On Sat, Oct 16, 2021 at 06:09:37PM +0800, Zorro Lang wrote: > On Fri, Oct 15, 2021 at 08:50:24PM -0700, Darrick J. Wong wrote: > > On Sat, Oct 16, 2021 at 10:14:56AM +0800, Zorro Lang wrote: > > > Sometimes g/648 fail to unmount dmerror with this error: > > > > > > umount: /mnt/xfstests/scratch: target is busy. > > > > > > Even worse, it will cause all later test cases fail as: > > > > > > mount: bad usage > > > Try 'mount --help' for more information. > > > check: failed to mount $SCRATCH_DEV using specified options > > > Interrupted! > > > > > > So we shouldn't _fail directly if dmerror_unmount fails, use a while > > > loop to try to make sure it's unmounted. > > > > Can we preserve the "iteration XXX scratch unmount failed" message, > > please? > > Sure, how about this: > - _dmerror_unmount || _fail "iteration $i scratch unmount failed" > + _dmerror_unmount >> $seqres.full 2>&1 > + while [ $? -ne 0 ]; do > + echo "iteration $i scratch unmount failed" >> $seqres.full > + sleep 1 > + _dmerror_unmount >> $seqres.full 2>&1 > + done > > Or this (if you don't like the infinite while loop). > > + is_unmounted=1 > + for ((j = 0; j < 50; j++)); do > + sleep 1 > + _dmerror_unmount > $tmp.unmount.err 2>&1 > + if [ $? -eq 0 ];then > + is_unmounted=0 > + break > + fi > + done > + if [ $is_unmounted -ne 0 ];then > + cat $tmp.unmount.err > + _fail "iteration $i scratch unmount failed" > + fi > > Or other suggestions you have :) I like the second one. FWIW the reason for "iteration XXX umount failed" is that reviewers asked for that diagnostic capability so that it would be easier to figure out how much progress the test made before something broke. --D > > Thanks, > Zorro > > > > > --D > > > > > Signed-off-by: Zorro Lang <zlang@xxxxxxxxxx> > > > --- > > > tests/generic/648 | 8 ++++++-- > > > 1 file changed, 6 insertions(+), 2 deletions(-) > > > > > > diff --git a/tests/generic/648 b/tests/generic/648 > > > index 83dd111d..218f207b 100755 > > > --- a/tests/generic/648 > > > +++ b/tests/generic/648 > > > @@ -104,7 +104,7 @@ for i in $(seq 1 $((25 * TIME_FACTOR)) ); do > > > wait > /dev/null 2>&1 > > > ps -e | grep fsstress > /dev/null 2>&1 > > > done > > > - for ((i = 0; i < 10; i++)); do > > > + for ((j = 0; j < 10; j++)); do > > > test -e "$snap_aliveflag" || break > > > sleep 1 > > > done > > > @@ -112,7 +112,11 @@ for i in $(seq 1 $((25 * TIME_FACTOR)) ); do > > > # Mount again to replay log after loading working table, so we have a > > > # consistent fs after test. > > > $UMOUNT_PROG $loopmnt > > > - _dmerror_unmount || _fail "iteration $i scratch unmount failed" > > > + _dmerror_unmount > /dev/null 2>&1 > > > + while [ $? -ne 0 ]; do > > > + sleep 1 > > > + _dmerror_unmount > /dev/null 2>&1 > > > + done > > > _dmerror_load_working_table > > > if ! _dmerror_mount; then > > > _metadump_dev $DMERROR_DEV $seqres.scratch.$i.md > > > -- > > > 2.31.1 > > > > > >