On 18/9/19 2:56 PM, Qu Wenruo wrote:
[BUG] When btrfs/011 is executed on a fast enough system (fully memory backed VM, with test device has unsafe cache mode), the test can fail like this: btrfs/011 43s ... [failed, exit status 1]- output mismatch (see /home/adam/xfstests-dev/results//btrfs/011.out.bad) --- tests/btrfs/011.out 2019-07-22 14:13:44.643333326 +0800 +++ /home/adam/xfstests-dev/results//btrfs/011.out.bad 2019-09-18 14:49:28.308798022 +0800 @@ -1,3 +1,4 @@ QA output created by 011 *** test btrfs replace -*** done +failed: '/usr/bin/btrfs replace cancel /mnt/scratch' +(see /home/adam/xfstests-dev/results//btrfs/011.full for details) ... [CAUSE] Looking into the full output, it shows: ... Replace from /dev/mapper/test-scratch1 to /dev/mapper/test-scratch2 # /usr/bin/btrfs replace start -f /dev/mapper/test-scratch1 /dev/mapper/test-scratch2 /mnt/scratch # /usr/bin/btrfs replace cancel /mnt/scratch INFO: ioctl(DEV_REPLACE_CANCEL)"/mnt/scratch": not started failed: '/usr/bin/btrfs replace cancel /mnt/scratch' So this means the replace is already finished before we cancel it. For fast system, it's very common. [FIX] Instead of using _run_btrfs_util_prog which requires 0 as return value, we just call "$BTRFS_UTIL_PROG replace cancel" and ignore all its stderr/stdout, and completely rely on "$BTRFS_UTIL_PROG replace status" output to verify the work. Furthermore if we finished replac before cancelling it, we should replace again to switch the device back, or after the test case, btrfs check will fail as there is no valid btrfs on that replaced device. Signed-off-by: Qu Wenruo <wqu@xxxxxxxx> --- tests/btrfs/011 | 16 ++++++++++++++-- 1 file changed, 14 insertions(+), 2 deletions(-) diff --git a/tests/btrfs/011 b/tests/btrfs/011 index 89bb4d11..858b00e8 100755 --- a/tests/btrfs/011 +++ b/tests/btrfs/011 @@ -148,13 +148,25 @@ btrfs_replace_test() # background the replace operation (no '-B' option given) _run_btrfs_util_prog replace start -f $replace_options $source_dev $target_dev $SCRATCH_MNT sleep 1 - _run_btrfs_util_prog replace cancel $SCRATCH_MNT + # 1s is enough for fast system to finish replace, so here we + # ignore all the output, completely rely on later status + # output to determine + $BTRFS_UTIL_PROG replace cancel $SCRATCH_MNT &> /dev/null# 'replace status' waits for the replace operation to finish# before the status is printed $BTRFS_UTIL_PROG replace status $SCRATCH_MNT > $tmp.tmp 2>&1 cat $tmp.tmp >> $seqres.full - grep -q canceled $tmp.tmp || _fail "btrfs replace status (canceled) failed" + grep -q -e canceled -e finished $tmp.tmp ||\ + _fail "btrfs replace status (canceled) failed" + + # If replace finished before cancel, replace them back or + # the final fsck after test case will fail as there is no btrfs + # on the $source_dev anymore + if grep -q -e finished $tmp.tmp ; then + $BTRFS_UTIL_PROG replace start -Bf $replace_options \ + $target_dev $source_dev $SCRATCH_MNT + fi else if [ "${quick}Q" = "thoroughQ" ]; then # On current hardware, the thorough test runs
Faced the same problem before. But I don't have a good solution to fix. Because the idea of the test case appears to test the replace cancel. This change makes it not to error if replace is not running in the first place. Thanks, Anand
