I'm right with you all the way up to step 7: #7) cd objdir; ./../gcc-4.6.2/configure; [completes with no problem] #8) make; [gives me the same error messages] Any ideas about what's happening? > Date: Fri, 9 Mar 2012 14:04:54 +0000 > Subject: Re: GCJ gen-fib information. > From: dnpaterson@xxxxxxxxx > To: stargate7thsymbol@xxxxxxxxxx > CC: gcc-help@xxxxxxxxxxx > > On 9 March 2012 02:38, Me Myself and I <stargate7thsymbol@xxxxxxxxxx> wrote: > > > > I have gen-fib located inside > > > > .../objdir/gmp/ > > > > It only tells me that it wants > > > > Usage: gen-bases <header|table> <limbbits> <nailbits> > > > > make install; > > > > [I am stuck on this gcj with gcc compilation, which at the make; stage, stops with this message:] > > > > fib2_ui.c:76:29: error: 'FIB_TABLE_LIMIT' undeclared (first use in this function) > > fib2_ui.c:76:29: note: each undeclared identifier is reported only once for each function it appears in > > make[5] *** [fib2_ui.lo] Error 1 > > make[5] Leaving directory '/home/User/gcc-4.6.2/objdir/gmp/mpn' > > make[4] ***all-recursive] Error 1 > > make[4] Leaving directory '/home/User/gcc-4.6.2/objdir/gmp' > > make[3] *** [all] Error 2 > > make[3] Leaving directory '/home/User/gcc-4.6.2/objdir/gmp' > > make[2] *** [all-stage1-gmp] Error 2 > > make[2] Leaving directory '/home/User/gcc-4.6.2/objdir' > > make[1] *** [stage1-bubble] Error 2 > > make[1] Leaving directory '/home/User/gcc-4.6.2/objdir' > > make: *** [all] Error 2 > > Those error messages don't match the commands you previously said you > used. In particular there should not be an "objdir" under gcc-4.6.2, > and the build should definitely not be happening in that directory > even if it does exist... > > To try to get to the bottom of your problem I've tried to recreate it > using the following steps :- > > 1. Starting in an EMPTY directory (Test), unzip gcc-4.6.2 - this give > me Test/gcc-4.6.2. > > 2. cd gcc-4.6.2 > > 3. ./contrib/download_prerequisites - works OK with no errors > > 4. cd .. - now back in /Test directory > > 5. mkdir objdir > > 6. cd objdir - now in Test/objdir > > 7. ../gcc-4.6.2/configure - works OK with no errors > > 8. make - works OK with no errors!! :-) > > At no point does an "objdir" directory appear anywhere under gcc-4.6.2 > (although if it did momentarily I may have missed it, as I ran this > while going over lecture notes and only checked every few minutes). > However fib_table.h and gen-fib.exe were created successfully in > Test/objdir/gmp. > > I think, looking through your previous posts, you're either not > entering the commands you should be (or think you are), not running in > the correct directory, or copying error messages from previous posts > instead of the latest run on your machine. > > Step 1 above - start in an EMPTY directory - is probably the most > important, as you may have corrupted your source tree by configuring > or buiding within it. Delete everything and start from scratch again. > It won't take long, and will save a huge amount of time in the long > run. > > Please, take a step back, clean off everything you've done - it isn't > working, and may never work - and go through the process slowly and > carefully again. > > Regards, > > David P. > > PS - you don't have to start a new thread for every additional > question. It makes the discussion difficult to follow...
