Fedora 12 RC3 cannot install to SATA disk

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Machine is HP d530 convertible tower with IDE drive on the primary
IDE controller, CD ROM on the secondary IDE controller, SATA drive
on the 0th SATA controller.

I was able to install Fedora 10 on this machine - well I went as far
as choosing a custom disk arrangement and it showed the SATA disk as
sdb and I partitioned it and created file systems on it.

In Fedora 11 this was broken, the disk sdb did not show up in the
step where disk arrangement is to be chosen.  It showed only sda,
the IDE drive.  I reported this at the time.

In Fedora 12 RC3 the same situation exists.  After trying unsuccessfully
to install, with only sda being shown in the disk configuration screen,
I rebooted from CD with the rescue option so I could get a shell.

The disk is seen at that level.
/dev/sda
/dev/sda1
/dev/sdb
/dev/sdb1
/dev/sdb2
/dev/sdc
/dev/sdc1

sda is the IDE drive, sdb is the SATA drive, sdb1 and 2 are the partitions
I created with Fedora 10 install CDs.  sdc is a USB thumb drive.

lspci shows
00:00.0 Host bridge: Intel Corporation 82865G/PE/P DRAM Controller/Host-Hub Interface (rev 02)
00:02.0 VGA compatible controller: Intel Corporation 82865G Integrated Graphics Controller (rev 02)
00:06.0 System peripheral: Intel Corporation 82865G/PE/P Processor to I/O Memory Interface (rev 02)
00:1d.0 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #1 (rev 02)
00:1d.1 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #2 (rev 02)
00:1d.2 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB UHCI Controller #3 (rev 02)
00:1d.7 USB Controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) USB2 EHCI Controller (rev 02)
00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev c2)
00:1f.0 ISA bridge: Intel Corporation 82801EB/ER (ICH5/ICH5R) LPC Interface Bridge (rev 02)
00:1f.1 IDE interface: Intel Corporation 82801EB/ER (ICH5/ICH5R) IDE Controller (rev 02)
00:1f.2 IDE interface: Intel Corporation 82801EB (ICH5) SATA Controller (rev 02)
00:1f.3 SMBus: Intel Corporation 82801EB/ER (ICH5/ICH5R) SMBus Controller (rev 02)
00:1f.5 Multimedia audio controller: Intel Corporation 82801EB/ER (ICH5/ICH5R) AC'97 Audio Controller (rev 02)
05:02.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5782 Gigabit Ethernet (rev 03)

lshal shows

Dumping 85 device(s) from the Global Device List:
-------------------------------------------------
udi = '/org/freedesktop/Hal/devices/computer'
  info.addons = {'hald-addon-acpi'} (string list)
  info.callouts.add = {'hal-storage-cleanup-all-mountpoints'} (string list)
  info.interfaces = {'org.freedesktop.Hal.Device.SystemPowerManagement'} (string list)
  info.product = 'Computer'  (string)
  info.subsystem = 'unknown'  (string)
  info.udi = '/org/freedesktop/Hal/devices/computer'  (string)
  org.freedesktop.Hal.Device.SystemPowerManagement.method_argnames = {'num_seconds_to_sleep', 'num_seconds_to_sleep', '', '', '', 'enable_power_save'} (string list)
  org.freedesktop.Hal.Device.SystemPowerManagement.method_execpaths = {'hal-system-power-suspend', 'hal-system-power-suspend-hybrid', 'hal-system-power-hibernate', 'hal-system-power-shutdown', 'hal-system-power-reboot', 'hal-system-power-set-power-save'} (string list)
  org.freedesktop.Hal.Device.SystemPowerManagement.method_names = {'Suspend', 'SuspendHybrid', 'Hibernate', 'Shutdown', 'Reboot', 'SetPowerSave'} (string list)
  org.freedesktop.Hal.Device.SystemPowerManagement.method_signatures = {'i', 'i', '', '', '', 'b'} (string list)
  org.freedesktop.Hal.version = '0.5.13'  (string)
  org.freedesktop.Hal.version.major = 0  (0x0)  (int)
  org.freedesktop.Hal.version.micro = 13  (0xd)  (int)
  org.freedesktop.Hal.version.minor = 5  (0x5)  (int)
  power_management.acpi.linux.version = '20090521'  (string)
  power_management.can_hibernate = true  (bool)
  power_management.can_suspend = true  (bool)
  power_management.can_suspend_hybrid = false  (bool)
  power_management.can_suspend_to_disk = true  (bool)
  power_management.can_suspend_to_ram = true  (bool)
  power_management.is_powersave_set = false  (bool)
  power_management.quirk.dpms_on = true  (bool)
  power_management.quirk.dpms_suspend = true  (bool)
  power_management.quirk.vbe_post = true  (bool)
  power_management.quirk.vbemode_restore = true  (bool)
  power_management.quirk.vbestate_restore = true  (bool)
  power_management.quirk.vga_mode_3 = true  (bool)
  power_management.type = 'acpi'  (string)
  system.board.product = '085Ch'  (string)
  system.board.serial = 'USU3490BR5'  (string)
  system.board.vendor = 'Hewlett-Packard'  (string)
  system.board.version = ''  (string)
  system.chassis.manufacturer = 'Hewlett-Packard'  (string)
  system.chassis.type = 'Mini Tower'  (string)
  system.firmware.release_date = '08/07/2008'  (string)
  system.firmware.vendor = 'Hewlett-Packard'  (string)
  system.firmware.version = '786B2 v2.44'  (string)
  system.formfactor = 'desktop'  (string)
  system.hardware.primary_video.product = 9586  (0x2572)  (int)
  system.hardware.primary_video.vendor = 32902  (0x8086)  (int)
  system.hardware.product = 'HP d530 CMT(dc577av)'  (string)
  system.hardware.serial = 'USU3490BR5'  (string)
  system.hardware.uuid = 'BD0A44D7-CC26-D811-BBD8-9DD967BE000D'  (string)
  system.hardware.vendor = 'Hewlett-Packard'  (string)
  system.hardware.version = ''  (string)
  system.kernel.machine = 'i686'  (string)
  system.kernel.name = 'Linux'  (string)
  system.kernel.version = '2.6.31.5-122.fc12.i686'  (string)
  system.kernel.version.major = 2  (0x2)  (int)
  system.kernel.version.micro = 31  (0x1f)  (int)
  system.kernel.version.minor = 6  (0x6)  (int)

udi = '/org/freedesktop/Hal/devices/acpi_CPU0'
  info.capabilities = {'processor'} (string list)
  info.category = 'processor'  (string)
  info.parent = '/org/freedesktop/Hal/devices/computer'  (string)
  info.product = 'Intel(R) Pentium(R) 4 CPU 2.60GHz'  (string)
  info.udi = '/org/freedesktop/Hal/devices/acpi_CPU0'  (string)
  linux.acpi_path = '/proc/acpi/processor/CPU0'  (string)
  linux.acpi_type = 1  (0x1)  (int)
  linux.hotplug_type = 4  (0x4)  (int)
  processor.can_throttle = true  (bool)
  processor.number = 0  (0x0)  (int)

udi = '/org/freedesktop/Hal/devices/acpi_CPU1'
  info.capabilities = {'processor'} (string list)
  info.category = 'processor'  (string)
  info.parent = '/org/freedesktop/Hal/devices/computer'  (string)
  info.product = 'Intel(R) Pentium(R) 4 CPU 2.60GHz'  (string)
  info.udi = '/org/freedesktop/Hal/devices/acpi_CPU1'  (string)
  linux.acpi_path = '/proc/acpi/processor/CPU1'  (string)
  linux.acpi_type = 1  (0x1)  (int)
  linux.hotplug_type = 4  (0x4)  (int)
  processor.can_throttle = true  (bool)
  processor.number = 1  (0x1)  (int)

udi = '/org/freedesktop/Hal/devices/net_computer_loopback'
  info.capabilities = {'net', 'net.loopback'} (string list)
  info.category = 'net.loopback'  (string)
  info.parent = '/org/freedesktop/Hal/devices/computer'  (string)
  info.product = 'Loopback device Interface'  (string)
  info.subsystem = 'net'  (string)
  info.udi = '/org/freedesktop/Hal/devices/net_computer_loopback'  (string)
  linux.hotplug_type = 2  (0x2)  (int)
  linux.subsystem = 'net'  (string)
  linux.sysfs_path = '/sys/devices/virtual/net/lo'  (string)
  net.address = '00:00:00:00:00:00'  (string)
  net.arp_proto_hw_id = 772  (0x304)  (int)
  net.interface = 'lo'  (string)
  net.linux.ifindex = 1  (0x1)  (int)
  net.originating_device = '/org/freedesktop/Hal/devices/computer'  (string)
  net.physical_device = '/org/freedesktop/Hal/devices/computer'  (string)

udi = '/org/freedesktop/Hal/devices/computer_logicaldev_input_1'
  info.capabilities = {'input', 'input.mouse'} (string list)
  info.category = 'input'  (string)
  info.parent = '/org/freedesktop/Hal/devices/computer'  (string)
  info.product = 'Macintosh mouse button emulation'  (string)
  info.subsystem = 'input'  (string)
  info.udi = '/org/freedesktop/Hal/devices/computer_logicaldev_input_1'  (string)
  input.device = '/dev/input/event2'  (string)
  input.product = 'Macintosh mouse button emulation'  (string)
  input.x11_driver = 'evdev'  (string)
  linux.device_file = '/dev/input/event2'  (string)
  linux.hotplug_type = 2  (0x2)  (int)
  linux.subsystem = 'input'  (string)
  linux.sysfs_path = '/sys/devices/virtual/input/input2/event2'  (string)

udi = '/org/freedesktop/Hal/devices/computer_logicaldev_input_0'
  button.has_state = false  (bool)
  button.type = 'power'  (string)
  info.addons.singleton = {'hald-addon-input'} (string list)
  info.capabilities = {'input', 'button', 'input.keys'} (string list)
  info.category = 'input'  (string)
  info.parent = '/org/freedesktop/Hal/devices/computer'  (string)
  info.product = 'Power Button'  (string)
  info.subsystem = 'input'  (string)
  info.udi = '/org/freedesktop/Hal/devices/computer_logicaldev_input_0'  (string)
  input.device = '/dev/input/event1'  (string)
  input.product = 'Power Button'  (string)
  input.x11_driver = 'evdev'  (string)
  input.xkb.layout = 'us'  (string)
  input.xkb.model = 'evdev'  (string)
  input.xkb.rules = 'base'  (string)
  input.xkb.variant = ''  (string)
  linux.device_file = '/dev/input/event1'  (string)
  linux.hotplug_type = 2  (0x2)  (int)
  linux.subsystem = 'input'  (string)
  linux.sysfs_path = '/sys/devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1/event1'  (string)

udi = '/org/freedesktop/Hal/devices/computer_logicaldev_input'
  button.has_state = false  (bool)
  button.type = 'power'  (string)
  info.addons.singleton = {'hald-addon-input'} (string list)
  info.capabilities = {'input', 'button', 'input.keys'} (string list)
  info.category = 'input'  (string)
  info.parent = '/org/freedesktop/Hal/devices/computer'  (string)
  info.product = 'Power Button'  (string)
  info.subsystem = 'input'  (string)
  info.udi = '/org/freedesktop/Hal/devices/computer_logicaldev_input'  (string)
  input.device = '/dev/input/event0'  (string)
  input.product = 'Power Button'  (string)
  input.x11_driver = 'evdev'  (string)
  input.xkb.layout = 'us'  (string)
  input.xkb.model = 'evdev'  (string)
  input.xkb.rules = 'base'  (string)
  input.xkb.variant = ''  (string)
  linux.device_file = '/dev/input/event0'  (string)
  linux.hotplug_type = 2  (0x2)  (int)
  linux.subsystem = 'input'  (string)
  linux.sysfs_path = '/sys/devices/LNXSYSTM:00/LNXPWRBN:00/input/input0/event0'  (string)

udi = '/org/freedesktop/Hal/devices/pnp_PNP0c01'
  info.linux.driver = 'system'  (string)
  info.parent = '/org/freedesktop/Hal/devices/computer'  (string)
  info.product = 'System Board'  (string)
  info.subsystem = 'pnp'  (string)
  info.udi = '/org/freedesktop/Hal/devices/pnp_PNP0c01'  (string)
  linux.hotplug_type = 2  (0x2)  (int)
  linux.subsystem = 'pnp'  (string)
  linux.sysfs_path = '/sys/devices/pnp0/00:0d'  (string)
  pnp.description = 'System Board'  (string)
  pnp.id = 'PNP0c01'  (string)

udi = '/org/freedesktop/Hal/devices/pnp_PNP0c02_0'
  info.linux.driver = 'system'  (string)
  info.parent = '/org/freedesktop/Hal/devices/computer'  (string)
  info.product = 'General ID for reserving resources required by PnP motherboard registers. (Not device specific.)'  (string)
  info.subsystem = 'pnp'  (string)
  info.udi = '/org/freedesktop/Hal/devices/pnp_PNP0c02_0'  (string)
  linux.hotplug_type = 2  (0x2)  (int)
  linux.subsystem = 'pnp'  (string)
  linux.sysfs_path = '/sys/devices/pnp0/00:0c'  (string)
  pnp.description = 'General ID for reserving resources required by PnP motherboard registers. (Not device specific.)'  (string)
  pnp.id = 'PNP0c02'  (string)

udi = '/org/freedesktop/Hal/devices/pnp_PNP0c02'
  info.linux.driver = 'system'  (string)
  info.parent = '/org/freedesktop/Hal/devices/computer'  (string)
  info.product = 'General ID for reserving resources required by PnP motherboard registers. (Not device specific.)'  (string)
  info.subsystem = 'pnp'  (string)
  info.udi = '/org/freedesktop/Hal/devices/pnp_PNP0c02'  (string)
  linux.hotplug_type = 2  (0x2)  (int)
  linux.subsystem = 'pnp'  (string)
  linux.sysfs_path = '/sys/devices/pnp0/00:0b'  (string)
  pnp.description = 'General ID for reserving resources required by PnP motherboard registers. (Not device specific.)'  (string)
  pnp.id = 'PNP0c02'  (string)

udi = '/org/freedesktop/Hal/devices/pnp_PNP0003'
  info.parent = '/org/freedesktop/Hal/devices/computer'  (string)
  info.product = 'APIC'  (string)
  info.subsystem = 'pnp'  (string)
  info.udi = '/org/freedesktop/Hal/devices/pnp_PNP0003'  (string)
  linux.hotplug_type = 2  (0x2)  (int)
  linux.subsystem = 'pnp'  (string)
  linux.sysfs_path = '/sys/devices/pnp0/00:0a'  (string)
  pnp.description = 'APIC'  (string)
  pnp.id = 'PNP0003'  (string)

udi = '/org/freedesktop/Hal/devices/pnp_PNP0700'
  info.parent = '/org/freedesktop/Hal/devices/computer'  (string)
  info.product = 'PC standard floppy disk controller'  (string)
  info.subsystem = 'pnp'  (string)
  info.udi = '/org/freedesktop/Hal/devices/pnp_PNP0700'  (string)
  linux.hotplug_type = 2  (0x2)  (int)
  linux.subsystem = 'pnp'  (string)
  linux.sysfs_path = '/sys/devices/pnp0/00:09'  (string)
  pnp.description = 'PC standard floppy disk controller'  (string)
  pnp.id = 'PNP0700'  (string)

udi = '/org/freedesktop/Hal/devices/pnp_PNP0501'
  info.linux.driver = 'serial'  (string)
  info.parent = '/org/freedesktop/Hal/devices/computer'  (string)
  info.product = '16550A-compatible COM port'  (string)
  info.subsystem = 'pnp'  (string)
  info.udi = '/org/freedesktop/Hal/devices/pnp_PNP0501'  (string)
  linux.hotplug_type = 2  (0x2)  (int)
  linux.subsystem = 'pnp'  (string)
  linux.sysfs_path = '/sys/devices/pnp0/00:08'  (string)
  pnp.description = '16550A-compatible COM port'  (string)
  pnp.id = 'PNP0501'  (string)

udi = '/org/freedesktop/Hal/devices/pnp_PNP0401'
  info.parent = '/org/freedesktop/Hal/devices/computer'  (string)
  info.product = 'ECP printer port'  (string)
  info.subsystem = 'pnp'  (string)
  info.udi = '/org/freedesktop/Hal/devices/pnp_PNP0401'  (string)
  linux.hotplug_type = 2  (0x2)  (int)
  linux.subsystem = 'pnp'  (string)
  linux.sysfs_path = '/sys/devices/pnp0/00:07'  (string)
  pnp.description = 'ECP printer port'  (string)
  pnp.id = 'PNP0401'  (string)

udi = '/org/freedesktop/Hal/devices/pnp_PNP0303'
  info.linux.driver = 'i8042 kbd'  (string)
  info.parent = '/org/freedesktop/Hal/devices/computer'  (string)
  info.product = 'IBM Enhanced (101/102-key, PS/2 mouse support)'  (string)
  info.subsystem = 'pnp'  (string)
  info.udi = '/org/freedesktop/Hal/devices/pnp_PNP0303'  (string)
  linux.hotplug_type = 2  (0x2)  (int)
  linux.subsystem = 'pnp'  (string)
  linux.sysfs_path = '/sys/devices/pnp0/00:06'  (string)
  pnp.description = 'IBM Enhanced (101/102-key, PS/2 mouse support)'  (string)
  pnp.id = 'PNP0303'  (string)

udi = '/org/freedesktop/Hal/devices/pnp_PNP0f13'
  info.linux.driver = 'i8042 aux'  (string)
  info.parent = '/org/freedesktop/Hal/devices/computer'  (string)
  info.product = 'PS/2 Port for PS/2-style Mice'  (string)
  info.subsystem = 'pnp'  (string)
  info.udi = '/org/freedesktop/Hal/devices/pnp_PNP0f13'  (string)
  linux.hotplug_type = 2  (0x2)  (int)
  linux.subsystem = 'pnp'  (string)
  linux.sysfs_path = '/sys/devices/pnp0/00:05'  (string)
  pnp.description = 'PS/2 Port for PS/2-style Mice'  (string)
  pnp.id = 'PNP0f13'  (string)

udi = '/org/freedesktop/Hal/devices/pnp_PNP0800'
  info.parent = '/org/freedesktop/Hal/devices/computer'  (string)
  info.product = 'AT-style speaker sound'  (string)
  info.subsystem = 'pnp'  (string)
  info.udi = '/org/freedesktop/Hal/devices/pnp_PNP0800'  (string)
  linux.hotplug_type = 2  (0x2)  (int)
  linux.subsystem = 'pnp'  (string)
  linux.sysfs_path = '/sys/devices/pnp0/00:04'  (string)
  pnp.description = 'AT-style speaker sound'  (string)
  pnp.id = 'PNP0800'  (string)

udi = '/org/freedesktop/Hal/devices/pnp_PNP0b00'
  info.linux.driver = 'rtc_cmos'  (string)
  info.parent = '/org/freedesktop/Hal/devices/computer'  (string)
  info.product = 'AT Real-Time Clock'  (string)
  info.subsystem = 'pnp'  (string)
  info.udi = '/org/freedesktop/Hal/devices/pnp_PNP0b00'  (string)
  linux.hotplug_type = 2  (0x2)  (int)
  linux.subsystem = 'pnp'  (string)
  linux.sysfs_path = '/sys/devices/pnp0/00:03'  (string)
  pnp.description = 'AT Real-Time Clock'  (string)
  pnp.id = 'PNP0b00'  (string)

udi = '/org/freedesktop/Hal/devices/pnp_PNP0200'
  info.parent = '/org/freedesktop/Hal/devices/computer'  (string)
  info.product = 'AT DMA Controller'  (string)
  info.subsystem = 'pnp'  (string)
  info.udi = '/org/freedesktop/Hal/devices/pnp_PNP0200'  (string)
  linux.hotplug_type = 2  (0x2)  (int)
  linux.subsystem = 'pnp'  (string)
  linux.sysfs_path = '/sys/devices/pnp0/00:02'  (string)
  pnp.description = 'AT DMA Controller'  (string)
  pnp.id = 'PNP0200'  (string)

udi = '/org/freedesktop/Hal/devices/pnp_PNP0c04'
  info.parent = '/org/freedesktop/Hal/devices/computer'  (string)
  info.product = 'Math Coprocessor'  (string)
  info.subsystem = 'pnp'  (string)
  info.udi = '/org/freedesktop/Hal/devices/pnp_PNP0c04'  (string)
  linux.hotplug_type = 2  (0x2)  (int)
  linux.subsystem = 'pnp'  (string)
  linux.sysfs_path = '/sys/devices/pnp0/00:01'  (string)
  pnp.description = 'Math Coprocessor'  (string)
  pnp.id = 'PNP0c04'  (string)

udi = '/org/freedesktop/Hal/devices/pnp_PNP0a03'
  info.parent = '/org/freedesktop/Hal/devices/computer'  (string)
  info.product = 'PCI Bus'  (string)
  info.subsystem = 'pnp'  (string)
  info.udi = '/org/freedesktop/Hal/devices/pnp_PNP0a03'  (string)
  linux.hotplug_type = 2  (0x2)  (int)
  linux.subsystem = 'pnp'  (string)
  linux.sysfs_path = '/sys/devices/pnp0/00:00'  (string)
  pnp.description = 'PCI Bus'  (string)
  pnp.id = 'PNP0a03'  (string)

udi = '/org/freedesktop/Hal/devices/platform_vesafb_0'
  info.parent = '/org/freedesktop/Hal/devices/computer'  (string)
  info.product = 'Platform Device (vesafb.0)'  (string)
  info.subsystem = 'platform'  (string)
  info.udi = '/org/freedesktop/Hal/devices/platform_vesafb_0'  (string)
  linux.hotplug_type = 2  (0x2)  (int)
  linux.subsystem = 'platform'  (string)
  linux.sysfs_path = '/sys/devices/platform/vesafb.0'  (string)
  platform.id = 'vesafb.0'  (string)

udi = '/org/freedesktop/Hal/devices/platform_serial8250'
  info.linux.driver = 'serial8250'  (string)
  info.parent = '/org/freedesktop/Hal/devices/computer'  (string)
  info.product = 'Platform Device (serial8250)'  (string)
  info.subsystem = 'platform'  (string)
  info.udi = '/org/freedesktop/Hal/devices/platform_serial8250'  (string)
  linux.hotplug_type = 2  (0x2)  (int)
  linux.subsystem = 'platform'  (string)
  linux.sysfs_path = '/sys/devices/platform/serial8250'  (string)
  platform.id = 'serial8250'  (string)

udi = '/org/freedesktop/Hal/devices/platform_pcspkr'
  info.linux.driver = 'pcspkr'  (string)
  info.parent = '/org/freedesktop/Hal/devices/computer'  (string)
  info.product = 'Platform Device (pcspkr)'  (string)
  info.subsystem = 'platform'  (string)
  info.udi = '/org/freedesktop/Hal/devices/platform_pcspkr'  (string)
  linux.hotplug_type = 2  (0x2)  (int)
  linux.subsystem = 'platform'  (string)
  linux.sysfs_path = '/sys/devices/platform/pcspkr'  (string)
  platform.id = 'pcspkr'  (string)

udi = '/org/freedesktop/Hal/devices/platform_pcspkr_logicaldev_input'
  info.capabilities = {'input'} (string list)
  info.category = 'input'  (string)
  info.parent = '/org/freedesktop/Hal/devices/platform_pcspkr'  (string)
  info.product = 'PC Speaker'  (string)
  info.subsystem = 'input'  (string)
  info.udi = '/org/freedesktop/Hal/devices/platform_pcspkr_logicaldev_input'  (string)
  input.device = '/dev/input/event5'  (string)
  input.originating_device = '/org/freedesktop/Hal/devices/platform_pcspkr'  (string)
  input.product = 'PC Speaker'  (string)
  linux.device_file = '/dev/input/event5'  (string)
  linux.hotplug_type = 2  (0x2)  (int)
  linux.subsystem = 'input'  (string)
  linux.sysfs_path = '/sys/devices/platform/pcspkr/input/input5/event5'  (string)

udi = '/org/freedesktop/Hal/devices/platform_i8042'
  info.linux.driver = 'i8042'  (string)
  info.parent = '/org/freedesktop/Hal/devices/computer'  (string)
  info.product = 'Platform Device (i8042)'  (string)
  info.subsystem = 'platform'  (string)
  info.udi = '/org/freedesktop/Hal/devices/platform_i8042'  (string)
  linux.hotplug_type = 2  (0x2)  (int)
  linux.subsystem = 'platform'  (string)
  linux.sysfs_path = '/sys/devices/platform/i8042'  (string)
  platform.id = 'i8042'  (string)

udi = '/org/freedesktop/Hal/devices/platform_i8042_i8042_AUX_port'
  info.linux.driver = 'psmouse'  (string)
  info.parent = '/org/freedesktop/Hal/devices/platform_i8042'  (string)
  info.product = 'i8042 AUX port'  (string)
  info.subsystem = 'serio'  (string)
  info.udi = '/org/freedesktop/Hal/devices/platform_i8042_i8042_AUX_port'  (string)
  linux.hotplug_type = 2  (0x2)  (int)
  linux.subsystem = 'serio'  (string)
  linux.sysfs_path = '/sys/devices/platform/i8042/serio1'  (string)
  serio.description = 'i8042 AUX port'  (string)
  serio.id = 'serio1'  (string)

udi = '/org/freedesktop/Hal/devices/platform_i8042_i8042_AUX_port_logicaldev_input'
  info.callouts.add = {'hal-probe-vmmouse'} (string list)
  info.capabilities = {'input', 'input.mouse'} (string list)
  info.category = 'input'  (string)
  info.parent = '/org/freedesktop/Hal/devices/platform_i8042_i8042_AUX_port'  (string)
  info.product = 'ImExPS/2 Logitech Wheel Mouse'  (string)
  info.subsystem = 'input'  (string)
  info.udi = '/org/freedesktop/Hal/devices/platform_i8042_i8042_AUX_port_logicaldev_input'  (string)
  input.device = '/dev/input/event4'  (string)
  input.originating_device = '/org/freedesktop/Hal/devices/platform_i8042_i8042_AUX_port'  (string)
  input.product = 'ImExPS/2 Logitech Wheel Mouse'  (string)
  input.x11_driver = 'evdev'  (string)
  linux.device_file = '/dev/input/event4'  (string)
  linux.hotplug_type = 2  (0x2)  (int)
  linux.subsystem = 'input'  (string)
  linux.sysfs_path = '/sys/devices/platform/i8042/serio1/input/input4/event4'  (string)

udi = '/org/freedesktop/Hal/devices/platform_i8042_i8042_KBD_port'
  info.linux.driver = 'atkbd'  (string)
  info.parent = '/org/freedesktop/Hal/devices/platform_i8042'  (string)
  info.product = 'i8042 KBD port'  (string)
  info.subsystem = 'serio'  (string)
  info.udi = '/org/freedesktop/Hal/devices/platform_i8042_i8042_KBD_port'  (string)
  linux.hotplug_type = 2  (0x2)  (int)
  linux.subsystem = 'serio'  (string)
  linux.sysfs_path = '/sys/devices/platform/i8042/serio0'  (string)
  serio.description = 'i8042 KBD port'  (string)
  serio.id = 'serio0'  (string)

udi = '/org/freedesktop/Hal/devices/platform_i8042_i8042_KBD_port_logicaldev_input'
  info.addons.singleton = {'hald-addon-input'} (string list)
  info.callouts.add = {'fedora-setup-keyboard'} (string list)
  info.capabilities = {'input', 'input.keyboard', 'input.keypad', 'input.keys', 'button'} (string list)
  info.category = 'input'  (string)
  info.parent = '/org/freedesktop/Hal/devices/platform_i8042_i8042_KBD_port'  (string)
  info.product = 'AT Translated Set 2 keyboard'  (string)
  info.subsystem = 'input'  (string)
  info.udi = '/org/freedesktop/Hal/devices/platform_i8042_i8042_KBD_port_logicaldev_input'  (string)
  input.device = '/dev/input/event3'  (string)
  input.originating_device = '/org/freedesktop/Hal/devices/platform_i8042_i8042_KBD_port'  (string)
  input.product = 'AT Translated Set 2 keyboard'  (string)
  input.x11_driver = 'evdev'  (string)
  input.xkb.layout = 'us'  (string)
  input.xkb.model = 'evdev'  (string)
  input.xkb.options = 'terminate:ctrl_alt_bksp'  (string)
  input.xkb.rules = 'base'  (string)
  input.xkb.variant = ''  (string)
  linux.device_file = '/dev/input/event3'  (string)
  linux.hotplug_type = 2  (0x2)  (int)
  linux.subsystem = 'input'  (string)
  linux.sysfs_path = '/sys/devices/platform/i8042/serio0/input/input3/event3'  (string)

udi = '/org/freedesktop/Hal/devices/platform_floppy_0'
  info.linux.driver = 'floppy'  (string)
  info.parent = '/org/freedesktop/Hal/devices/computer'  (string)
  info.product = 'Platform Device (floppy.0)'  (string)
  info.subsystem = 'platform'  (string)
  info.udi = '/org/freedesktop/Hal/devices/platform_floppy_0'  (string)
  linux.hotplug_type = 2  (0x2)  (int)
  linux.subsystem = 'platform'  (string)
  linux.sysfs_path = '/sys/devices/platform/floppy.0'  (string)
  platform.id = 'floppy.0'  (string)

udi = '/org/freedesktop/Hal/devices/platform_Fixed_MDIO_bus_0'
  info.parent = '/org/freedesktop/Hal/devices/computer'  (string)
  info.product = 'Platform Device (Fixed MDIO bus.0)'  (string)
  info.subsystem = 'platform'  (string)
  info.udi = '/org/freedesktop/Hal/devices/platform_Fixed_MDIO_bus_0'  (string)
  linux.hotplug_type = 2  (0x2)  (int)
  linux.subsystem = 'platform'  (string)
  linux.sysfs_path = '/sys/devices/platform/Fixed MDIO bus.0'  (string)
  platform.id = 'Fixed MDIO bus.0'  (string)

udi = '/org/freedesktop/Hal/devices/pci_8086_24d5'
  info.parent = '/org/freedesktop/Hal/devices/computer'  (string)
  info.product = '82801EB/ER (ICH5/ICH5R) AC'97 Audio Controller'  (string)
  info.subsystem = 'pci'  (string)
  info.udi = '/org/freedesktop/Hal/devices/pci_8086_24d5'  (string)
  info.vendor = 'Intel Corporation'  (string)
  linux.hotplug_type = 2  (0x2)  (int)
  linux.subsystem = 'pci'  (string)
  linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1f.5'  (string)
  pci.device_class = 4  (0x4)  (int)
  pci.device_protocol = 0  (0x0)  (int)
  pci.device_subclass = 1  (0x1)  (int)
  pci.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1f.5'  (string)
  pci.product = '82801EB/ER (ICH5/ICH5R) AC'97 Audio Controller'  (string)
  pci.product_id = 9429  (0x24d5)  (int)
  pci.subsys_product = 'd330 uT'  (string)
  pci.subsys_product_id = 4796  (0x12bc)  (int)
  pci.subsys_vendor = 'Hewlett-Packard Company'  (string)
  pci.subsys_vendor_id = 4156  (0x103c)  (int)
  pci.vendor = 'Intel Corporation'  (string)
  pci.vendor_id = 32902  (0x8086)  (int)

udi = '/org/freedesktop/Hal/devices/pci_8086_24d3'
  info.parent = '/org/freedesktop/Hal/devices/computer'  (string)
  info.product = '82801EB/ER (ICH5/ICH5R) SMBus Controller'  (string)
  info.subsystem = 'pci'  (string)
  info.udi = '/org/freedesktop/Hal/devices/pci_8086_24d3'  (string)
  info.vendor = 'Intel Corporation'  (string)
  linux.hotplug_type = 2  (0x2)  (int)
  linux.subsystem = 'pci'  (string)
  linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1f.3'  (string)
  pci.device_class = 12  (0xc)  (int)
  pci.device_protocol = 0  (0x0)  (int)
  pci.device_subclass = 5  (0x5)  (int)
  pci.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1f.3'  (string)
  pci.product = '82801EB/ER (ICH5/ICH5R) SMBus Controller'  (string)
  pci.product_id = 9427  (0x24d3)  (int)
  pci.subsys_product = 'd330 uT'  (string)
  pci.subsys_product_id = 4796  (0x12bc)  (int)
  pci.subsys_vendor = 'Hewlett-Packard Company'  (string)
  pci.subsys_vendor_id = 4156  (0x103c)  (int)
  pci.vendor = 'Intel Corporation'  (string)
  pci.vendor_id = 32902  (0x8086)  (int)

udi = '/org/freedesktop/Hal/devices/pci_8086_24d1'
  info.linux.driver = 'ata_piix'  (string)
  info.parent = '/org/freedesktop/Hal/devices/computer'  (string)
  info.product = '82801EB (ICH5) SATA Controller'  (string)
  info.subsystem = 'pci'  (string)
  info.udi = '/org/freedesktop/Hal/devices/pci_8086_24d1'  (string)
  info.vendor = 'Intel Corporation'  (string)
  linux.hotplug_type = 2  (0x2)  (int)
  linux.subsystem = 'pci'  (string)
  linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1f.2'  (string)
  pci.device_class = 1  (0x1)  (int)
  pci.device_protocol = 143  (0x8f)  (int)
  pci.device_subclass = 1  (0x1)  (int)
  pci.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1f.2'  (string)
  pci.product = '82801EB (ICH5) SATA Controller'  (string)
  pci.product_id = 9425  (0x24d1)  (int)
  pci.subsys_product = 'd530 CMT (DG746A)'  (string)
  pci.subsys_product_id = 4796  (0x12bc)  (int)
  pci.subsys_vendor = 'Hewlett-Packard Company'  (string)
  pci.subsys_vendor_id = 4156  (0x103c)  (int)
  pci.vendor = 'Intel Corporation'  (string)
  pci.vendor_id = 32902  (0x8086)  (int)

udi = '/org/freedesktop/Hal/devices/pci_8086_24d1_scsi_host_0'
  info.capabilities = {'scsi_host'} (string list)
  info.category = 'scsi_host'  (string)
  info.parent = '/org/freedesktop/Hal/devices/pci_8086_24d1'  (string)
  info.product = 'SCSI Host Adapter'  (string)
  info.subsystem = 'scsi_host'  (string)
  info.udi = '/org/freedesktop/Hal/devices/pci_8086_24d1_scsi_host_0'  (string)
  linux.hotplug_type = 2  (0x2)  (int)
  linux.subsystem = 'scsi_host'  (string)
  linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1f.2/host3/scsi_host/host3'  (string)
  scsi_host.host = 3  (0x3)  (int)

udi = '/org/freedesktop/Hal/devices/pci_8086_24d1_scsi_host'
  info.capabilities = {'scsi_host'} (string list)
  info.category = 'scsi_host'  (string)
  info.parent = '/org/freedesktop/Hal/devices/pci_8086_24d1'  (string)
  info.product = 'SCSI Host Adapter'  (string)
  info.subsystem = 'scsi_host'  (string)
  info.udi = '/org/freedesktop/Hal/devices/pci_8086_24d1_scsi_host'  (string)
  linux.hotplug_type = 2  (0x2)  (int)
  linux.subsystem = 'scsi_host'  (string)
  linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1f.2/host2'  (string)
  scsi_host.host = 2  (0x2)  (int)

udi = '/org/freedesktop/Hal/devices/pci_8086_24d1_scsi_host_scsi_host'
  info.capabilities = {'scsi_host'} (string list)
  info.category = 'scsi_host'  (string)
  info.parent = '/org/freedesktop/Hal/devices/pci_8086_24d1_scsi_host'  (string)
  info.product = 'SCSI Host Adapter'  (string)
  info.subsystem = 'scsi_host'  (string)
  info.udi = '/org/freedesktop/Hal/devices/pci_8086_24d1_scsi_host_scsi_host'  (string)
  linux.hotplug_type = 2  (0x2)  (int)
  linux.subsystem = 'scsi_host'  (string)
  linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1f.2/host2/scsi_host/host2'  (string)
  scsi_host.host = 2  (0x2)  (int)

udi = '/org/freedesktop/Hal/devices/pci_8086_24d1_scsi_host_scsi_device_lun0'
  info.linux.driver = 'sd'  (string)
  info.parent = '/org/freedesktop/Hal/devices/pci_8086_24d1_scsi_host'  (string)
  info.product = 'SCSI Device'  (string)
  info.subsystem = 'scsi'  (string)
  info.udi = '/org/freedesktop/Hal/devices/pci_8086_24d1_scsi_host_scsi_device_lun0'  (string)
  linux.hotplug_type = 2  (0x2)  (int)
  linux.subsystem = 'scsi'  (string)
  linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1f.2/host2/target2:0:0/2:0:0:0'  (string)
  scsi.bus = 0  (0x0)  (int)
  scsi.host = 2  (0x2)  (int)
  scsi.lun = 0  (0x0)  (int)
  scsi.model = 'ST3500320AS'  (string)
  scsi.target = 0  (0x0)  (int)
  scsi.type = 'disk'  (string)
  scsi.vendor = 'ATA'  (string)

udi = '/org/freedesktop/Hal/devices/storage_model_ST3500320AS'
  block.device = '/dev/sdb'  (string)
  block.is_volume = false  (bool)
  block.major = 8  (0x8)  (int)
  block.minor = 16  (0x10)  (int)
  block.storage_device = '/org/freedesktop/Hal/devices/storage_model_ST3500320AS'  (string)
  info.capabilities = {'storage', 'block'} (string list)
  info.category = 'storage'  (string)
  info.parent = '/org/freedesktop/Hal/devices/pci_8086_24d1_scsi_host_scsi_device_lun0'  (string)
  info.product = 'ST3500320AS'  (string)
  info.udi = '/org/freedesktop/Hal/devices/storage_model_ST3500320AS'  (string)
  info.vendor = 'ATA'  (string)
  linux.hotplug_type = 3  (0x3)  (int)
  linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1f.2/host2/target2:0:0/2:0:0:0/block/sdb'  (string)
  storage.automount_enabled_hint = true  (bool)
  storage.bus = 'pci'  (string)
  storage.drive_type = 'disk'  (string)
  storage.hotpluggable = false  (bool)
  storage.lun = 0  (0x0)  (int)
  storage.media_check_enabled = false  (bool)
  storage.model = 'ST3500320AS'  (string)
  storage.no_partitions_hint = false  (bool)
  storage.originating_device = '/org/freedesktop/Hal/devices/computer'  (string)
  storage.partitioning_scheme = 'mbr'  (string)
  storage.removable = false  (bool)
  storage.removable.media_available = true  (bool)
  storage.removable.media_size = 500107862016  (0x7470c06000)  (uint64)
  storage.requires_eject = false  (bool)
  storage.size = 500107862016  (0x7470c06000)  (uint64)
  storage.vendor = 'ATA'  (string)

udi = '/org/freedesktop/Hal/devices/pci_8086_24d1_scsi_host_scsi_device_lun0_scsi_generic'
  info.capabilities = {'scsi_generic'} (string list)
  info.category = 'scsi_generic'  (string)
  info.parent = '/org/freedesktop/Hal/devices/pci_8086_24d1_scsi_host_scsi_device_lun0'  (string)
  info.product = 'SCSI Generic Interface'  (string)
  info.subsystem = 'scsi_generic'  (string)
  info.udi = '/org/freedesktop/Hal/devices/pci_8086_24d1_scsi_host_scsi_device_lun0_scsi_generic'  (string)
  linux.device_file = '/dev/sg2'  (string)
  linux.hotplug_type = 2  (0x2)  (int)
  linux.subsystem = 'scsi_generic'  (string)
  linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1f.2/host2/target2:0:0/2:0:0:0/scsi_generic/sg2'  (string)
  scsi_generic.device = '/dev/sg2'  (string)

udi = '/org/freedesktop/Hal/devices/pci_8086_24db'
  info.linux.driver = 'ata_piix'  (string)
  info.parent = '/org/freedesktop/Hal/devices/computer'  (string)
  info.product = '82801EB/ER (ICH5/ICH5R) IDE Controller'  (string)
  info.subsystem = 'pci'  (string)
  info.udi = '/org/freedesktop/Hal/devices/pci_8086_24db'  (string)
  info.vendor = 'Intel Corporation'  (string)
  linux.hotplug_type = 2  (0x2)  (int)
  linux.subsystem = 'pci'  (string)
  linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1f.1'  (string)
  pci.device_class = 1  (0x1)  (int)
  pci.device_protocol = 138  (0x8a)  (int)
  pci.device_subclass = 1  (0x1)  (int)
  pci.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1f.1'  (string)
  pci.product = '82801EB/ER (ICH5/ICH5R) IDE Controller'  (string)
  pci.product_id = 9435  (0x24db)  (int)
  pci.subsys_product = 'd530 CMT (DG746A)'  (string)
  pci.subsys_product_id = 4796  (0x12bc)  (int)
  pci.subsys_vendor = 'Hewlett-Packard Company'  (string)
  pci.subsys_vendor_id = 4156  (0x103c)  (int)
  pci.vendor = 'Intel Corporation'  (string)
  pci.vendor_id = 32902  (0x8086)  (int)

udi = '/org/freedesktop/Hal/devices/pci_8086_24db_scsi_host_0'
  info.capabilities = {'scsi_host'} (string list)
  info.category = 'scsi_host'  (string)
  info.parent = '/org/freedesktop/Hal/devices/pci_8086_24db'  (string)
  info.product = 'SCSI Host Adapter'  (string)
  info.subsystem = 'scsi_host'  (string)
  info.udi = '/org/freedesktop/Hal/devices/pci_8086_24db_scsi_host_0'  (string)
  linux.hotplug_type = 2  (0x2)  (int)
  linux.subsystem = 'scsi_host'  (string)
  linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1f.1/host1'  (string)
  scsi_host.host = 1  (0x1)  (int)

udi = '/org/freedesktop/Hal/devices/pci_8086_24db_scsi_host_0_scsi_host'
  info.capabilities = {'scsi_host'} (string list)
  info.category = 'scsi_host'  (string)
  info.parent = '/org/freedesktop/Hal/devices/pci_8086_24db_scsi_host_0'  (string)
  info.product = 'SCSI Host Adapter'  (string)
  info.subsystem = 'scsi_host'  (string)
  info.udi = '/org/freedesktop/Hal/devices/pci_8086_24db_scsi_host_0_scsi_host'  (string)
  linux.hotplug_type = 2  (0x2)  (int)
  linux.subsystem = 'scsi_host'  (string)
  linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1f.1/host1/scsi_host/host1'  (string)
  scsi_host.host = 1  (0x1)  (int)

udi = '/org/freedesktop/Hal/devices/pci_8086_24db_scsi_host_0_scsi_device_lun0'
  info.linux.driver = 'sr'  (string)
  info.parent = '/org/freedesktop/Hal/devices/pci_8086_24db_scsi_host_0'  (string)
  info.product = 'SCSI Device'  (string)
  info.subsystem = 'scsi'  (string)
  info.udi = '/org/freedesktop/Hal/devices/pci_8086_24db_scsi_host_0_scsi_device_lun0'  (string)
  linux.hotplug_type = 2  (0x2)  (int)
  linux.subsystem = 'scsi'  (string)
  linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1f.1/host1/target1:0:0/1:0:0:0'  (string)
  scsi.bus = 0  (0x0)  (int)
  scsi.host = 1  (0x1)  (int)
  scsi.lun = 0  (0x0)  (int)
  scsi.model = 'XJ-HD166S'  (string)
  scsi.target = 0  (0x0)  (int)
  scsi.type = 'cdrom'  (string)
  scsi.vendor = 'JLMS'  (string)

udi = '/org/freedesktop/Hal/devices/storage_model_XJ_HD166S'
  block.device = '/dev/sr0'  (string)
  block.is_volume = false  (bool)
  block.major = 11  (0xb)  (int)
  block.minor = 0  (0x0)  (int)
  block.storage_device = '/org/freedesktop/Hal/devices/storage_model_XJ_HD166S'  (string)
  info.addons = {'hald-addon-storage'} (string list)
  info.capabilities = {'storage', 'block', 'storage.cdrom'} (string list)
  info.category = 'storage'  (string)
  info.interfaces = {'org.freedesktop.Hal.Device.Storage', 'org.freedesktop.Hal.Device.Storage', 'org.freedesktop.Hal.Device.Storage.Removable'} (string list)
  info.parent = '/org/freedesktop/Hal/devices/pci_8086_24db_scsi_host_0_scsi_device_lun0'  (string)
  info.product = 'XJ-HD166S'  (string)
  info.udi = '/org/freedesktop/Hal/devices/storage_model_XJ_HD166S'  (string)
  info.vendor = 'JLMS'  (string)
  linux.hotplug_type = 3  (0x3)  (int)
  linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1f.1/host1/target1:0:0/1:0:0:0/block/sr0'  (string)
  org.freedesktop.Hal.Device.Storage.method_argnames = {'extra_options', 'extra_options'} (string list)
  org.freedesktop.Hal.Device.Storage.method_execpaths = {'hal-storage-eject', 'hal-storage-closetray'} (string list)
  org.freedesktop.Hal.Device.Storage.method_names = {'Eject', 'CloseTray'} (string list)
  org.freedesktop.Hal.Device.Storage.method_signatures = {'as', 'as'} (string list)
  storage.automount_enabled_hint = true  (bool)
  storage.bus = 'pci'  (string)
  storage.cdrom.bd = false  (bool)
  storage.cdrom.bdr = false  (bool)
  storage.cdrom.bdre = false  (bool)
  storage.cdrom.cdr = false  (bool)
  storage.cdrom.cdrw = false  (bool)
  storage.cdrom.dvd = true  (bool)
  storage.cdrom.dvdplusr = false  (bool)
  storage.cdrom.dvdplusrdl = false  (bool)
  storage.cdrom.dvdplusrw = false  (bool)
  storage.cdrom.dvdplusrwdl = false  (bool)
  storage.cdrom.dvdr = false  (bool)
  storage.cdrom.dvdram = false  (bool)
  storage.cdrom.dvdrdl = false  (bool)
  storage.cdrom.dvdrw = false  (bool)
  storage.cdrom.hddvd = false  (bool)
  storage.cdrom.hddvdr = false  (bool)
  storage.cdrom.hddvdrw = false  (bool)
  storage.cdrom.mo = false  (bool)
  storage.cdrom.mrw = true  (bool)
  storage.cdrom.mrw_w = true  (bool)
  storage.cdrom.read_speed = 7056  (0x1b90)  (int)
  storage.cdrom.support_media_changed = true  (bool)
  storage.cdrom.support_multisession = true  (bool)
  storage.cdrom.write_speed = 0  (0x0)  (int)
  storage.cdrom.write_speeds = {} (string list)
  storage.drive_type = 'cdrom'  (string)
  storage.hotpluggable = false  (bool)
  storage.lun = 0  (0x0)  (int)
  storage.media_check_enabled = true  (bool)
  storage.model = 'XJ-HD166S'  (string)
  storage.no_partitions_hint = true  (bool)
  storage.originating_device = '/org/freedesktop/Hal/devices/computer'  (string)
  storage.removable = true  (bool)
  storage.removable.media_available = true  (bool)
  storage.removable.media_size = 728043520  (0x2b651000)  (uint64)
  storage.removable.support_async_notification = false  (bool)
  storage.requires_eject = true  (bool)
  storage.size = 0  (0x0)  (uint64)
  storage.vendor = 'JLMS'  (string)

udi = '/org/freedesktop/Hal/devices/pci_8086_24db_scsi_host_0_scsi_device_lun0_scsi_generic'
  info.capabilities = {'scsi_generic'} (string list)
  info.category = 'scsi_generic'  (string)
  info.parent = '/org/freedesktop/Hal/devices/pci_8086_24db_scsi_host_0_scsi_device_lun0'  (string)
  info.product = 'SCSI Generic Interface'  (string)
  info.subsystem = 'scsi_generic'  (string)
  info.udi = '/org/freedesktop/Hal/devices/pci_8086_24db_scsi_host_0_scsi_device_lun0_scsi_generic'  (string)
  linux.device_file = '/dev/sg1'  (string)
  linux.hotplug_type = 2  (0x2)  (int)
  linux.subsystem = 'scsi_generic'  (string)
  linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1f.1/host1/target1:0:0/1:0:0:0/scsi_generic/sg1'  (string)
  scsi_generic.device = '/dev/sg1'  (string)

udi = '/org/freedesktop/Hal/devices/pci_8086_24db_scsi_host'
  info.capabilities = {'scsi_host'} (string list)
  info.category = 'scsi_host'  (string)
  info.parent = '/org/freedesktop/Hal/devices/pci_8086_24db'  (string)
  info.product = 'SCSI Host Adapter'  (string)
  info.subsystem = 'scsi_host'  (string)
  info.udi = '/org/freedesktop/Hal/devices/pci_8086_24db_scsi_host'  (string)
  linux.hotplug_type = 2  (0x2)  (int)
  linux.subsystem = 'scsi_host'  (string)
  linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1f.1/host0'  (string)
  scsi_host.host = 0  (0x0)  (int)

udi = '/org/freedesktop/Hal/devices/pci_8086_24db_scsi_host_scsi_host'
  info.capabilities = {'scsi_host'} (string list)
  info.category = 'scsi_host'  (string)
  info.parent = '/org/freedesktop/Hal/devices/pci_8086_24db_scsi_host'  (string)
  info.product = 'SCSI Host Adapter'  (string)
  info.subsystem = 'scsi_host'  (string)
  info.udi = '/org/freedesktop/Hal/devices/pci_8086_24db_scsi_host_scsi_host'  (string)
  linux.hotplug_type = 2  (0x2)  (int)
  linux.subsystem = 'scsi_host'  (string)
  linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1f.1/host0/scsi_host/host0'  (string)
  scsi_host.host = 0  (0x0)  (int)

udi = '/org/freedesktop/Hal/devices/pci_8086_24db_scsi_host_scsi_device_lun0'
  info.linux.driver = 'sd'  (string)
  info.parent = '/org/freedesktop/Hal/devices/pci_8086_24db_scsi_host'  (string)
  info.product = 'SCSI Device'  (string)
  info.subsystem = 'scsi'  (string)
  info.udi = '/org/freedesktop/Hal/devices/pci_8086_24db_scsi_host_scsi_device_lun0'  (string)
  linux.hotplug_type = 2  (0x2)  (int)
  linux.subsystem = 'scsi'  (string)
  linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1f.1/host0/target0:0:0/0:0:0:0'  (string)
  scsi.bus = 0  (0x0)  (int)
  scsi.host = 0  (0x0)  (int)
  scsi.lun = 0  (0x0)  (int)
  scsi.model = 'Maxtor 6E040L0'  (string)
  scsi.target = 0  (0x0)  (int)
  scsi.type = 'disk'  (string)
  scsi.vendor = 'ATA'  (string)

udi = '/org/freedesktop/Hal/devices/storage_model_Maxtor_6E040L0'
  block.device = '/dev/sda'  (string)
  block.is_volume = false  (bool)
  block.major = 8  (0x8)  (int)
  block.minor = 0  (0x0)  (int)
  block.storage_device = '/org/freedesktop/Hal/devices/storage_model_Maxtor_6E040L0'  (string)
  info.capabilities = {'storage', 'block'} (string list)
  info.category = 'storage'  (string)
  info.parent = '/org/freedesktop/Hal/devices/pci_8086_24db_scsi_host_scsi_device_lun0'  (string)
  info.product = 'Maxtor 6E040L0'  (string)
  info.udi = '/org/freedesktop/Hal/devices/storage_model_Maxtor_6E040L0'  (string)
  info.vendor = 'ATA'  (string)
  linux.hotplug_type = 3  (0x3)  (int)
  linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1f.1/host0/target0:0:0/0:0:0:0/block/sda'  (string)
  storage.automount_enabled_hint = true  (bool)
  storage.bus = 'pci'  (string)
  storage.drive_type = 'disk'  (string)
  storage.hotpluggable = false  (bool)
  storage.lun = 0  (0x0)  (int)
  storage.media_check_enabled = false  (bool)
  storage.model = 'Maxtor 6E040L0'  (string)
  storage.no_partitions_hint = false  (bool)
  storage.originating_device = '/org/freedesktop/Hal/devices/computer'  (string)
  storage.partitioning_scheme = 'mbr'  (string)
  storage.removable = false  (bool)
  storage.removable.media_available = true  (bool)
  storage.removable.media_size = 40020664320  (0x9516ae000)  (uint64)
  storage.requires_eject = false  (bool)
  storage.size = 40020664320  (0x9516ae000)  (uint64)
  storage.vendor = 'ATA'  (string)

udi = '/org/freedesktop/Hal/devices/pci_8086_24db_scsi_host_scsi_device_lun0_scsi_generic'
  info.capabilities = {'scsi_generic'} (string list)
  info.category = 'scsi_generic'  (string)
  info.parent = '/org/freedesktop/Hal/devices/pci_8086_24db_scsi_host_scsi_device_lun0'  (string)
  info.product = 'SCSI Generic Interface'  (string)
  info.subsystem = 'scsi_generic'  (string)
  info.udi = '/org/freedesktop/Hal/devices/pci_8086_24db_scsi_host_scsi_device_lun0_scsi_generic'  (string)
  linux.device_file = '/dev/sg0'  (string)
  linux.hotplug_type = 2  (0x2)  (int)
  linux.subsystem = 'scsi_generic'  (string)
  linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1f.1/host0/target0:0:0/0:0:0:0/scsi_generic/sg0'  (string)
  scsi_generic.device = '/dev/sg0'  (string)

udi = '/org/freedesktop/Hal/devices/pci_8086_24d0'
  info.parent = '/org/freedesktop/Hal/devices/computer'  (string)
  info.product = '82801EB/ER (ICH5/ICH5R) LPC Interface Bridge'  (string)
  info.subsystem = 'pci'  (string)
  info.udi = '/org/freedesktop/Hal/devices/pci_8086_24d0'  (string)
  info.vendor = 'Intel Corporation'  (string)
  linux.hotplug_type = 2  (0x2)  (int)
  linux.subsystem = 'pci'  (string)
  linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1f.0'  (string)
  pci.device_class = 6  (0x6)  (int)
  pci.device_protocol = 0  (0x0)  (int)
  pci.device_subclass = 1  (0x1)  (int)
  pci.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1f.0'  (string)
  pci.product = '82801EB/ER (ICH5/ICH5R) LPC Interface Bridge'  (string)
  pci.product_id = 9424  (0x24d0)  (int)
  pci.subsys_product_id = 0  (0x0)  (int)
  pci.subsys_vendor_id = 0  (0x0)  (int)
  pci.vendor = 'Intel Corporation'  (string)
  pci.vendor_id = 32902  (0x8086)  (int)

udi = '/org/freedesktop/Hal/devices/pci_8086_244e'
  info.parent = '/org/freedesktop/Hal/devices/computer'  (string)
  info.product = '82801 PCI Bridge'  (string)
  info.subsystem = 'pci'  (string)
  info.udi = '/org/freedesktop/Hal/devices/pci_8086_244e'  (string)
  info.vendor = 'Intel Corporation'  (string)
  linux.hotplug_type = 2  (0x2)  (int)
  linux.subsystem = 'pci'  (string)
  linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1e.0'  (string)
  pci.device_class = 6  (0x6)  (int)
  pci.device_protocol = 0  (0x0)  (int)
  pci.device_subclass = 4  (0x4)  (int)
  pci.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1e.0'  (string)
  pci.product = '82801 PCI Bridge'  (string)
  pci.product_id = 9294  (0x244e)  (int)
  pci.subsys_product_id = 0  (0x0)  (int)
  pci.subsys_vendor_id = 0  (0x0)  (int)
  pci.vendor = 'Intel Corporation'  (string)
  pci.vendor_id = 32902  (0x8086)  (int)

udi = '/org/freedesktop/Hal/devices/pci_14e4_1696'
  info.linux.driver = 'tg3'  (string)
  info.parent = '/org/freedesktop/Hal/devices/pci_8086_244e'  (string)
  info.product = 'NetXtreme BCM5782 Gigabit Ethernet'  (string)
  info.subsystem = 'pci'  (string)
  info.udi = '/org/freedesktop/Hal/devices/pci_14e4_1696'  (string)
  info.vendor = 'Broadcom Corporation'  (string)
  linux.hotplug_type = 2  (0x2)  (int)
  linux.subsystem = 'pci'  (string)
  linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1e.0/0000:05:02.0'  (string)
  pci.device_class = 2  (0x2)  (int)
  pci.device_protocol = 0  (0x0)  (int)
  pci.device_subclass = 0  (0x0)  (int)
  pci.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1e.0/0000:05:02.0'  (string)
  pci.product = 'NetXtreme BCM5782 Gigabit Ethernet'  (string)
  pci.product_id = 5782  (0x1696)  (int)
  pci.subsys_product = 'd530 CMT (DG746A)'  (string)
  pci.subsys_product_id = 4796  (0x12bc)  (int)
  pci.subsys_vendor = 'Hewlett-Packard Company'  (string)
  pci.subsys_vendor_id = 4156  (0x103c)  (int)
  pci.vendor = 'Broadcom Corporation'  (string)
  pci.vendor_id = 5348  (0x14e4)  (int)

udi = '/org/freedesktop/Hal/devices/net_00_0d_9d_d9_67_be'
  info.capabilities = {'net', 'net.80203', 'wake_on_lan'} (string list)
  info.category = 'net.80203'  (string)
  info.interfaces = {'org.freedesktop.Hal.Device.WakeOnLan'} (string list)
  info.parent = '/org/freedesktop/Hal/devices/pci_14e4_1696'  (string)
  info.product = 'Networking Interface'  (string)
  info.subsystem = 'net'  (string)
  info.udi = '/org/freedesktop/Hal/devices/net_00_0d_9d_d9_67_be'  (string)
  linux.hotplug_type = 2  (0x2)  (int)
  linux.subsystem = 'net'  (string)
  linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1e.0/0000:05:02.0/net/eth0'  (string)
  net.80203.mac_address = 58482845630  (0xd9dd967be)  (uint64)
  net.address = '00:0d:9d:d9:67:be'  (string)
  net.arp_proto_hw_id = 1  (0x1)  (int)
  net.interface = 'eth0'  (string)
  net.linux.ifindex = 2  (0x2)  (int)
  net.originating_device = '/org/freedesktop/Hal/devices/pci_14e4_1696'  (string)
  net.physical_device = '/org/freedesktop/Hal/devices/pci_14e4_1696'  (string)
  org.freedesktop.Hal.Device.WakeOnLan.method_argnames = {'', '', 'enable'} (string list)
  org.freedesktop.Hal.Device.WakeOnLan.method_execpaths = {'hal-system-wol-supported', 'hal-system-wol-enabled', 'hal-system-wol-enable'} (string list)
  org.freedesktop.Hal.Device.WakeOnLan.method_names = {'GetSupported', 'GetEnabled', 'SetEnabled'} (string list)
  org.freedesktop.Hal.Device.WakeOnLan.method_signatures = {'', '', 'b'} (string list)

udi = '/org/freedesktop/Hal/devices/pci_8086_24dd'
  info.linux.driver = 'ehci_hcd'  (string)
  info.parent = '/org/freedesktop/Hal/devices/computer'  (string)
  info.product = '82801EB/ER (ICH5/ICH5R) USB2 EHCI Controller'  (string)
  info.subsystem = 'pci'  (string)
  info.udi = '/org/freedesktop/Hal/devices/pci_8086_24dd'  (string)
  info.vendor = 'Intel Corporation'  (string)
  linux.hotplug_type = 2  (0x2)  (int)
  linux.subsystem = 'pci'  (string)
  linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1d.7'  (string)
  pci.device_class = 12  (0xc)  (int)
  pci.device_protocol = 32  (0x20)  (int)
  pci.device_subclass = 3  (0x3)  (int)
  pci.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1d.7'  (string)
  pci.product = '82801EB/ER (ICH5/ICH5R) USB2 EHCI Controller'  (string)
  pci.product_id = 9437  (0x24dd)  (int)
  pci.subsys_product = 'd530 CMT (DG746A)'  (string)
  pci.subsys_product_id = 4796  (0x12bc)  (int)
  pci.subsys_vendor = 'Hewlett-Packard Company'  (string)
  pci.subsys_vendor_id = 4156  (0x103c)  (int)
  pci.vendor = 'Intel Corporation'  (string)
  pci.vendor_id = 32902  (0x8086)  (int)

udi = '/org/freedesktop/Hal/devices/usb_device_1d6b_2_0000_00_1d_7'
  info.bus = 'usb_device'  (string)
  info.linux.driver = 'usb'  (string)
  info.parent = '/org/freedesktop/Hal/devices/pci_8086_24dd'  (string)
  info.product = '2.0 root hub'  (string)
  info.subsystem = 'usb_device'  (string)
  info.udi = '/org/freedesktop/Hal/devices/usb_device_1d6b_2_0000_00_1d_7'  (string)
  info.vendor = 'Linux Foundation'  (string)
  linux.device_file = '/dev/bus/usb/001/001'  (string)
  linux.hotplug_type = 2  (0x2)  (int)
  linux.subsystem = 'usb'  (string)
  linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1d.7/usb1'  (string)
  usb_device.bus_number = 1  (0x1)  (int)
  usb_device.can_wake_up = true  (bool)
  usb_device.configuration_value = 1  (0x1)  (int)
  usb_device.device_class = 9  (0x9)  (int)
  usb_device.device_protocol = 0  (0x0)  (int)
  usb_device.device_revision_bcd = 518  (0x206)  (int)
  usb_device.device_subclass = 0  (0x0)  (int)
  usb_device.is_self_powered = true  (bool)
  usb_device.linux.device_number = 1  (0x1)  (int)
  usb_device.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1d.7/usb1'  (string)
  usb_device.max_power = 0  (0x0)  (int)
  usb_device.num_configurations = 1  (0x1)  (int)
  usb_device.num_interfaces = 1  (0x1)  (int)
  usb_device.num_ports = 8  (0x8)  (int)
  usb_device.product = '2.0 root hub'  (string)
  usb_device.product_id = 2  (0x2)  (int)
  usb_device.serial = '0000:00:1d.7'  (string)
  usb_device.speed = 480.0 (480) (double)
  usb_device.vendor = 'Linux Foundation'  (string)
  usb_device.vendor_id = 7531  (0x1d6b)  (int)
  usb_device.version = 2.0 (2) (double)

udi = '/org/freedesktop/Hal/devices/usb_device_781_5406_0000184DA8604800'
  info.bus = 'usb_device'  (string)
  info.linux.driver = 'usb'  (string)
  info.parent = '/org/freedesktop/Hal/devices/usb_device_1d6b_2_0000_00_1d_7'  (string)
  info.product = 'Cruzer Micro 1/2/4GB Flash Drive'  (string)
  info.subsystem = 'usb_device'  (string)
  info.udi = '/org/freedesktop/Hal/devices/usb_device_781_5406_0000184DA8604800'  (string)
  info.vendor = 'SanDisk Corp.'  (string)
  linux.device_file = '/dev/bus/usb/001/002'  (string)
  linux.hotplug_type = 2  (0x2)  (int)
  linux.subsystem = 'usb'  (string)
  linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1d.7/usb1/1-5'  (string)
  usb_device.bus_number = 1  (0x1)  (int)
  usb_device.can_wake_up = false  (bool)
  usb_device.configuration_value = 1  (0x1)  (int)
  usb_device.device_class = 0  (0x0)  (int)
  usb_device.device_protocol = 0  (0x0)  (int)
  usb_device.device_revision_bcd = 16  (0x10)  (int)
  usb_device.device_subclass = 0  (0x0)  (int)
  usb_device.is_self_powered = false  (bool)
  usb_device.linux.device_number = 2  (0x2)  (int)
  usb_device.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1d.7/usb1/1-5'  (string)
  usb_device.max_power = 200  (0xc8)  (int)
  usb_device.num_configurations = 1  (0x1)  (int)
  usb_device.num_interfaces = 1  (0x1)  (int)
  usb_device.num_ports = 0  (0x0)  (int)
  usb_device.product = 'Cruzer Micro 1/2/4GB Flash Drive'  (string)
  usb_device.product_id = 21510  (0x5406)  (int)
  usb_device.serial = '0000184DA8604800'  (string)
  usb_device.speed = 480.0 (480) (double)
  usb_device.vendor = 'SanDisk Corp.'  (string)
  usb_device.vendor_id = 1921  (0x781)  (int)
  usb_device.version = 2.0 (2) (double)

udi = '/org/freedesktop/Hal/devices/usb_device_781_5406_0000184DA8604800_if0'
  info.bus = 'usb'  (string)
  info.linux.driver = 'usb-storage'  (string)
  info.parent = '/org/freedesktop/Hal/devices/usb_device_781_5406_0000184DA8604800'  (string)
  info.product = 'USB Mass Storage Interface'  (string)
  info.subsystem = 'usb'  (string)
  info.udi = '/org/freedesktop/Hal/devices/usb_device_781_5406_0000184DA8604800_if0'  (string)
  linux.hotplug_type = 2  (0x2)  (int)
  linux.subsystem = 'usb'  (string)
  linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1d.7/usb1/1-5/1-5:1.0'  (string)
  usb.bus_number = 1  (0x1)  (int)
  usb.can_wake_up = false  (bool)
  usb.configuration_value = 1  (0x1)  (int)
  usb.device_class = 0  (0x0)  (int)
  usb.device_protocol = 0  (0x0)  (int)
  usb.device_revision_bcd = 16  (0x10)  (int)
  usb.device_subclass = 0  (0x0)  (int)
  usb.interface.class = 8  (0x8)  (int)
  usb.interface.number = 0  (0x0)  (int)
  usb.interface.protocol = 80  (0x50)  (int)
  usb.interface.subclass = 6  (0x6)  (int)
  usb.is_self_powered = false  (bool)
  usb.linux.device_number = 2  (0x2)  (int)
  usb.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1d.7/usb1/1-5/1-5:1.0'  (string)
  usb.max_power = 200  (0xc8)  (int)
  usb.num_configurations = 1  (0x1)  (int)
  usb.num_interfaces = 1  (0x1)  (int)
  usb.num_ports = 0  (0x0)  (int)
  usb.product = 'USB Mass Storage Interface'  (string)
  usb.product_id = 21510  (0x5406)  (int)
  usb.serial = '0000184DA8604800'  (string)
  usb.speed = 480.0 (480) (double)
  usb.vendor = 'SanDisk Corp.'  (string)
  usb.vendor_id = 1921  (0x781)  (int)
  usb.version = 2.0 (2) (double)

udi = '/org/freedesktop/Hal/devices/usb_device_781_5406_0000184DA8604800_if0_scsi_host_0'
  info.capabilities = {'scsi_host'} (string list)
  info.category = 'scsi_host'  (string)
  info.parent = '/org/freedesktop/Hal/devices/usb_device_781_5406_0000184DA8604800_if0'  (string)
  info.product = 'SCSI Host Adapter'  (string)
  info.subsystem = 'scsi_host'  (string)
  info.udi = '/org/freedesktop/Hal/devices/usb_device_781_5406_0000184DA8604800_if0_scsi_host_0'  (string)
  linux.hotplug_type = 2  (0x2)  (int)
  linux.subsystem = 'scsi_host'  (string)
  linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1d.7/usb1/1-5/1-5:1.0/host4'  (string)
  scsi_host.host = 4  (0x4)  (int)

udi = '/org/freedesktop/Hal/devices/usb_device_781_5406_0000184DA8604800_if0_scsi_host_0_scsi_device_lun1'
  info.linux.driver = 'sr'  (string)
  info.parent = '/org/freedesktop/Hal/devices/usb_device_781_5406_0000184DA8604800_if0_scsi_host_0'  (string)
  info.product = 'SCSI Device'  (string)
  info.subsystem = 'scsi'  (string)
  info.udi = '/org/freedesktop/Hal/devices/usb_device_781_5406_0000184DA8604800_if0_scsi_host_0_scsi_device_lun1'  (string)
  linux.hotplug_type = 2  (0x2)  (int)
  linux.subsystem = 'scsi'  (string)
  linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1d.7/usb1/1-5/1-5:1.0/host4/target4:0:0/4:0:0:1'  (string)
  scsi.bus = 0  (0x0)  (int)
  scsi.host = 4  (0x4)  (int)
  scsi.lun = 1  (0x1)  (int)
  scsi.model = 'U3 Cruzer Micro'  (string)
  scsi.target = 0  (0x0)  (int)
  scsi.type = 'cdrom'  (string)
  scsi.vendor = 'SanDisk'  (string)

udi = '/org/freedesktop/Hal/devices/temp/117'
  block.device = '/dev/sr1'  (string)
  block.is_volume = false  (bool)
  block.major = 11  (0xb)  (int)
  block.minor = 1  (0x1)  (int)
  info.ignore = true  (bool)
  info.parent = '/org/freedesktop/Hal/devices/usb_device_781_5406_0000184DA8604800_if0_scsi_host_0_scsi_device_lun1'  (string)
  info.product = 'Ignored Device'  (string)
  info.udi = '/org/freedesktop/Hal/devices/ignored-device'  (string)
  info.vendor = 'SanDisk'  (string)
  linux.hotplug_type = 3  (0x3)  (int)
  linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1d.7/usb1/1-5/1-5:1.0/host4/target4:0:0/4:0:0:1/block/sr1'  (string)
  storage.automount_enabled_hint = true  (bool)
  storage.bus = 'usb'  (string)
  storage.drive_type = 'cdrom'  (string)
  storage.firmware_version = '2.18'  (string)
  storage.hotpluggable = true  (bool)
  storage.lun = 1  (0x1)  (int)
  storage.media_check_enabled = true  (bool)
  storage.model = 'U3 Cruzer Micro'  (string)
  storage.no_partitions_hint = true  (bool)
  storage.originating_device = '/org/freedesktop/Hal/devices/usb_device_781_5406_0000184DA8604800_if0'  (string)
  storage.removable = true  (bool)
  storage.removable.media_available = false  (bool)
  storage.removable.support_async_notification = false  (bool)
  storage.requires_eject = true  (bool)
  storage.serial = 'SanDisk_U3_Cruzer_Micro_0000184DA8604800-0:1'  (string)
  storage.size = 0  (0x0)  (uint64)
  storage.vendor = 'SanDisk'  (string)

udi = '/org/freedesktop/Hal/devices/usb_device_781_5406_0000184DA8604800_if0_scsi_host_0_scsi_device_lun1_scsi_generic'
  info.capabilities = {'scsi_generic'} (string list)
  info.category = 'scsi_generic'  (string)
  info.parent = '/org/freedesktop/Hal/devices/usb_device_781_5406_0000184DA8604800_if0_scsi_host_0_scsi_device_lun1'  (string)
  info.product = 'SCSI Generic Interface'  (string)
  info.subsystem = 'scsi_generic'  (string)
  info.udi = '/org/freedesktop/Hal/devices/usb_device_781_5406_0000184DA8604800_if0_scsi_host_0_scsi_device_lun1_scsi_generic'  (string)
  linux.device_file = '/dev/sg4'  (string)
  linux.hotplug_type = 2  (0x2)  (int)
  linux.subsystem = 'scsi_generic'  (string)
  linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1d.7/usb1/1-5/1-5:1.0/host4/target4:0:0/4:0:0:1/scsi_generic/sg4'  (string)
  scsi_generic.device = '/dev/sg4'  (string)

udi = '/org/freedesktop/Hal/devices/usb_device_781_5406_0000184DA8604800_if0_scsi_host_0_scsi_device_lun0'
  info.linux.driver = 'sd'  (string)
  info.parent = '/org/freedesktop/Hal/devices/usb_device_781_5406_0000184DA8604800_if0_scsi_host_0'  (string)
  info.product = 'SCSI Device'  (string)
  info.subsystem = 'scsi'  (string)
  info.udi = '/org/freedesktop/Hal/devices/usb_device_781_5406_0000184DA8604800_if0_scsi_host_0_scsi_device_lun0'  (string)
  linux.hotplug_type = 2  (0x2)  (int)
  linux.subsystem = 'scsi'  (string)
  linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1d.7/usb1/1-5/1-5:1.0/host4/target4:0:0/4:0:0:0'  (string)
  scsi.bus = 0  (0x0)  (int)
  scsi.host = 4  (0x4)  (int)
  scsi.lun = 0  (0x0)  (int)
  scsi.model = 'U3 Cruzer Micro'  (string)
  scsi.target = 0  (0x0)  (int)
  scsi.type = 'disk'  (string)
  scsi.vendor = 'SanDisk'  (string)

udi = '/org/freedesktop/Hal/devices/storage_serial_SanDisk_U3_Cruzer_Micro_0000184DA8604800_0_0'
  block.device = '/dev/sdc'  (string)
  block.is_volume = false  (bool)
  block.major = 8  (0x8)  (int)
  block.minor = 32  (0x20)  (int)
  block.storage_device = '/org/freedesktop/Hal/devices/storage_serial_SanDisk_U3_Cruzer_Micro_0000184DA8604800_0_0'  (string)
  info.addons = {'hald-addon-storage'} (string list)
  info.capabilities = {'storage', 'block'} (string list)
  info.category = 'storage'  (string)
  info.interfaces = {'org.freedesktop.Hal.Device.Storage.Removable'} (string list)
  info.parent = '/org/freedesktop/Hal/devices/usb_device_781_5406_0000184DA8604800_if0_scsi_host_0_scsi_device_lun0'  (string)
  info.product = 'U3 Cruzer Micro'  (string)
  info.udi = '/org/freedesktop/Hal/devices/storage_serial_SanDisk_U3_Cruzer_Micro_0000184DA8604800_0_0'  (string)
  info.vendor = 'SanDisk'  (string)
  linux.hotplug_type = 3  (0x3)  (int)
  linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1d.7/usb1/1-5/1-5:1.0/host4/target4:0:0/4:0:0:0/block/sdc'  (string)
  storage.automount_enabled_hint = true  (bool)
  storage.bus = 'usb'  (string)
  storage.drive_type = 'disk'  (string)
  storage.firmware_version = '2.18'  (string)
  storage.hotpluggable = true  (bool)
  storage.lun = 0  (0x0)  (int)
  storage.media_check_enabled = true  (bool)
  storage.model = 'U3 Cruzer Micro'  (string)
  storage.no_partitions_hint = false  (bool)
  storage.originating_device = '/org/freedesktop/Hal/devices/usb_device_781_5406_0000184DA8604800_if0'  (string)
  storage.partitioning_scheme = 'mbr'  (string)
  storage.removable = true  (bool)
  storage.removable.media_available = true  (bool)
  storage.removable.media_size = 4103938560  (0xf49d2200)  (uint64)
  storage.removable.support_async_notification = false  (bool)
  storage.requires_eject = false  (bool)
  storage.serial = 'SanDisk_U3_Cruzer_Micro_0000184DA8604800-0:0'  (string)
  storage.size = 0  (0x0)  (uint64)
  storage.vendor = 'SanDisk'  (string)

udi = '/org/freedesktop/Hal/devices/volume_part1_size_4095640576'
  block.device = '/dev/sdc1'  (string)
  block.is_volume = true  (bool)
  block.major = 8  (0x8)  (int)
  block.minor = 33  (0x21)  (int)
  block.storage_device = '/org/freedesktop/Hal/devices/storage_serial_SanDisk_U3_Cruzer_Micro_0000184DA8604800_0_0'  (string)
  info.capabilities = {'volume', 'block'} (string list)
  info.category = 'volume'  (string)
  info.interfaces = {'org.freedesktop.Hal.Device.Volume'} (string list)
  info.parent = '/org/freedesktop/Hal/devices/storage_serial_SanDisk_U3_Cruzer_Micro_0000184DA8604800_0_0'  (string)
  info.product = 'Volume (vfat)'  (string)
  info.udi = '/org/freedesktop/Hal/devices/volume_part1_size_4095640576'  (string)
  linux.hotplug_type = 3  (0x3)  (int)
  linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1d.7/usb1/1-5/1-5:1.0/host4/target4:0:0/4:0:0:0/block/sdc/sdc1'  (string)
  org.freedesktop.Hal.Device.Volume.method_argnames = {'mount_point fstype extra_options', 'extra_options', 'extra_options'} (string list)
  org.freedesktop.Hal.Device.Volume.method_execpaths = {'hal-storage-mount', 'hal-storage-unmount', 'hal-storage-eject'} (string list)
  org.freedesktop.Hal.Device.Volume.method_names = {'Mount', 'Unmount', 'Eject'} (string list)
  org.freedesktop.Hal.Device.Volume.method_signatures = {'ssas', 'as', 'as'} (string list)
  volume.block_size = 512  (0x200)  (int)
  volume.fstype = 'vfat'  (string)
  volume.fsusage = 'filesystem'  (string)
  volume.fsversion = 'FAT32'  (string)
  volume.ignore = false  (bool)
  volume.is_disc = false  (bool)
  volume.is_mounted = true  (bool)
  volume.is_mounted_read_only = false  (bool)
  volume.is_partition = true  (bool)
  volume.label = ''  (string)
  volume.linux.is_device_mapper = false  (bool)
  volume.mount.valid_options = {'ro', 'sync', 'dirsync', 'noatime', 'nodiratime', 'noexec', 'quiet', 'remount', 'exec', 'utf8', 'shortname=', 'codepage=', 'iocharset=', 'umask=', 'dmask=', 'fmask=', 'uid=', 'flush'} (string list)
  volume.mount_point = '/mnt/foo'  (string)
  volume.num_blocks = 7999298  (0x7a0f42)  (uint64)
  volume.partition.media_size = 4103938560  (0xf49d2200)  (uint64)
  volume.partition.number = 1  (0x1)  (int)
  volume.partition.start = 97280  (0x17c00)  (uint64)
  volume.size = 4095640576  (0xf41e8400)  (uint64)
  volume.unmount.valid_options = {'lazy'} (string list)
  volume.uuid = ''  (string)

udi = '/org/freedesktop/Hal/devices/usb_device_781_5406_0000184DA8604800_if0_scsi_host_0_scsi_device_lun0_scsi_generic'
  info.capabilities = {'scsi_generic'} (string list)
  info.category = 'scsi_generic'  (string)
  info.parent = '/org/freedesktop/Hal/devices/usb_device_781_5406_0000184DA8604800_if0_scsi_host_0_scsi_device_lun0'  (string)
  info.product = 'SCSI Generic Interface'  (string)
  info.subsystem = 'scsi_generic'  (string)
  info.udi = '/org/freedesktop/Hal/devices/usb_device_781_5406_0000184DA8604800_if0_scsi_host_0_scsi_device_lun0_scsi_generic'  (string)
  linux.device_file = '/dev/sg3'  (string)
  linux.hotplug_type = 2  (0x2)  (int)
  linux.subsystem = 'scsi_generic'  (string)
  linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1d.7/usb1/1-5/1-5:1.0/host4/target4:0:0/4:0:0:0/scsi_generic/sg3'  (string)
  scsi_generic.device = '/dev/sg3'  (string)

udi = '/org/freedesktop/Hal/devices/usb_device_781_5406_0000184DA8604800_if0_scsi_host'
  info.capabilities = {'scsi_host'} (string list)
  info.category = 'scsi_host'  (string)
  info.parent = '/org/freedesktop/Hal/devices/usb_device_781_5406_0000184DA8604800_if0'  (string)
  info.product = 'SCSI Host Adapter'  (string)
  info.subsystem = 'scsi_host'  (string)
  info.udi = '/org/freedesktop/Hal/devices/usb_device_781_5406_0000184DA8604800_if0_scsi_host'  (string)
  linux.hotplug_type = 2  (0x2)  (int)
  linux.subsystem = 'scsi_host'  (string)
  linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1d.7/usb1/1-5/1-5:1.0/host4/scsi_host/host4'  (string)
  scsi_host.host = 4  (0x4)  (int)

udi = '/org/freedesktop/Hal/devices/usb_device_1d6b_2_0000_00_1d_7_if0'
  info.bus = 'usb'  (string)
  info.linux.driver = 'hub'  (string)
  info.parent = '/org/freedesktop/Hal/devices/usb_device_1d6b_2_0000_00_1d_7'  (string)
  info.product = 'USB Hub Interface'  (string)
  info.subsystem = 'usb'  (string)
  info.udi = '/org/freedesktop/Hal/devices/usb_device_1d6b_2_0000_00_1d_7_if0'  (string)
  linux.hotplug_type = 2  (0x2)  (int)
  linux.subsystem = 'usb'  (string)
  linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1d.7/usb1/1-0:1.0'  (string)
  usb.bus_number = 1  (0x1)  (int)
  usb.can_wake_up = true  (bool)
  usb.configuration_value = 1  (0x1)  (int)
  usb.device_class = 9  (0x9)  (int)
  usb.device_protocol = 0  (0x0)  (int)
  usb.device_revision_bcd = 518  (0x206)  (int)
  usb.device_subclass = 0  (0x0)  (int)
  usb.interface.class = 9  (0x9)  (int)
  usb.interface.number = 0  (0x0)  (int)
  usb.interface.protocol = 0  (0x0)  (int)
  usb.interface.subclass = 0  (0x0)  (int)
  usb.is_self_powered = true  (bool)
  usb.linux.device_number = 1  (0x1)  (int)
  usb.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1d.7/usb1/1-0:1.0'  (string)
  usb.max_power = 0  (0x0)  (int)
  usb.num_configurations = 1  (0x1)  (int)
  usb.num_interfaces = 1  (0x1)  (int)
  usb.num_ports = 8  (0x8)  (int)
  usb.product = 'USB Hub Interface'  (string)
  usb.product_id = 2  (0x2)  (int)
  usb.serial = '0000:00:1d.7'  (string)
  usb.speed = 480.0 (480) (double)
  usb.vendor = 'Linux Foundation'  (string)
  usb.vendor_id = 7531  (0x1d6b)  (int)
  usb.version = 2.0 (2) (double)

udi = '/org/freedesktop/Hal/devices/pci_8086_24d7'
  info.linux.driver = 'uhci_hcd'  (string)
  info.parent = '/org/freedesktop/Hal/devices/computer'  (string)
  info.product = '82801EB/ER (ICH5/ICH5R) USB UHCI Controller #3'  (string)
  info.subsystem = 'pci'  (string)
  info.udi = '/org/freedesktop/Hal/devices/pci_8086_24d7'  (string)
  info.vendor = 'Intel Corporation'  (string)
  linux.hotplug_type = 2  (0x2)  (int)
  linux.subsystem = 'pci'  (string)
  linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1d.2'  (string)
  pci.device_class = 12  (0xc)  (int)
  pci.device_protocol = 0  (0x0)  (int)
  pci.device_subclass = 3  (0x3)  (int)
  pci.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1d.2'  (string)
  pci.product = '82801EB/ER (ICH5/ICH5R) USB UHCI Controller #3'  (string)
  pci.product_id = 9431  (0x24d7)  (int)
  pci.subsys_product = 'd530 CMT (DG746A)'  (string)
  pci.subsys_product_id = 4796  (0x12bc)  (int)
  pci.subsys_vendor = 'Hewlett-Packard Company'  (string)
  pci.subsys_vendor_id = 4156  (0x103c)  (int)
  pci.vendor = 'Intel Corporation'  (string)
  pci.vendor_id = 32902  (0x8086)  (int)

udi = '/org/freedesktop/Hal/devices/usb_device_1d6b_1_0000_00_1d_2'
  info.bus = 'usb_device'  (string)
  info.linux.driver = 'usb'  (string)
  info.parent = '/org/freedesktop/Hal/devices/pci_8086_24d7'  (string)
  info.product = '1.1 root hub'  (string)
  info.subsystem = 'usb_device'  (string)
  info.udi = '/org/freedesktop/Hal/devices/usb_device_1d6b_1_0000_00_1d_2'  (string)
  info.vendor = 'Linux Foundation'  (string)
  linux.device_file = '/dev/bus/usb/004/001'  (string)
  linux.hotplug_type = 2  (0x2)  (int)
  linux.subsystem = 'usb'  (string)
  linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1d.2/usb4'  (string)
  usb_device.bus_number = 4  (0x4)  (int)
  usb_device.can_wake_up = true  (bool)
  usb_device.configuration_value = 1  (0x1)  (int)
  usb_device.device_class = 9  (0x9)  (int)
  usb_device.device_protocol = 0  (0x0)  (int)
  usb_device.device_revision_bcd = 518  (0x206)  (int)
  usb_device.device_subclass = 0  (0x0)  (int)
  usb_device.is_self_powered = true  (bool)
  usb_device.linux.device_number = 1  (0x1)  (int)
  usb_device.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1d.2/usb4'  (string)
  usb_device.max_power = 0  (0x0)  (int)
  usb_device.num_configurations = 1  (0x1)  (int)
  usb_device.num_interfaces = 1  (0x1)  (int)
  usb_device.num_ports = 2  (0x2)  (int)
  usb_device.product = '1.1 root hub'  (string)
  usb_device.product_id = 1  (0x1)  (int)
  usb_device.serial = '0000:00:1d.2'  (string)
  usb_device.speed = 12.0 (12) (double)
  usb_device.vendor = 'Linux Foundation'  (string)
  usb_device.vendor_id = 7531  (0x1d6b)  (int)
  usb_device.version = 1.1 (1.1) (double)

udi = '/org/freedesktop/Hal/devices/usb_device_1d6b_1_0000_00_1d_2_if0'
  info.bus = 'usb'  (string)
  info.linux.driver = 'hub'  (string)
  info.parent = '/org/freedesktop/Hal/devices/usb_device_1d6b_1_0000_00_1d_2'  (string)
  info.product = 'USB Hub Interface'  (string)
  info.subsystem = 'usb'  (string)
  info.udi = '/org/freedesktop/Hal/devices/usb_device_1d6b_1_0000_00_1d_2_if0'  (string)
  linux.hotplug_type = 2  (0x2)  (int)
  linux.subsystem = 'usb'  (string)
  linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1d.2/usb4/4-0:1.0'  (string)
  usb.bus_number = 4  (0x4)  (int)
  usb.can_wake_up = true  (bool)
  usb.configuration_value = 1  (0x1)  (int)
  usb.device_class = 9  (0x9)  (int)
  usb.device_protocol = 0  (0x0)  (int)
  usb.device_revision_bcd = 518  (0x206)  (int)
  usb.device_subclass = 0  (0x0)  (int)
  usb.interface.class = 9  (0x9)  (int)
  usb.interface.number = 0  (0x0)  (int)
  usb.interface.protocol = 0  (0x0)  (int)
  usb.interface.subclass = 0  (0x0)  (int)
  usb.is_self_powered = true  (bool)
  usb.linux.device_number = 1  (0x1)  (int)
  usb.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1d.2/usb4/4-0:1.0'  (string)
  usb.max_power = 0  (0x0)  (int)
  usb.num_configurations = 1  (0x1)  (int)
  usb.num_interfaces = 1  (0x1)  (int)
  usb.num_ports = 2  (0x2)  (int)
  usb.product = 'USB Hub Interface'  (string)
  usb.product_id = 1  (0x1)  (int)
  usb.serial = '0000:00:1d.2'  (string)
  usb.speed = 12.0 (12) (double)
  usb.vendor = 'Linux Foundation'  (string)
  usb.vendor_id = 7531  (0x1d6b)  (int)
  usb.version = 1.1 (1.1) (double)

udi = '/org/freedesktop/Hal/devices/pci_8086_24d4'
  info.linux.driver = 'uhci_hcd'  (string)
  info.parent = '/org/freedesktop/Hal/devices/computer'  (string)
  info.product = '82801EB/ER (ICH5/ICH5R) USB UHCI Controller #2'  (string)
  info.subsystem = 'pci'  (string)
  info.udi = '/org/freedesktop/Hal/devices/pci_8086_24d4'  (string)
  info.vendor = 'Intel Corporation'  (string)
  linux.hotplug_type = 2  (0x2)  (int)
  linux.subsystem = 'pci'  (string)
  linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1d.1'  (string)
  pci.device_class = 12  (0xc)  (int)
  pci.device_protocol = 0  (0x0)  (int)
  pci.device_subclass = 3  (0x3)  (int)
  pci.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1d.1'  (string)
  pci.product = '82801EB/ER (ICH5/ICH5R) USB UHCI Controller #2'  (string)
  pci.product_id = 9428  (0x24d4)  (int)
  pci.subsys_product = 'd530 CMT (DG746A)'  (string)
  pci.subsys_product_id = 4796  (0x12bc)  (int)
  pci.subsys_vendor = 'Hewlett-Packard Company'  (string)
  pci.subsys_vendor_id = 4156  (0x103c)  (int)
  pci.vendor = 'Intel Corporation'  (string)
  pci.vendor_id = 32902  (0x8086)  (int)

udi = '/org/freedesktop/Hal/devices/usb_device_1d6b_1_0000_00_1d_1'
  info.bus = 'usb_device'  (string)
  info.linux.driver = 'usb'  (string)
  info.parent = '/org/freedesktop/Hal/devices/pci_8086_24d4'  (string)
  info.product = '1.1 root hub'  (string)
  info.subsystem = 'usb_device'  (string)
  info.udi = '/org/freedesktop/Hal/devices/usb_device_1d6b_1_0000_00_1d_1'  (string)
  info.vendor = 'Linux Foundation'  (string)
  linux.device_file = '/dev/bus/usb/003/001'  (string)
  linux.hotplug_type = 2  (0x2)  (int)
  linux.subsystem = 'usb'  (string)
  linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1d.1/usb3'  (string)
  usb_device.bus_number = 3  (0x3)  (int)
  usb_device.can_wake_up = true  (bool)
  usb_device.configuration_value = 1  (0x1)  (int)
  usb_device.device_class = 9  (0x9)  (int)
  usb_device.device_protocol = 0  (0x0)  (int)
  usb_device.device_revision_bcd = 518  (0x206)  (int)
  usb_device.device_subclass = 0  (0x0)  (int)
  usb_device.is_self_powered = true  (bool)
  usb_device.linux.device_number = 1  (0x1)  (int)
  usb_device.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1d.1/usb3'  (string)
  usb_device.max_power = 0  (0x0)  (int)
  usb_device.num_configurations = 1  (0x1)  (int)
  usb_device.num_interfaces = 1  (0x1)  (int)
  usb_device.num_ports = 2  (0x2)  (int)
  usb_device.product = '1.1 root hub'  (string)
  usb_device.product_id = 1  (0x1)  (int)
  usb_device.serial = '0000:00:1d.1'  (string)
  usb_device.speed = 12.0 (12) (double)
  usb_device.vendor = 'Linux Foundation'  (string)
  usb_device.vendor_id = 7531  (0x1d6b)  (int)
  usb_device.version = 1.1 (1.1) (double)

udi = '/org/freedesktop/Hal/devices/usb_device_1d6b_1_0000_00_1d_1_if0'
  info.bus = 'usb'  (string)
  info.linux.driver = 'hub'  (string)
  info.parent = '/org/freedesktop/Hal/devices/usb_device_1d6b_1_0000_00_1d_1'  (string)
  info.product = 'USB Hub Interface'  (string)
  info.subsystem = 'usb'  (string)
  info.udi = '/org/freedesktop/Hal/devices/usb_device_1d6b_1_0000_00_1d_1_if0'  (string)
  linux.hotplug_type = 2  (0x2)  (int)
  linux.subsystem = 'usb'  (string)
  linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1d.1/usb3/3-0:1.0'  (string)
  usb.bus_number = 3  (0x3)  (int)
  usb.can_wake_up = true  (bool)
  usb.configuration_value = 1  (0x1)  (int)
  usb.device_class = 9  (0x9)  (int)
  usb.device_protocol = 0  (0x0)  (int)
  usb.device_revision_bcd = 518  (0x206)  (int)
  usb.device_subclass = 0  (0x0)  (int)
  usb.interface.class = 9  (0x9)  (int)
  usb.interface.number = 0  (0x0)  (int)
  usb.interface.protocol = 0  (0x0)  (int)
  usb.interface.subclass = 0  (0x0)  (int)
  usb.is_self_powered = true  (bool)
  usb.linux.device_number = 1  (0x1)  (int)
  usb.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1d.1/usb3/3-0:1.0'  (string)
  usb.max_power = 0  (0x0)  (int)
  usb.num_configurations = 1  (0x1)  (int)
  usb.num_interfaces = 1  (0x1)  (int)
  usb.num_ports = 2  (0x2)  (int)
  usb.product = 'USB Hub Interface'  (string)
  usb.product_id = 1  (0x1)  (int)
  usb.serial = '0000:00:1d.1'  (string)
  usb.speed = 12.0 (12) (double)
  usb.vendor = 'Linux Foundation'  (string)
  usb.vendor_id = 7531  (0x1d6b)  (int)
  usb.version = 1.1 (1.1) (double)

udi = '/org/freedesktop/Hal/devices/pci_8086_24d2'
  info.linux.driver = 'uhci_hcd'  (string)
  info.parent = '/org/freedesktop/Hal/devices/computer'  (string)
  info.product = '82801EB/ER (ICH5/ICH5R) USB UHCI Controller #1'  (string)
  info.subsystem = 'pci'  (string)
  info.udi = '/org/freedesktop/Hal/devices/pci_8086_24d2'  (string)
  info.vendor = 'Intel Corporation'  (string)
  linux.hotplug_type = 2  (0x2)  (int)
  linux.subsystem = 'pci'  (string)
  linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1d.0'  (string)
  pci.device_class = 12  (0xc)  (int)
  pci.device_protocol = 0  (0x0)  (int)
  pci.device_subclass = 3  (0x3)  (int)
  pci.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1d.0'  (string)
  pci.product = '82801EB/ER (ICH5/ICH5R) USB UHCI Controller #1'  (string)
  pci.product_id = 9426  (0x24d2)  (int)
  pci.subsys_product = 'd530 CMT (DG746A)'  (string)
  pci.subsys_product_id = 4796  (0x12bc)  (int)
  pci.subsys_vendor = 'Hewlett-Packard Company'  (string)
  pci.subsys_vendor_id = 4156  (0x103c)  (int)
  pci.vendor = 'Intel Corporation'  (string)
  pci.vendor_id = 32902  (0x8086)  (int)

udi = '/org/freedesktop/Hal/devices/usb_device_1d6b_1_0000_00_1d_0'
  info.bus = 'usb_device'  (string)
  info.linux.driver = 'usb'  (string)
  info.parent = '/org/freedesktop/Hal/devices/pci_8086_24d2'  (string)
  info.product = '1.1 root hub'  (string)
  info.subsystem = 'usb_device'  (string)
  info.udi = '/org/freedesktop/Hal/devices/usb_device_1d6b_1_0000_00_1d_0'  (string)
  info.vendor = 'Linux Foundation'  (string)
  linux.device_file = '/dev/bus/usb/002/001'  (string)
  linux.hotplug_type = 2  (0x2)  (int)
  linux.subsystem = 'usb'  (string)
  linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1d.0/usb2'  (string)
  usb_device.bus_number = 2  (0x2)  (int)
  usb_device.can_wake_up = true  (bool)
  usb_device.configuration_value = 1  (0x1)  (int)
  usb_device.device_class = 9  (0x9)  (int)
  usb_device.device_protocol = 0  (0x0)  (int)
  usb_device.device_revision_bcd = 518  (0x206)  (int)
  usb_device.device_subclass = 0  (0x0)  (int)
  usb_device.is_self_powered = true  (bool)
  usb_device.linux.device_number = 1  (0x1)  (int)
  usb_device.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1d.0/usb2'  (string)
  usb_device.max_power = 0  (0x0)  (int)
  usb_device.num_configurations = 1  (0x1)  (int)
  usb_device.num_interfaces = 1  (0x1)  (int)
  usb_device.num_ports = 2  (0x2)  (int)
  usb_device.product = '1.1 root hub'  (string)
  usb_device.product_id = 1  (0x1)  (int)
  usb_device.serial = '0000:00:1d.0'  (string)
  usb_device.speed = 12.0 (12) (double)
  usb_device.vendor = 'Linux Foundation'  (string)
  usb_device.vendor_id = 7531  (0x1d6b)  (int)
  usb_device.version = 1.1 (1.1) (double)

udi = '/org/freedesktop/Hal/devices/usb_device_1d6b_1_0000_00_1d_0_if0'
  info.bus = 'usb'  (string)
  info.linux.driver = 'hub'  (string)
  info.parent = '/org/freedesktop/Hal/devices/usb_device_1d6b_1_0000_00_1d_0'  (string)
  info.product = 'USB Hub Interface'  (string)
  info.subsystem = 'usb'  (string)
  info.udi = '/org/freedesktop/Hal/devices/usb_device_1d6b_1_0000_00_1d_0_if0'  (string)
  linux.hotplug_type = 2  (0x2)  (int)
  linux.subsystem = 'usb'  (string)
  linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1d.0/usb2/2-0:1.0'  (string)
  usb.bus_number = 2  (0x2)  (int)
  usb.can_wake_up = true  (bool)
  usb.configuration_value = 1  (0x1)  (int)
  usb.device_class = 9  (0x9)  (int)
  usb.device_protocol = 0  (0x0)  (int)
  usb.device_revision_bcd = 518  (0x206)  (int)
  usb.device_subclass = 0  (0x0)  (int)
  usb.interface.class = 9  (0x9)  (int)
  usb.interface.number = 0  (0x0)  (int)
  usb.interface.protocol = 0  (0x0)  (int)
  usb.interface.subclass = 0  (0x0)  (int)
  usb.is_self_powered = true  (bool)
  usb.linux.device_number = 1  (0x1)  (int)
  usb.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:1d.0/usb2/2-0:1.0'  (string)
  usb.max_power = 0  (0x0)  (int)
  usb.num_configurations = 1  (0x1)  (int)
  usb.num_interfaces = 1  (0x1)  (int)
  usb.num_ports = 2  (0x2)  (int)
  usb.product = 'USB Hub Interface'  (string)
  usb.product_id = 1  (0x1)  (int)
  usb.serial = '0000:00:1d.0'  (string)
  usb.speed = 12.0 (12) (double)
  usb.vendor = 'Linux Foundation'  (string)
  usb.vendor_id = 7531  (0x1d6b)  (int)
  usb.version = 1.1 (1.1) (double)

udi = '/org/freedesktop/Hal/devices/pci_8086_2576'
  info.parent = '/org/freedesktop/Hal/devices/computer'  (string)
  info.product = '82865G/PE/P Processor to I/O Memory Interface'  (string)
  info.subsystem = 'pci'  (string)
  info.udi = '/org/freedesktop/Hal/devices/pci_8086_2576'  (string)
  info.vendor = 'Intel Corporation'  (string)
  linux.hotplug_type = 2  (0x2)  (int)
  linux.subsystem = 'pci'  (string)
  linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:06.0'  (string)
  pci.device_class = 8  (0x8)  (int)
  pci.device_protocol = 0  (0x0)  (int)
  pci.device_subclass = 128  (0x80)  (int)
  pci.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:06.0'  (string)
  pci.product = '82865G/PE/P Processor to I/O Memory Interface'  (string)
  pci.product_id = 9590  (0x2576)  (int)
  pci.subsys_product_id = 0  (0x0)  (int)
  pci.subsys_vendor_id = 0  (0x0)  (int)
  pci.vendor = 'Intel Corporation'  (string)
  pci.vendor_id = 32902  (0x8086)  (int)

udi = '/org/freedesktop/Hal/devices/pci_8086_2572'
  info.linux.driver = 'i915'  (string)
  info.parent = '/org/freedesktop/Hal/devices/computer'  (string)
  info.product = '82865G Integrated Graphics Controller'  (string)
  info.subsystem = 'pci'  (string)
  info.udi = '/org/freedesktop/Hal/devices/pci_8086_2572'  (string)
  info.vendor = 'Intel Corporation'  (string)
  linux.hotplug_type = 2  (0x2)  (int)
  linux.subsystem = 'pci'  (string)
  linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:02.0'  (string)
  pci.device_class = 3  (0x3)  (int)
  pci.device_protocol = 0  (0x0)  (int)
  pci.device_subclass = 0  (0x0)  (int)
  pci.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:02.0'  (string)
  pci.product = '82865G Integrated Graphics Controller'  (string)
  pci.product_id = 9586  (0x2572)  (int)
  pci.subsys_product = 'D530 sff(dc578av)'  (string)
  pci.subsys_product_id = 4796  (0x12bc)  (int)
  pci.subsys_vendor = 'Hewlett-Packard Company'  (string)
  pci.subsys_vendor_id = 4156  (0x103c)  (int)
  pci.vendor = 'Intel Corporation'  (string)
  pci.vendor_id = 32902  (0x8086)  (int)

udi = '/org/freedesktop/Hal/devices/pci_8086_2572_drm__null__controlD64'
  info.capabilities = {'drm'} (string list)
  info.category = 'drm'  (string)
  info.parent = '/org/freedesktop/Hal/devices/pci_8086_2572'  (string)
  info.product = 'Direct Rendering Manager Device'  (string)
  info.subsystem = 'drm'  (string)
  info.udi = '/org/freedesktop/Hal/devices/pci_8086_2572_drm__null__controlD64'  (string)
  info.vendor = 'Intel Corporation'  (string)
  linux.device_file = '/dev/dri/controlD64'  (string)
  linux.hotplug_type = 2  (0x2)  (int)
  linux.subsystem = 'drm'  (string)
  linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:02.0/drm/controlD64'  (string)

udi = '/org/freedesktop/Hal/devices/pci_8086_2572_drm__null__card0'
  info.capabilities = {'drm'} (string list)
  info.category = 'drm'  (string)
  info.parent = '/org/freedesktop/Hal/devices/pci_8086_2572'  (string)
  info.product = 'Direct Rendering Manager Device'  (string)
  info.subsystem = 'drm'  (string)
  info.udi = '/org/freedesktop/Hal/devices/pci_8086_2572_drm__null__card0'  (string)
  info.vendor = 'Intel Corporation'  (string)
  linux.device_file = '/dev/dri/card0'  (string)
  linux.hotplug_type = 2  (0x2)  (int)
  linux.subsystem = 'drm'  (string)
  linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:02.0/drm/card0'  (string)

udi = '/org/freedesktop/Hal/devices/pci_8086_2572_drm__null__card0_drm__null__card0_VGA_1'
  info.capabilities = {'drm'} (string list)
  info.category = 'drm'  (string)
  info.parent = '/org/freedesktop/Hal/devices/pci_8086_2572_drm__null__card0'  (string)
  info.product = 'Direct Rendering Manager Device'  (string)
  info.subsystem = 'drm'  (string)
  info.udi = '/org/freedesktop/Hal/devices/pci_8086_2572_drm__null__card0_drm__null__card0_VGA_1'  (string)
  info.vendor = 'Intel Corporation'  (string)
  linux.device_file = ''  (string)
  linux.hotplug_type = 2  (0x2)  (int)
  linux.subsystem = 'drm'  (string)
  linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:02.0/drm/card0/card0-VGA-1'  (string)

udi = '/org/freedesktop/Hal/devices/pci_8086_2570'
  info.linux.driver = 'agpgart-intel'  (string)
  info.parent = '/org/freedesktop/Hal/devices/computer'  (string)
  info.product = '82865G/PE/P DRAM Controller/Host-Hub Interface'  (string)
  info.subsystem = 'pci'  (string)
  info.udi = '/org/freedesktop/Hal/devices/pci_8086_2570'  (string)
  info.vendor = 'Intel Corporation'  (string)
  linux.hotplug_type = 2  (0x2)  (int)
  linux.subsystem = 'pci'  (string)
  linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:00.0'  (string)
  pci.device_class = 6  (0x6)  (int)
  pci.device_protocol = 0  (0x0)  (int)
  pci.device_subclass = 0  (0x0)  (int)
  pci.linux.sysfs_path = '/sys/devices/pci0000:00/0000:00:00.0'  (string)
  pci.product = '82865G/PE/P DRAM Controller/Host-Hub Interface'  (string)
  pci.product_id = 9584  (0x2570)  (int)
  pci.subsys_product = 'd330 uT'  (string)
  pci.subsys_product_id = 4796  (0x12bc)  (int)
  pci.subsys_vendor = 'Hewlett-Packard Company'  (string)
  pci.subsys_vendor_id = 4156  (0x103c)  (int)
  pci.vendor = 'Intel Corporation'  (string)
  pci.vendor_id = 32902  (0x8086)  (int)


Dumped 85 device(s) from the Global Device List.
------------------------------------------------

dmesg is as follows
Initializing cgroup subsys cpuset
Initializing cgroup subsys cpu
Linux version 2.6.31.5-122.fc12.i686 (mockbuild@xxxxxxxxxxxxxxxxxxxxxxxxxxx) (gcc version 4.4.2 20091027 (Red Hat 4.4.2-7) (GCC) ) #1 SMP Thu Nov 5 02:08:26 EST 2009
KERNEL supported cpus:
  Intel GenuineIntel
  AMD AuthenticAMD
  NSC Geode by NSC
  Cyrix CyrixInstead
  Centaur CentaurHauls
  Transmeta GenuineTMx86
  Transmeta TransmetaCPU
  UMC UMC UMC UMC
BIOS-provided physical RAM map:
 BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
 BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
 BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
 BIOS-e820: 0000000000100000 - 000000006f7f0000 (usable)
 BIOS-e820: 000000006f7f0000 - 0000000070000000 (reserved)
 BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved)
DMI 2.3 present.
last_pfn = 0x6f7f0 max_arch_pfn = 0x100000
MTRR default type: uncachable
MTRR fixed ranges enabled:
  00000-9FFFF write-back
  A0000-BFFFF uncachable
  C0000-DFFFF write-protect
  E0000-EFFFF write-back
  F0000-FFFFF write-protect
MTRR variable ranges enabled:
  0 base 000000000 mask FC0000000 write-back
  1 base 040000000 mask FE0000000 write-back
  2 base 060000000 mask FF0000000 write-back
  3 base 06F800000 mask FFF800000 uncachable
  4 base 0FEDA0000 mask FFFFE0000 write-back
  5 disabled
  6 disabled
  7 disabled
x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
original variable MTRRs
reg 0, base: 0GB, range: 1GB, type WB
reg 1, base: 1GB, range: 512MB, type WB
reg 2, base: 1536MB, range: 256MB, type WB
reg 3, base: 1784MB, range: 8MB, type UC
reg 4, base: 4175488KB, range: 128KB, type WB
total RAM coverred: 1784M
Found optimal setting for mtrr clean up
 gran_size: 64K 	chunk_size: 512M 	num_reg: 4  	lose cover RAM: 0G
New variable MTRRs
reg 0, base: 0GB, range: 2GB, type WB
reg 1, base: 1784MB, range: 8MB, type UC
reg 2, base: 1792MB, range: 256MB, type UC
reg 3, base: 4175488KB, range: 128KB, type WB
x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
e820 update range: 000000006f800000 - 00000000feda0000 (usable) ==> (reserved)
initial memory mapped : 0 - 01000000
init_memory_mapping: 0000000000000000-00000000373fe000
Using x86 segment limits to approximate NX protection
 0000000000 - 0000400000 page 4k
 0000400000 - 0037000000 page 2M
 0037000000 - 00373fe000 page 4k
kernel direct mapping tables up to 373fe000 @ 7000-d000
RAMDISK: 6e211000 - 6f7ce623
Allocated new RAMDISK: 00ac8000 - 02085623
Move RAMDISK from 000000006e211000 - 000000006f7ce622 to 00ac8000 - 02085622
ACPI: RSDP 000e9e10 00014 (v00 COMPAQ)
ACPI: RSDT 000e5640 00084 (v01 COMPAQ CPQ0064  20080807      00000000)
ACPI: FACP 000e56f8 00074 (v01 COMPAQ SPRINGD  00000001      00000000)
ACPI: DSDT 000e5808 00D7D (v01 COMPAQ     DSDT 00000001 MSFT 0100000E)
ACPI: FACS 000e5600 00040
ACPI: SSDT 000e6585 00685 (v01 COMPAQ  PROJECT 00000001 MSFT 0100000E)
ACPI: SSDT 000e6c0a 0054C (v01 COMPAQ CORE_PNP 00000001 MSFT 0100000E)
ACPI: SSDT 000e7156 001F2 (v01 COMPAQ CORE_UTL 00000001 MSFT 0100000E)
ACPI: SSDT 000e7348 0032E (v01 COMPAQ VILLTBL1 00000001 MSFT 0100000E)
ACPI: SSDT 000e7676 0053F (v01 COMPAQ LGCYLITE 00000001 MSFT 0100000E)
ACPI: SSDT 000e7bb5 00167 (v01 COMPAQ    UART2 00000001 MSFT 0100000E)
ACPI: SSDT 000e7d1c 0014E (v01 COMPAQ   FLOPPY 00000001 MSFT 0100000E)
ACPI: APIC 000e576c 00068 (v01 COMPAQ SPRINGD  00000001      00000000)
ACPI: SSDT 000e9b2c 000B2 (v01 COMPAQ     APIC 00000001 MSFT 0100000E)
ACPI: ASF! 000e57d4 00034 (v16 COMPAQ SPRINGD  00000001      00000000)
ACPI: SSDT 000e82d8 0040F (v01 COMPAQ PNP_PRSS 00000001 MSFT 0100000E)
ACPI: SSDT 000e86e7 0016D (v01 COMPAQ UR2_PRSS 00000001 MSFT 0100000E)
ACPI: SSDT 000e8854 00119 (v01 COMPAQ FPY_PRSS 00000001 MSFT 0100000E)
ACPI: SSDT 000e8a22 00167 (v01 COMPAQ       S3 00000001 MSFT 0100000E)
ACPI: SSDT 000e8b89 000DD (v01 COMPAQ  CORE_S3 00000001 MSFT 0100000E)
ACPI: SSDT 000e8c66 00144 (v01 COMPAQ   PIDETM 00000001 MSFT 0100000E)
ACPI: SSDT 000e9200 001B5 (v01 COMPAQ     GTF0 00000001 MSFT 0100000E)
ACPI: SSDT 000e8daa 00155 (v01 COMPAQ   SIDETM 00000001 MSFT 0100000E)
ACPI: SSDT 000e956f 001BA (v01 COMPAQ     GTF2 00000001 MSFT 0100000E)
ACPI: SSDT 000e8eff 000FF (v01 COMPAQ     SATA 00000001 MSFT 0100000E)
ACPI: SSDT 000e8ffe 00101 (v01 COMPAQ   SAT0TM 00000001 MSFT 0100000E)
ACPI: SSDT 000e98e3 000F0 (v01 COMPAQ      L08 00000001 MSFT 0100000E)
ACPI: SSDT 000e9d30 00078 (v01 COMPAQ    FINIS 00000001 MSFT 0100000E)
ACPI: Local APIC address 0xfee00000
899MB HIGHMEM available.
883MB LOWMEM available.
  mapped low ram: 0 - 373fe000
  low ram: 0 - 373fe000
  node 0 low ram: 00000000 - 373fe000
  node 0 bootmap 0000a000 - 00010e80
(9 early reservations) ==> bootmem [0000000000 - 00373fe000]
  #0 [0000000000 - 0000001000]   BIOS data page ==> [0000000000 - 0000001000]
  #1 [0000001000 - 0000002000]    EX TRAMPOLINE ==> [0000001000 - 0000002000]
  #2 [0000006000 - 0000007000]       TRAMPOLINE ==> [0000006000 - 0000007000]
  #3 [0000400000 - 0000ac2a10]    TEXT DATA BSS ==> [0000400000 - 0000ac2a10]
  #4 [000009fc00 - 0000100000]    BIOS reserved ==> [000009fc00 - 0000100000]
  #5 [0000ac3000 - 0000ac70e3]              BRK ==> [0000ac3000 - 0000ac70e3]
  #6 [0000007000 - 000000a000]          PGTABLE ==> [0000007000 - 000000a000]
  #7 [0000ac8000 - 0002085623]      NEW RAMDISK ==> [0000ac8000 - 0002085623]
  #8 [000000a000 - 0000011000]          BOOTMAP ==> [000000a000 - 0000011000]
found SMP MP-table at [c00faa60] faa60
Zone PFN ranges:
  DMA      0x00000000 -> 0x00001000
  Normal   0x00001000 -> 0x000373fe
  HighMem  0x000373fe -> 0x0006f7f0
Movable zone start PFN for each node
early_node_map[2] active PFN ranges
    0: 0x00000000 -> 0x0000009f
    0: 0x00000100 -> 0x0006f7f0
On node 0 totalpages: 456591
free_area_init_node: node 0, pgdat c0978340, node_mem_map c2086000
  DMA zone: 32 pages used for memmap
  DMA zone: 0 pages reserved
  DMA zone: 3967 pages, LIFO batch:0
  Normal zone: 1736 pages used for memmap
  Normal zone: 220470 pages, LIFO batch:31
  HighMem zone: 1800 pages used for memmap
  HighMem zone: 228586 pages, LIFO batch:31
Using APIC driver default
ACPI: PM-Timer IO Port: 0xf808
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
ACPI: LAPIC_NMI (acpi_id[0x02] high edge lint[0x1])
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: IRQ0 used by override.
ACPI: IRQ2 used by override.
ACPI: IRQ9 used by override.
Enabling APIC mode:  Flat.  Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
SMP: Allowing 2 CPUs, 0 hotplug CPUs
nr_irqs_gsi: 24
PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
Allocating PCI resources starting at 70000000 (gap: 70000000:8ec00000)
NR_CPUS:32 nr_cpumask_bits:32 nr_cpu_ids:2 nr_node_ids:1
PERCPU: Embedded 14 pages at c2e7d000, static data 34428 bytes
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 453023
Kernel command line: initrd=initrd.img stage2=hd:LABEL="Fedora" rescue BOOT_IMAGE=vmlinuz PID hash table entries: 4096 (order: 12, 16384 bytes)
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
allocated 9133760 bytes of page_cgroup
please try 'cgroup_disable=memory' option if you don't want memory cgroups
Initializing HighMem for node 0 (000373fe:0006f7f0)
Memory: 1772104k/1826752k available (3495k kernel code, 53368k reserved, 2169k data, 432k init, 921544k highmem)
virtual kernel memory layout:
    fixmap  : 0xffad5000 - 0xfffff000   (5288 kB)
    pkmap   : 0xff400000 - 0xff800000   (4096 kB)
    vmalloc : 0xf7bfe000 - 0xff3fe000   ( 120 MB)
    lowmem  : 0xc0000000 - 0xf73fe000   ( 883 MB)
      .init : 0xc0989000 - 0xc09f5000   ( 432 kB)
      .data : 0xc0769f9b - 0xc0988568   (2169 kB)
      .text : 0xc0400000 - 0xc0769f9b   (3495 kB)
Checking if this processor honours the WP bit even in supervisor mode...Ok.
SLUB: Genslabs=13, HWalign=128, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
Hierarchical RCU implementation.
NR_IRQS:1280
Fast TSC calibration using PIT
Detected 2593.676 MHz processor.
Console: colour VGA+ 80x25
console [tty0] enabled
Calibrating delay loop (skipped), value calculated using timer frequency.. 5187.35 BogoMIPS (lpj=2593676)
Security Framework initialized
SELinux:  Initializing.
SELinux:  Starting in permissive mode
Mount-cache hash table entries: 512
Initializing cgroup subsys ns
Initializing cgroup subsys cpuacct
Initializing cgroup subsys memory
Initializing cgroup subsys devices
Initializing cgroup subsys freezer
Initializing cgroup subsys net_cls
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
mce: CPU supports 4 MCE banks
CPU0: Thermal monitoring enabled (TM1)
Performance Counters: no PMU driver, software counters only.
Checking 'hlt' instruction... OK.
ACPI: Core revision 20090521
ftrace: converting mcount calls to 0f 1f 44 00 00
ftrace: allocating 20202 entries in 40 pages
..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
CPU0: Intel(R) Pentium(R) 4 CPU 2.60GHz stepping 09
Booting processor 1 APIC 0x1 ip 0x6000
Initializing CPU#1
Calibrating delay using timer specific routine.. 5186.35 BogoMIPS (lpj=2593177)
CPU: Trace cache: 12K uops, L1 D cache: 8K
CPU: L2 cache: 512K
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
mce: CPU supports 4 MCE banks
CPU1: Thermal monitoring enabled (TM1)
x86 PAT enabled: cpu 1, old 0x7040600070406, new 0x7010600070106
CPU1: Intel(R) Pentium(R) 4 CPU 2.60GHz stepping 09
checking TSC synchronization [CPU#0 -> CPU#1]: passed.
Brought up 2 CPUs
Total of 2 processors activated (10373.70 BogoMIPS).
sizeof(vma)=84 bytes
sizeof(page)=32 bytes
sizeof(inode)=352 bytes
sizeof(dentry)=132 bytes
sizeof(ext3inode)=500 bytes
sizeof(buffer_head)=56 bytes
sizeof(skbuff)=192 bytes
sizeof(task_struct)=3256 bytes
CPU0 attaching sched-domain:
 domain 0: span 0-1 level SIBLING
  groups: 0 1
CPU1 attaching sched-domain:
 domain 0: span 0-1 level SIBLING
  groups: 1 0
Booting paravirtualized kernel on bare hardware
regulator: core version 0.5
Time: 20:38:38  Date: 11/07/09
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.20 entry at 0xec1a9, last bus=5
PCI: Using configuration type 1 for base access
bio: create slab <bio-0> at 0
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: No dock devices found.
ACPI: PCI Root Bridge [PCI0] (0000:00)
pci 0000:00:00.0: Enabling MCH 'Overflow' Device
pci 0000:00:00.0: reg 10 32bit mmio: [0xf8000000-0xfbffffff]
pci 0000:00:02.0: reg 10 32bit mmio: [0xf0000000-0xf7ffffff]
pci 0000:00:02.0: reg 14 32bit mmio: [0xfc400000-0xfc47ffff]
pci 0000:00:02.0: reg 18 io port: [0x14e0-0x14e7]
pci 0000:00:06.0: reg 10 32bit mmio: [0xfecf0000-0xfecf0fff]
pci 0000:00:1d.0: reg 20 io port: [0x1440-0x145f]
pci 0000:00:1d.1: reg 20 io port: [0x1460-0x147f]
pci 0000:00:1d.2: reg 20 io port: [0x1480-0x149f]
pci 0000:00:1d.7: reg 10 32bit mmio: [0xfc480000-0xfc4803ff]
pci 0000:00:1d.7: PME# supported from D0 D3hot D3cold
pci 0000:00:1d.7: PME# disabled
pci 0000:00:1f.0: Force enabled HPET at 0xfed00000
pci 0000:00:1f.0: Enabled i801 SMBus device
pci 0000:00:1f.0: quirk: region f800-f87f claimed by ICH4 ACPI/GPIO/TCO
pci 0000:00:1f.0: quirk: region fa00-fa3f claimed by ICH4 GPIO
pci 0000:00:1f.1: reg 10 io port: [0x14e8-0x14ef]
pci 0000:00:1f.1: reg 14 io port: [0x1808-0x180b]
pci 0000:00:1f.1: reg 18 io port: [0x14f0-0x14f7]
pci 0000:00:1f.1: reg 1c io port: [0x180c-0x180f]
pci 0000:00:1f.1: reg 20 io port: [0x14c0-0x14cf]
pci 0000:00:1f.1: reg 24 32bit mmio: [0x000000-0x0003ff]
pci 0000:00:1f.2: reg 10 io port: [0x14f8-0x14ff]
pci 0000:00:1f.2: reg 14 io port: [0x1810-0x1813]
pci 0000:00:1f.2: reg 18 io port: [0x1800-0x1807]
pci 0000:00:1f.2: reg 1c io port: [0x1814-0x1817]
pci 0000:00:1f.2: reg 20 io port: [0x14d0-0x14df]
pci 0000:00:1f.3: reg 20 io port: [0xfc00-0xfc1f]
pci 0000:00:1f.5: reg 10 io port: [0x1000-0x10ff]
pci 0000:00:1f.5: reg 14 io port: [0x1400-0x143f]
pci 0000:00:1f.5: reg 18 32bit mmio: [0xfc480400-0xfc4805ff]
pci 0000:00:1f.5: reg 1c 32bit mmio: [0xfc480600-0xfc4806ff]
pci 0000:00:1f.5: PME# supported from D0 D3hot D3cold
pci 0000:00:1f.5: PME# disabled
pci 0000:05:02.0: reg 10 64bit mmio: [0xfc500000-0xfc50ffff]
pci 0000:05:02.0: PME# supported from D3hot D3cold
pci 0000:05:02.0: PME# disabled
pci 0000:00:1e.0: transparent bridge
pci 0000:00:1e.0: bridge 32bit mmio: [0xfc500000-0xfc7fffff]
pci_bus 0000:00: on NUMA node 0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB_._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 *10 11 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 *5 6 7 10 11 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 6 7 10 11 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 7 10 *11 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 *5 6 7 10 11 14 15)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 6 7 10 11 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 *10 11 14 15)
vgaarb: device added: PCI:0000:00:02.0,decodes=io+mem,owns=io+mem,locks=none
vgaarb: loaded
SCSI subsystem initialized
libata version 3.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: old code would have set cacheline size to 128 bytes, but clflush_size = 64
PCI: pci_cache_line_size set to 64 bytes
NetLabel: Initializing
NetLabel:  domain hash size = 128
NetLabel:  protocols = UNLABELED CIPSOv4
NetLabel:  unlabeled traffic allowed by default
hpet clockevent registered
HPET: 3 timers in total, 0 timers will be used for per-cpu timer
hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
hpet0: 3 comparators, 64-bit 14.318180 MHz counter
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp 00:0c: io resource (0xf800-0xf81f) overlaps 0000:00:1f.0 BAR 13 (0xf800-0xf87f), disabling
pnp 00:0c: io resource (0xf820-0xf83f) overlaps 0000:00:1f.0 BAR 13 (0xf800-0xf87f), disabling
pnp 00:0c: io resource (0xf840-0xf85f) overlaps 0000:00:1f.0 BAR 13 (0xf800-0xf87f), disabling
pnp 00:0c: io resource (0xf860-0xf87f) overlaps 0000:00:1f.0 BAR 13 (0xf800-0xf87f), disabling
pnp: PnP ACPI: found 14 devices
ACPI: ACPI bus type pnp unregistered
system 00:0b: ioport range 0x4d0-0x4d1 has been reserved
system 00:0c: ioport range 0x400-0x41f has been reserved
system 00:0c: ioport range 0x420-0x43f has been reserved
system 00:0c: ioport range 0x440-0x45f has been reserved
system 00:0c: ioport range 0x460-0x47f has been reserved
system 00:0c: ioport range 0xfa00-0xfa3f has been reserved
system 00:0c: ioport range 0xfc00-0xfc7f could not be reserved
system 00:0c: ioport range 0xfc80-0xfcff has been reserved
system 00:0c: ioport range 0xfe00-0xfe7f has been reserved
system 00:0c: ioport range 0xfe80-0xfeff has been reserved
system 00:0d: iomem range 0x0-0x9ffff could not be reserved
system 00:0d: iomem range 0x100000-0x6f7fffff could not be reserved
system 00:0d: iomem range 0x6f800000-0x6f8fffff has been reserved
system 00:0d: iomem range 0xe0000-0xfffff could not be reserved
system 00:0d: iomem range 0xfec01000-0xffffffff could not be reserved
system 00:0d: iomem range 0xcc000-0xdffff has been reserved
pci 0000:00:1e.0: PCI bridge, secondary bus 0000:05
pci 0000:00:1e.0:   IO window: disabled
pci 0000:00:1e.0:   MEM window: 0xfc500000-0xfc7fffff
pci 0000:00:1e.0:   PREFETCH window: disabled
pci 0000:00:1e.0: setting latency timer to 64
pci_bus 0000:00: resource 0 io:  [0x00-0xffff]
pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffff]
pci_bus 0000:05: resource 1 mem: [0xfc500000-0xfc7fffff]
pci_bus 0000:05: resource 3 io:  [0x00-0xffff]
pci_bus 0000:05: resource 4 mem: [0x000000-0xffffffff]
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 7, 524288 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
NET: Registered protocol family 1
Trying to unpack rootfs image as initramfs...
Switched to high resolution mode on CPU 1
Switched to high resolution mode on CPU 0
Freeing initrd memory: 22261k freed
apm: BIOS not found.
audit: initializing netlink socket (disabled)
type=2000 audit(1257626318.929:1): initialized
highmem bounce pool size: 64 pages
HugeTLB registered 4 MB page size, pre-allocated 0 pages
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
msgmni has been set to 1706
SELinux:  Registering netfilter hooks
alg: No test for stdrng (krng)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
pci 0000:00:02.0: Boot video device
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
pciehp: PCI Express Hot Plug Controller Driver version: 0.4
acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
acpiphp_glue: can't get bus number, assuming 0
input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0
ACPI: Power Button [PWRF]
input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1
ACPI: Power Button [PBTN]
processor LNXCPU:00: registered as cooling_device0
ACPI: Processor [CPU0] (supports 8 throttling states)
processor LNXCPU:01: registered as cooling_device1
ACPI: Processor [CPU1] (supports 8 throttling states)
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Non-volatile memory driver v1.3
Linux agpgart interface v0.103
agpgart-intel 0000:00:00.0: Intel 865 Chipset
agpgart-intel 0000:00:00.0: detected 8060K stolen memory
agpgart-intel 0000:00:00.0: AGP aperture is 128M @ 0xf0000000
Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
brd: module loaded
loop: module loaded
input: Macintosh mouse button emulation as /devices/virtual/input/input2
ata_piix 0000:00:1f.1: version 2.13
ata_piix 0000:00:1f.1: enabling device (0005 -> 0007)
ata_piix 0000:00:1f.1: PCI INT A -> GSI 18 (level, low) -> IRQ 18
ata_piix 0000:00:1f.1: setting latency timer to 64
scsi0 : ata_piix
scsi1 : ata_piix
ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x14c0 irq 14
ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x14c8 irq 15
ata_piix 0000:00:1f.2: PCI INT A -> GSI 18 (level, low) -> IRQ 18
ata_piix 0000:00:1f.2: MAP [ P0 -- P1 -- ]
ata_piix 0000:00:1f.2: setting latency timer to 64
scsi2 : ata_piix
scsi3 : ata_piix
ata3: SATA max UDMA/133 cmd 0x14f8 ctl 0x1810 bmdma 0x14d0 irq 18
ata4: SATA max UDMA/133 cmd 0x1800 ctl 0x1814 bmdma 0x14d8 irq 18
Fixed MDIO Bus: probed
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ehci_hcd 0000:00:1d.7: PCI INT D -> GSI 23 (level, low) -> IRQ 23
ehci_hcd 0000:00:1d.7: setting latency timer to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
ata1.00: ATA-7: Maxtor 6E040L0, NAR61590, max UDMA/100
ata1.00: 78165360 sectors, multi 16: LBA ata2.00: ATAPI: JLMS XJ-HD166S, DQS7, max UDMA/44
ehci_hcd 0000:00:1d.7: debug port 1
ehci_hcd 0000:00:1d.7: cache line size of 64 is not supported
ehci_hcd 0000:00:1d.7: irq 23, io mem 0xfc480000
ata1.00: configured for UDMA/100
scsi 0:0:0:0: Direct-Access     ATA      Maxtor 6E040L0   NAR6 PQ: 0 ANSI: 5
sd 0:0:0:0: Attached scsi generic sg0 type 0
sd 0:0:0:0: [sda] 78165360 512-byte logical blocks: (40.0 GB/37.2 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
ata2.00: configured for UDMA/44
 sda:
scsi 1:0:0:0: CD-ROM            JLMS     XJ-HD166S        DQS7 PQ: 0 ANSI: 5
sr0: scsi3-mmc drive: 40x/40x cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 1:0:0:0: Attached scsi CD-ROM sr0
sr 1:0:0:0: Attached scsi generic sg1 type 5
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: EHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.31.5-122.fc12.i686 ehci_hcd
usb usb1: SerialNumber: 0000:00:1d.7
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 8 ports detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
uhci_hcd: USB Universal Host Controller Interface driver
uhci_hcd 0000:00:1d.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
uhci_hcd 0000:00:1d.0: setting latency timer to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.0: irq 16, io base 0x00001440
usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: UHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.31.5-122.fc12.i686 uhci_hcd
usb usb2: SerialNumber: 0000:00:1d.0
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 19 (level, low) -> IRQ 19
uhci_hcd 0000:00:1d.1: setting latency timer to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.1: irq 19, io base 0x00001460
usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: UHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.31.5-122.fc12.i686 uhci_hcd
usb usb3: SerialNumber: 0000:00:1d.1
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18
uhci_hcd 0000:00:1d.2: setting latency timer to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.2: irq 18, io base 0x00001480
usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb4: Product: UHCI Host Controller
usb usb4: Manufacturer: Linux 2.6.31.5-122.fc12.i686 uhci_hcd
usb usb4: SerialNumber: 0000:00:1d.2
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
PNP: PS/2 Controller [PNP0303:KBD,PNP0f0e:PS2M] at 0x60,0x64 irq 1,12
 sda1
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
sd 0:0:0:0: [sda] Attached SCSI disk
rtc_cmos 00:03: RTC can wake from S4
rtc_cmos 00:03: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one month, y3k, 114 bytes nvram, hpet irqs
device-mapper: uevent: version 1.0.3
device-mapper: ioctl: 4.15.0-ioctl (2009-04-01) initialised: dm-devel@xxxxxxxxxx
cpuidle: using governor ladder
cpuidle: using governor menu
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 17
Using IPI No-Shortcut mode
PM: Resume from disk failed.
registered taskstats version 1
No TPM chip found, activating TPM-bypass!
  Magic number: 1:260:649
scsi_host host3: hash matches
scsi host3: hash matches
rtc_cmos 00:03: setting system clock to 2009-11-07 20:38:39 UTC (1257626319)
Initalizing network drop monitor service
input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input3
ata3.00: ATA-8: ST3500320AS, SD1A, max UDMA/133
ata3.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 0/32)
ata3.00: configured for UDMA/133
scsi 2:0:0:0: Direct-Access     ATA      ST3500320AS      SD1A PQ: 0 ANSI: 5
sd 2:0:0:0: [sdb] 976773168 512-byte logical blocks: (500 GB/465 GiB)
sd 2:0:0:0: Attached scsi generic sg2 type 0
sd 2:0:0:0: [sdb] Write Protect is off
sd 2:0:0:0: [sdb] Mode Sense: 00 3a 00 00
sd 2:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
 sdb:
psmouse serio1: ID: 10 00 64
 sdb1 sdb2
sd 2:0:0:0: [sdb] Attached SCSI disk
Freeing unused kernel memory: 432k freed
Write protecting the kernel text: 3496k
Write protecting the kernel read-only data: 1696k
input: ImExPS/2 Logitech Wheel Mouse as /devices/platform/i8042/serio1/input/input4
squashfs: version 4.0 (2009/01/31) Phillip Lougher
Loading iSCSI transport class v2.0-870.
iscsi: registered transport (tcp)
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
BIOS EDD facility v0.16 2004-Jun-25, 2 devices found
input: PC Speaker as /devices/platform/pcspkr/input/input5
No iBFT detected.
tg3.c:v3.99 (April 20, 2009)
tg3 0000:05:02.0: PCI INT A -> GSI 20 (level, low) -> IRQ 20
[drm] Initialized drm 1.1.0 20060810
tg3 0000:05:02.0: PME# disabled
eth0: Tigon3 [partno(BCM95782A50) rev 3003] (PCI:33MHz:32-bit) MAC address 00:0d:9d:d9:67:be
eth0: attached PHY is 5705 (10/100/1000Base-T Ethernet) (WireSpeed[0])
eth0: RXcsums[1] LinkChgREG[0] MIirq[0] ASF[0] TSOcap[1]
eth0: dma_rwctrl[763f0000] dma_mask[64-bit]
i915 0000:00:02.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16
i915 0000:00:02.0: setting latency timer to 64
fbcon: inteldrmfb (fb0) is primary device
render error detected, EIR: 0x00000010
[drm:i915_handle_error] *ERROR* EIR stuck: 0x00000010, masking
render error detected, EIR: 0x00000010
[drm] DAC-5: set mode 1280x1024 14
Console: switching to colour frame buffer device 160x64
fb0: inteldrmfb frame buffer device
registered panic notifier
[drm] Initialized i915 1.6.0 20080730 for 0000:00:02.0 on minor 0
ISO 9660 Extensions: Microsoft Joliet Level 3
ISO 9660 Extensions: RRIP_1991A
SELinux: 8192 avtab hash slots, 144734 rules.
SELinux: 8192 avtab hash slots, 144734 rules.
SELinux:  8 users, 12 roles, 2941 types, 136 bools, 1 sens, 1024 cats
SELinux:  75 classes, 144734 rules
SELinux:  Completing initialization.
SELinux:  Setting up existing superblocks.
SELinux: initialized (dev loop0, type squashfs), not configured for labeling
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev securityfs, type securityfs), uses genfs_contexts
SELinux: initialized (dev usbfs, type usbfs), uses genfs_contexts
SELinux: initialized (dev selinuxfs, type selinuxfs), uses genfs_contexts
SELinux: initialized (dev mqueue, type mqueue), uses transition SIDs
SELinux: initialized (dev hugetlbfs, type hugetlbfs), uses transition SIDs
SELinux: initialized (dev devpts, type devpts), uses transition SIDs
SELinux: initialized (dev inotifyfs, type inotifyfs), uses genfs_contexts
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev anon_inodefs, type anon_inodefs), uses genfs_contexts
SELinux: initialized (dev pipefs, type pipefs), uses task SIDs
SELinux: initialized (dev debugfs, type debugfs), uses genfs_contexts
SELinux: initialized (dev sockfs, type sockfs), uses task SIDs
SELinux: initialized (dev proc, type proc), uses genfs_contexts
SELinux: initialized (dev bdev, type bdev), uses genfs_contexts
SELinux: initialized (dev rootfs, type rootfs), uses genfs_contexts
SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts
type=1403 audit(1257626358.753:2): policy loaded auid=4294967295 ses=4294967295
md: raid0 personality registered for level 0
md: raid1 personality registered for level 1
xor: automatically using best checksumming function: pIII_sse
   pIII_sse  :  3276.000 MB/sec
xor: using function: pIII_sse (3276.000 MB/sec)
async_tx: api initialized (async)
raid6: int32x1    542 MB/s
raid6: int32x2    785 MB/s
raid6: int32x4    687 MB/s
raid6: int32x8    468 MB/s
raid6: mmxx1     2128 MB/s
raid6: mmxx2     2414 MB/s
raid6: sse1x1    1261 MB/s
raid6: sse1x2    2121 MB/s
raid6: sse2x1    2535 MB/s
raid6: sse2x2    2636 MB/s
raid6: using algorithm sse2x2 (2636 MB/s)
md: raid6 personality registered for level 6
md: raid5 personality registered for level 5
md: raid4 personality registered for level 4
md: raid10 personality registered for level 10
md: linear personality registered for level -1
device-mapper: multipath: version 1.1.0 loaded
device-mapper: multipath round-robin: version 1.0.0 loaded
usb 1-5: new high speed USB device using ehci_hcd and address 2
usb 1-5: New USB device found, idVendor=0781, idProduct=5406
usb 1-5: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 1-5: Product: U3 Cruzer Micro
usb 1-5: Manufacturer: SanDisk Corporation
usb 1-5: SerialNumber: 0000184DA8604800
usb 1-5: configuration #1 chosen from 1 choice
Initializing USB Mass Storage driver...
scsi4 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 2
usb-storage: waiting for device to settle before scanning
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
usb-storage: device scan complete
scsi 4:0:0:0: Direct-Access     SanDisk  U3 Cruzer Micro  2.18 PQ: 0 ANSI: 2
scsi 4:0:0:1: CD-ROM            SanDisk  U3 Cruzer Micro  2.18 PQ: 0 ANSI: 2
sd 4:0:0:0: Attached scsi generic sg3 type 0
sd 4:0:0:0: [sdc] 8015505 512-byte logical blocks: (4.10 GB/3.82 GiB)
sd 4:0:0:0: [sdc] Write Protect is off
sd 4:0:0:0: [sdc] Mode Sense: 03 00 00 00
sd 4:0:0:0: [sdc] Assuming drive cache: write through
sr1: scsi3-mmc drive: 8x/40x writer xa/form2 cdda tray
sr 4:0:0:1: Attached scsi CD-ROM sr1
sd 4:0:0:0: [sdc] Assuming drive cache: write through
 sdc:
sr 4:0:0:1: Attached scsi generic sg4 type 5
 sdc1
sd 4:0:0:0: [sdc] Assuming drive cache: write through
sd 4:0:0:0: [sdc] Attached SCSI removable disk
SELinux: initialized (dev sdc1, type vfat), uses genfs_contexts


jhhaynes at earthlink dot net

--
fedora-test-list mailing list
fedora-test-list@xxxxxxxxxx
To unsubscribe: https://www.redhat.com/mailman/listinfo/fedora-test-list

[Index of Archives]     [Fedora Desktop]     [Fedora SELinux]     [Photo Sharing]     [Yosemite Forum]     [KDE Users]

  Powered by Linux