me that fencing is not needed for glusterfs in the
described cases. If your first node comes up again it will not deliver data
that is not in-sync with the second node, that is what glusterfs is all about.
Now, when your second nodes goes down while the first is not completely synced
you only have these choices:
1. Blow up the setup and deliver nothing
2. Deliver what the first node actually has.
It looks obvious that the second choice is preferred because whatever the
out-of-sync data is, there is likely in-sync data too to be served. And so you
are at least partly saved.

The real hot topic here is how the time between the first node coming back and
the second node going down is used for an optimal self heal procedure. The
risk of split brain is lower the faster the self heal procedure works.
It is obvious that the optimal strategy has to know exactly what files to
heal. And I just made a proposal for that in another post.
Doing ls -lR will be no good strategy for simple runtime reasons if you have
large amounts of data.
 
> Gordan

-- 
Regards,
Stephan





[Index of Archives]     [Gluster Users]     [Ceph Users]     [Linux ARM Kernel]     [Linux ARM]     [Linux Omap]     [Fedora ARM]     [IETF Annouce]     [Security]     [Bugtraq]     [Linux]     [Linux OMAP]     [Linux MIPS]     [eCos]     [Asterisk Internet PBX]     [Linux API]

  Powered by Linux