Add some infrastructure in common/dmdelay to support use of the dm-delay
device-mapper module within tests. This is effectively copied from the
existing infrastructure in common/dmflakey. This provides the ability to
delay I/O. It only supports delaying read I/O as that is all that is
required at this point in time.
Signed-off-by: Brian Foster <bfoster@xxxxxxxxxx>
---
common/dmdelay | 89 ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
1 file changed, 89 insertions(+)
create mode 100644 common/dmdelay
diff --git a/common/dmdelay b/common/dmdelay
new file mode 100644
index 0000000..c53e2dd
--- /dev/null
+++ b/common/dmdelay
@@ -0,0 +1,89 @@
+##/bin/bash
+#
+# Copyright (c) 2016 Red Hat, Inc. All Rights Reserved.
+#
+# This program is free software; you can redistribute it and/or
+# modify it under the terms of the GNU General Public License as
+# published by the Free Software Foundation.
+#
+# This program is distributed in the hope that it would be useful,
+# but WITHOUT ANY WARRANTY; without even the implied warranty of
+# MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+# GNU General Public License for more details.
+#
+# You should have received a copy of the GNU General Public License
+# along with this program; if not, write the Free Software Foundation,
+# Inc., 51 Franklin St, Fifth Floor, Boston, MA 02110-1301 USA
+#
+#
+# common functions for setting up and tearing down a dmdelay device
+
+DELAY_NONE=0
+DELAY_READ=1
+
+echo $MOUNT_OPTIONS | grep -q dax
+if [ $? -eq 0 ]; then
+ _notrun "Cannot run tests with DAX on dmdelay devices"
+fi
+
+_init_delay()
+{
+ local BLK_DEV_SIZE=`blockdev --getsz $SCRATCH_DEV`
+ DELAY_DEV=/dev/mapper/delay-test
+ DELAY_TABLE="0 $BLK_DEV_SIZE delay $SCRATCH_DEV 0 0"
+ DELAY_TABLE_RDELAY="0 $BLK_DEV_SIZE delay $SCRATCH_DEV 0 10000 $SCRATCH_DEV 0 0"
+ $DMSETUP_PROG create delay-test --table "$DELAY_TABLE" || \
+ _fatal "failed to create delay device"
+ $DMSETUP_PROG mknodes > /dev/null 2>&1
+}
+
+_mount_delay()
+{
+ _scratch_options mount
+ mount -t $FSTYP $SCRATCH_OPTIONS $MOUNT_OPTIONS $DELAY_DEV $SCRATCH_MNT
+}
+
+_unmount_delay()
+{
+ $UMOUNT_PROG $SCRATCH_MNT
+}
+
+_cleanup_delay()
+{
+ # If dmsetup load fails then we need to make sure to do resume here
+ # otherwise the umount will hang
+ $DMSETUP_PROG resume delay-test > /dev/null 2>&1
+ $UMOUNT_PROG $SCRATCH_MNT > /dev/null 2>&1
+ # wait for device to be fully settled so that 'dmsetup remove' doesn't
+ # fail due to EBUSY
+ $UDEV_SETTLE_PROG >/dev/null 2>&1
+ $DMSETUP_PROG remove delay-test > /dev/null 2>&1
+ $DMSETUP_PROG mknodes > /dev/null 2>&1
+}
+
+# _load_delay_table <table> [lockfs]
+#
+# This defaults to --nolockfs, which doesn't freeze_fs() before loading the new
+# table, so it simulates power failure.
+_load_delay_table()
+{
+ table="$DELAY_TABLE"
+ [ $1 -eq $DELAY_READ ] && table="$DELAY_TABLE_RDELAY"
+
+ suspend_opt="--nolockfs"
+ [ $# -gt 1 ] && [ $2 -eq 1 ] && suspend_opt=""
+
+ # run a suspend/resume cycle to avoid excessive resume delays once a
+ # delay is introduced below
+ $DMSETUP_PROG suspend $suspend_opt delay-test
+ $DMSETUP_PROG resume $suspend_opt delay-test
+
+ $DMSETUP_PROG suspend $suspend_opt delay-test
+ [ $? -ne 0 ] && _fatal "failed to suspend delay-test"
+
+ $DMSETUP_PROG load delay-test --table "$table"
+ [ $? -ne 0 ] && _fatal "failed to load table into delay-test"
+
+ $DMSETUP_PROG resume delay-test
+ [ $? -ne 0 ] && _fatal "failed to resume delay-test"
+}
--
2.5.5
--
To unsubscribe from this list: send the line "unsubscribe fstests" in
the body of a message to majordomo@xxxxxxxxxxxxxxx
More majordomo info at http://vger.kernel.org/majordomo-info.html
