Hi, According to my last mail. Is there any way to figure out the issue? Thanks & regards mappy On 10/28/14, Manpreet Singh <mappysingh@xxxxxxxxx> wrote: > Hi, > You are right its 32-bit assembler. I tried these 2 ways to configure > > Way 1 > My configuration:- > In my pc latest version of gcc-4.8 is install and i want to configure > and run gcc testsuite for gcc-4.4.5 > Ubuntu 14.04 > Host = x86_64-linux-gnu > Build = x86_64-linux-gnu > Target = powerpc-linux-gnu > > These are the steps which i performed to run testsuite > I am trying to run configure with this script > > a) sourcedir.../gcc-4.4.5/configure --prefix=/tmp/gcc-4.4.5 > --enable-languages=c,c++ --build=x86_64-pc-linux-gnu > --host=x86_64-pc-linux-gnu --target=powerpc-linux-gnu > --enable-languages=c,c++ --enable-long-long > > > b) And then to build gcc :- > make all-gcc > > c) To run the testsuite :- builddir.../gcc-4.4.5/gcc > make check (in build dir) > > This is the failure when i configured gcc-4.4.5 with above script > Failure is > FAIL: gcc.c-torture/compile/20000105-1.c -O0 (test for excess errors) > Excess errors: > /build_dir.../gcc-4.4/new_build/gcc/as: 76: exec: : Permission denied > same failure many thousand times. > > _________________________________________________________________________________________________________________________________________________________________________________________________________ > > Way 2 > > a) I used already built assembler i.e. i already mentioned above is > 32 bit assembler > sourcedir.../gcc-4.4.5/configure --prefix=/tmp/gcc-4.4.5 > --with-as=/path/to/..../bin/ppc_oea-as > --with-ld=/path/to/..../bin/ppc_oea-ld --enable-languages=c,c++ > --disable-bootstrap --disable-libgomp --disable-libstdcxx-pch > --with-ranlib=/path/to/..../bin/ppc_oea-ranlib > > > b) And then to build gcc :- > make all-gcc > > c) To run the testsuite :- builddir.../gcc-4.4.5/gcc > make check(in build dir) > > > And this the failure when i configured with way 2 > > /tmp/cc7EMVR7.s: Assembler messages: > /tmp/cc7EMVR7.s:8: Error: Unrecognized opcode: `pushq' > /tmp/cc7EMVR7.s:10: Error: Unrecognized opcode: `movq' > /tmp/cc7EMVR7.s:13: Error: Unrecognized opcode: `subq' > same failure many thousand times. > > Thanks & regards > Manpreet Singh > > On 10/28/14, Jonathan Wakely <jwakely.gcc@xxxxxxxxx> wrote: >> On 28 October 2014 10:33, Manpreet Singh wrote: >>> Hi, >>> Thanks, now i can build it without error. But, when i run that >>> make check(testsuite) in command line. >>> Again giving lots of failure. >>> e.g >>> /tmp/cc7EMVR7.s: Assembler messages: >>> /tmp/cc7EMVR7.s:8: Error: Unrecognized opcode: `pushq' >>> /tmp/cc7EMVR7.s:10: Error: Unrecognized opcode: `movq' >>> /tmp/cc7EMVR7.s:13: Error: Unrecognized opcode: `subq' >>> same failure many thousand times. >>> How would i get rid off this failure? >> >> Your assembler doesn't understand x86_64 instructions. I would guess >> either you've got a 32-bit x86 assembler or an assembler for a totally >> different architecture. >> >> It would probably help if you said what kind of system you're running >> on and how you configured GCC, so we don't have to guess what you're >> trying to do. >> >
