Dear list,
I have targeted down the troubles
00:04.0 Ethernet controller: nVidia Corporation nForce2 Ethernet Controller (rev a1)
[root@localhost ~]# service network status
Configured devices:
lo eth0 eth1
Currently active devices:
lo
[root@localhost ~]# uname -r
2.6.29-0.159.rc6.git3.fc11.i586
[root@localhost ~]# service network start
Bringing up loopback interface: [ OK ]
Bringing up interface eth0:
Determining IP information for eth0... failed.
[FAILED]
Bringing up interface eth1: [ OK ]
You have new mail in /var/spool/mail/root
[root@localhost ~]# tail -f /var/log/messages
Feb 27 13:02:21 localhost dhclient: DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 11
Feb 27 13:02:32 localhost dhclient: DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 19
Feb 27 13:02:51 localhost dhclient: DHCPDISCOVER on eth0 to 255.255.255.255 port 67 interval 15
Feb 27 13:03:06 localhost dhclient: No DHCPOFFERS received.
Feb 27 13:03:06 localhost kernel: eth1: setting half-duplex.
Feb 27 13:03:06 localhost kernel: ADDRCONF(NETDEV_UP): eth1: link is not ready
Feb 27 13:03:11 localhost avahi-daemon[1993]: Joining mDNS multicast group on interface eth1.IPv4 with address 192.168.0.1.
Feb 27 13:03:11 localhost avahi-daemon[1993]: New relevant interface eth1.IPv4 for mDNS.
Feb 27 13:03:11 localhost avahi-daemon[1993]: Registering new address record for 192.168.0.1 on eth1.IPv4.
Feb 27 13:03:12 localhost ntpd[1869]: Listening on interface #5 eth1, 192.168.0.1#123 Enabled
^C
[root@localhost ~]# dmesg
Initializing cgroup subsys cpuset
Initializing cgroup subsys cpu
Linux version 2.6.29-0.159.rc6.git3.fc11.i586 (mockbuild@xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx) (gcc version 4.4.0 20090219 (Red Hat 4.4.0-0.21) (GCC) ) #1 SMP Thu Feb 26 12:14:21 EST 2009
KERNEL supported cpus:
Intel GenuineIntel
AMD AuthenticAMD
NSC Geode by NSC
Cyrix CyrixInstead
Centaur CentaurHauls
Transmeta GenuineTMx86
Transmeta TransmetaCPU
UMC UMC UMC UMC
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000002ffd0000 (usable)
BIOS-e820: 000000002ffd0000 - 000000002ffdf000 (ACPI data)
BIOS-e820: 000000002ffdf000 - 0000000030000000 (ACPI NVS)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ff7c0000 - 0000000100000000 (reserved)
DMI 2.3 present.
AMI BIOS detected: BIOS may corrupt low RAM, working around it.
last_pfn = 0x2ffd0 max_arch_pfn = 0x100000
x86 PAT enabled: cpu 0, old 0x7040600070406, new 0x7010600070106
kernel direct mapping tables up to 2ffd0000 @ 10000-16000
Using x86 segment limits to approximate NX protection
RAMDISK: 2fc86000 - 2ffbfc47
ACPI: RSDP 000F97A0, 0014 (r0 ACPIAM)
ACPI: RSDT 2FFD0000, 0030 (r1 A M I OEMRSDT 11000325 MSFT 97)
ACPI: FACP 2FFD0200, 0081 (r2 A M I OEMFACP 11000325 MSFT 97)
FADT: X_PM1a_EVT_BLK.bit_width (16) does not match PM1_EVT_LEN (4)
ACPI: DSDT 2FFD03F0, 39BF (r1 A0007 A0007000 1 INTL 2002026)
ACPI: FACS 2FFDF000, 0040
ACPI: APIC 2FFD0390, 005E (r1 A M I OEMAPIC 11000325 MSFT 97)
ACPI: OEMB 2FFDF040, 0041 (r1 A M I OEMBIOS 11000325 MSFT 97)
ACPI: Local APIC address 0xfee00000
0MB HIGHMEM available.
767MB LOWMEM available.
mapped low ram: 0 - 2ffd0000
low ram: 00000000 - 2ffd0000
bootmap 00011000 - 00016ffc
(9 early reservations) ==> bootmem [0000000000 - 002ffd0000]
#0 [0000000000 - 0000001000] BIOS data page ==> [0000000000 - 0000001000]
#1 [0000001000 - 0000002000] EX TRAMPOLINE ==> [0000001000 - 0000002000]
#2 [0000006000 - 0000007000] TRAMPOLINE ==> [0000006000 - 0000007000]
#3 [0000400000 - 0000fd6bac] TEXT DATA BSS ==> [0000400000 - 0000fd6bac]
#4 [002fc86000 - 002ffbfc47] RAMDISK ==> [002fc86000 - 002ffbfc47]
#5 [0000fd7000 - 0000fdc000] INIT_PG_TABLE ==> [0000fd7000 - 0000fdc000]
#6 [000009fc00 - 0000100000] BIOS reserved ==> [000009fc00 - 0000100000]
#7 [0000010000 - 0000011000] PGTABLE ==> [0000010000 - 0000011000]
#8 [0000011000 - 0000017000] BOOTMAP ==> [0000011000 - 0000017000]
Zone PFN ranges:
DMA 0x00000010 -> 0x00001000
Normal 0x00001000 -> 0x0002ffd0
HighMem 0x0002ffd0 -> 0x0002ffd0
Movable zone start PFN for each node
early_node_map[2] active PFN ranges
0: 0x00000010 -> 0x0000009f
0: 0x00000100 -> 0x0002ffd0
On node 0 totalpages: 196447
free_area_init_node: node 0, pgdat c0898400, node_mem_map c10003c0
DMA zone: 60 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 3923 pages, LIFO batch:0
Normal zone: 2820 pages used for memmap
Normal zone: 189644 pages, LIFO batch:31
Using APIC driver default
Nvidia board detected. Ignoring ACPI timer override.
If you got timer trouble try acpi_use_timer_override
ACPI: PM-Timer IO Port: 0x4008
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 1, version 17, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge)
ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge)
ACPI: IRQ9 used by override.
ACPI: IRQ14 used by override.
ACPI: IRQ15 used by override.
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information
SMP: Allowing 1 CPUs, 0 hotplug CPUs
nr_irqs_gsi: 24
PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
Allocating PCI resources starting at 40000000 (gap: 30000000:cec00000)
NR_CPUS:32 nr_cpumask_bits:32 nr_cpu_ids:1 nr_node_ids:1
PERCPU: Allocating 1351680 bytes of per cpu data
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 193567
Kernel command line: ro root=/dev/VolGroup00/LogVol00
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
CPU 0 irqstacks, hard=c0a9e000 soft=c0a7e000
PID hash table entries: 4096 (order: 12, 16384 bytes)
Fast TSC calibration using PIT
Detected 1913.350 MHz processor.
Console: colour VGA+ 80x25
console [tty0] enabled
Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar
... MAX_LOCKDEP_SUBCLASSES: 8
... MAX_LOCK_DEPTH: 48
... MAX_LOCKDEP_KEYS: 8191
... CLASSHASH_SIZE: 4096
... MAX_LOCKDEP_ENTRIES: 8192
... MAX_LOCKDEP_CHAINS: 16384
... CHAINHASH_SIZE: 8192
memory used by lock dependency info: 2591 kB
per task-struct memory footprint: 1920 bytes
Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
allocated 3930880 bytes of page_cgroup
please try cgroup_disable=memory option if you don't want
Memory: 752564k/786240k available (3027k kernel code, 33056k reserved, 1919k data, 1672k init, 0k highmem)
virtual kernel memory layout:
fixmap : 0xffc56000 - 0xfffff000 (3748 kB)
pkmap : 0xff400000 - 0xff800000 (4096 kB)
vmalloc : 0xf07d0000 - 0xff3fe000 ( 236 MB)
lowmem : 0xc0000000 - 0xeffd0000 ( 767 MB)
.init : 0xc08d9000 - 0xc0a7b000 (1672 kB)
.data : 0xc06f4e5a - 0xc08d4df0 (1919 kB)
.text : 0xc0400000 - 0xc06f4e5a (3027 kB)
Checking if this processor honours the WP bit even in supervisor mode...Ok.
SLUB: Genslabs=12, HWalign=32, Order=0-3, MinObjects=0, CPUs=1, Nodes=1
Calibrating delay loop (skipped), value calculated using timer frequency.. 3826.70 BogoMIPS (lpj=1913350)
Security Framework initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
Mount-cache hash table entries: 512
Initializing cgroup subsys ns
Initializing cgroup subsys cpuacct
Initializing cgroup subsys memory
Initializing cgroup subsys devices
Initializing cgroup subsys freezer
Initializing cgroup subsys net_cls
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 11k freed
ACPI: Core revision 20081204
ftrace: converting mcount calls to 0f 1f 44 00 00
ftrace: allocating 17484 entries in 69 pages
..TIMER: vector=0x30 apic1=0 pin1=0 apic2=-1 pin2=-1
CPU0: AMD Athlon(tm) XP 2600+ stepping 00
APIC calibration not consistent with PM Timer: 98ms instead of 100ms
APIC delta adjusted to PM-Timer: 2079540 (2058464)
Brought up 1 CPUs
Total of 1 processors activated (3826.70 BogoMIPS).
sizeof(vma)=84 bytes
sizeof(page)=60 bytes
sizeof(inode)=648 bytes
sizeof(dentry)=164 bytes
sizeof(ext3inode)=916 bytes
sizeof(buffer_head)=56 bytes
sizeof(skbuff)=184 bytes
sizeof(task_struct)=5308 bytes
CPU0 attaching NULL sched-domain.
khelper used greatest stack depth: 2996 bytes left
net_namespace: 1240 bytes
Booting paravirtualized kernel on bare hardware
regulator: core version 0.5
Time: 18:58:24 Date: 02/27/09
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xf0031, last bus=2
PCI: Using configuration type 1 for base access
bio: create slab <bio-0> at 0
ACPI: EC: Look up EC in DSDT
ACPI: Denied BIOS AML access to invalid port 0x21+0x1 (PIC0)
ACPI Exception (dsopcode-0419): AE_AML_ILLEGAL_ADDRESS, During address validation of OpRegion [IRQM] [20081204]
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S3 S4 S5)
ACPI: Using IOAPIC for interrupt routing
ACPI: No dock devices found.
ACPI: PCI Root Bridge [PCI0] (0000:00)
pci 0000:00:00.0: reg 10 32bit mmio: [0xf4000000-0xf7ffffff]
pci 0000:00:00.0: nForce2 C1 Halt Disconnect fixup
pci 0000:00:01.1: reg 10 io port: [0xef80-0xef9f]
pci 0000:00:01.1: PME# supported from D3hot D3cold
pci 0000:00:01.1: PME# disabled
pci 0000:00:02.0: reg 10 32bit mmio: [0xfe900000-0xfe900fff]
pci 0000:00:02.0: supports D1 D2
pci 0000:00:02.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:02.0: PME# disabled
pci 0000:00:02.1: reg 10 32bit mmio: [0xfea00000-0xfea00fff]
pci 0000:00:02.1: supports D1 D2
pci 0000:00:02.1: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:02.1: PME# disabled
pci 0000:00:02.2: reg 10 32bit mmio: [0xfeb00000-0xfeb000ff]
pci 0000:00:02.2: supports D1 D2
pci 0000:00:02.2: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:02.2: PME# disabled
pci 0000:00:04.0: reg 10 32bit mmio: [0xfe800000-0xfe800fff]
pci 0000:00:04.0: reg 14 io port: [0xeff0-0xeff7]
pci 0000:00:04.0: supports D1 D2
pci 0000:00:04.0: PME# supported from D0 D1 D2 D3hot D3cold
pci 0000:00:04.0: PME# disabled
pci 0000:00:06.0: reg 10 io port: [0xe800-0xe8ff]
pci 0000:00:06.0: reg 14 io port: [0xec00-0xec7f]
pci 0000:00:06.0: reg 18 32bit mmio: [0xfe700000-0xfe700fff]
pci 0000:00:06.0: supports D1 D2
pci 0000:00:09.0: reg 20 io port: [0xffa0-0xffaf]
pci 0000:01:08.0: reg 10 io port: [0xdf00-0xdf3f]
pci 0000:01:08.0: reg 30 32bit mmio: [0xfbe00000-0xfbe0ffff]
pci 0000:00:08.0: bridge io port: [0xd000-0xdfff]
pci 0000:00:08.0: bridge 32bit mmio: [0xfbd00000-0xfbefffff]
pci 0000:02:00.0: reg 10 32bit mmio: [0xfd000000-0xfdffffff]
pci 0000:02:00.0: reg 14 32bit mmio: [0xe8000000-0xefffffff]
pci 0000:02:00.0: reg 30 32bit mmio: [0xfe000000-0xfe01ffff]
pci 0000:00:1e.0: bridge 32bit mmio: [0xfbf00000-0xfe0fffff]
pci 0000:00:1e.0: bridge 32bit mmio pref: [0xe3c00000-0xf3bfffff]
pci_bus 0000:00: on NUMA node 0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P3._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 16) *0, disabled.
ACPI: PCI Interrupt Link [LNKB] (IRQs 18) *11
ACPI: PCI Interrupt Link [LNKC] (IRQs 18) *11
ACPI: PCI Interrupt Link [LNKD] (IRQs 19) *0, disabled.
ACPI: PCI Interrupt Link [LNKE] (IRQs 16) *0, disabled.
ACPI: PCI Interrupt Link [LUS0] (IRQs 20 21 22) *10
ACPI: PCI Interrupt Link [LUS1] (IRQs 20 21 22) *7
ACPI: PCI Interrupt Link [LUS2] (IRQs 20 21 22) *5
ACPI: PCI Interrupt Link [LKLN] (IRQs 20 21 22) *11
ACPI: PCI Interrupt Link [LAPU] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [LAUI] (IRQs 20 21 22) *11
ACPI: PCI Interrupt Link [LKMO] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [LKSM] (IRQs 23) *10
ACPI: PCI Interrupt Link [LFWR] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [LETH] (IRQs 20 21 22) *0, disabled.
ACPI: PCI Interrupt Link [LATA] (IRQs 20 21 22) *14
ACPI Warning (tbutils-0242): Incorrect checksum in table [OEMB] - 76, should be 6B [20081204]
SCSI subsystem initialized
libata version 3.00 loaded.
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
DMA-API: preallocated 8192 debug entries
DMA-API: debugging enabled by kernel config
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 14 devices
ACPI: ACPI bus type pnp unregistered
system 00:06: ioport range 0x4d0-0x4d1 has been reserved
system 00:07: iomem range 0xfec00000-0xfec00fff has been reserved
system 00:07: iomem range 0xfee00000-0xfeefffff could not be reserved
system 00:07: iomem range 0xff780000-0xff7bffff has been reserved
system 00:0a: ioport range 0x480-0x487 has been reserved
system 00:0a: ioport range 0xd00-0xd07 has been reserved
system 00:0d: iomem range 0x0-0x9ffff could not be reserved
system 00:0d: iomem range 0xc0000-0xdffff could not be reserved
system 00:0d: iomem range 0xe0000-0xfffff could not be reserved
system 00:0d: iomem range 0x100000-0x2fffffff could not be reserved
system 00:0d: iomem range 0xff7c0000-0xffffffff has been reserved
pci 0000:00:08.0: PCI bridge, secondary bus 0000:01
pci 0000:00:08.0: IO window: 0xd000-0xdfff
pci 0000:00:08.0: MEM window: 0xfbd00000-0xfbefffff
pci 0000:00:08.0: PREFETCH window: disabled
pci 0000:00:1e.0: PCI bridge, secondary bus 0000:02
pci 0000:00:1e.0: IO window: disabled
pci 0000:00:1e.0: MEM window: 0xfbf00000-0xfe0fffff
pci 0000:00:1e.0: PREFETCH window: 0x000000e3c00000-0x000000f3bfffff
pci 0000:00:08.0: setting latency timer to 64
pci_bus 0000:00: resource 0 io: [0x00-0xffff]
pci_bus 0000:00: resource 1 mem: [0x000000-0xffffffff]
pci_bus 0000:01: resource 0 io: [0xd000-0xdfff]
pci_bus 0000:01: resource 1 mem: [0xfbd00000-0xfbefffff]
pci_bus 0000:01: resource 2 mem: [0x0-0x0]
pci_bus 0000:01: resource 3 mem: [0x0-0x0]
pci_bus 0000:02: resource 0 mem: [0x0-0x0]
pci_bus 0000:02: resource 1 mem: [0xfbf00000-0xfe0fffff]
pci_bus 0000:02: resource 2 mem: [0xe3c00000-0xf3bfffff]
pci_bus 0000:02: resource 3 mem: [0x0-0x0]
NET: Registered protocol family 2
IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
TCP bind hash table entries: 65536 (order: 9, 2621440 bytes)
TCP: Hash tables configured (established 131072 bind 65536)
TCP reno registered
NET: Registered protocol family 1
checking if image is initramfs... it is
Freeing initrd memory: 3303k freed
apm: BIOS version 1.2 Flags 0x03 (Driver version 1.16ac)
apm: overridden by ACPI.
audit: initializing netlink socket (disabled)
type=2000 audit(1235761103.966:1): initialized
HugeTLB registered 4 MB page size, pre-allocated 0 pages
khelper used greatest stack depth: 2776 bytes left
VFS: Disk quotas dquot_6.5.2
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Created ptmx node in devpts ino 2
msgmni has been set to 1476
SELinux: Registering netfilter hooks
alg: No test for stdrng (krng)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
io scheduler noop registered
io scheduler cfq registered (default)
pci 0000:02:00.0: Boot video device
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
pciehp: PCI Express Hot Plug Controller Driver version: 0.4
acpiphp: ACPI Hot Plug PCI Controller Driver version: 0.5
Switched to high resolution mode on CPU 0
input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0
ACPI: Power Button (FF) [PWRF]
input: Power Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1
ACPI: Power Button (CM) [PWRB]
processor ACPI_CPU:00: registered as cooling_device0
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Non-volatile memory driver v1.3
Linux agpgart interface v0.103
agpgart: Detected NVIDIA nForce2 chipset
agpgart-nvidia 0000:00:00.0: AGP aperture is 64M @ 0xf4000000
Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:0b: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:0c: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
brd: module loaded
loop: module loaded
Fixed MDIO Bus: probed
input: Macintosh mouse button emulation as /devices/virtual/input/input2
Driver 'sd' needs updating - please use bus_type methods
Driver 'sr' needs updating - please use bus_type methods
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
ACPI: PCI Interrupt Link [LUS2] enabled at IRQ 22
ehci_hcd 0000:00:02.2: PCI INT C -> Link[LUS2] -> GSI 22 (level, high) -> IRQ 22
ehci_hcd 0000:00:02.2: setting latency timer to 64
ehci_hcd 0000:00:02.2: EHCI Host Controller
ehci_hcd 0000:00:02.2: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:02.2: debug port 1
ehci_hcd 0000:00:02.2: cache line size of 64 is not supported
ehci_hcd 0000:00:02.2: irq 22, io mem 0xfeb00000
ehci_hcd 0000:00:02.2: USB 2.0 started, EHCI 1.00
usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb1: Product: EHCI Host Controller
usb usb1: Manufacturer: Linux 2.6.29-0.159.rc6.git3.fc11.i586 ehci_hcd
usb usb1: SerialNumber: 0000:00:02.2
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 6 ports detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
ACPI: PCI Interrupt Link [LUS0] enabled at IRQ 21
ohci_hcd 0000:00:02.0: PCI INT A -> Link[LUS0] -> GSI 21 (level, high) -> IRQ 21
ohci_hcd 0000:00:02.0: setting latency timer to 64
ohci_hcd 0000:00:02.0: OHCI Host Controller
ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:02.0: irq 21, io mem 0xfe900000
usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb2: Product: OHCI Host Controller
usb usb2: Manufacturer: Linux 2.6.29-0.159.rc6.git3.fc11.i586 ohci_hcd
usb usb2: SerialNumber: 0000:00:02.0
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 3 ports detected
ACPI: PCI Interrupt Link [LUS1] enabled at IRQ 20
ohci_hcd 0000:00:02.1: PCI INT B -> Link[LUS1] -> GSI 20 (level, high) -> IRQ 20
ohci_hcd 0000:00:02.1: setting latency timer to 64
ohci_hcd 0000:00:02.1: OHCI Host Controller
ohci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 3
ohci_hcd 0000:00:02.1: irq 20, io mem 0xfea00000
usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
usb usb3: Product: OHCI Host Controller
usb usb3: Manufacturer: Linux 2.6.29-0.159.rc6.git3.fc11.i586 ohci_hcd
usb usb3: SerialNumber: 0000:00:02.1
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 3 ports detected
uhci_hcd: USB Universal Host Controller Interface driver
PNP: PS/2 Controller [PNP0303:PS2K,PNP0f12:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
rtc_cmos 00:02: RTC can wake from S4
rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0
rtc0: alarms up to one year, y3k, 114 bytes nvram
device-mapper: uevent: version 1.0.3
device-mapper: ioctl: 4.14.0-ioctl (2008-04-23) initialised: dm-devel@xxxxxxxxxx
cpuidle: using governor ladder
cpuidle: using governor menu
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
usbhid: v2.6:USB HID core driver
nf_conntrack version 0.5.0 (12285 buckets, 49140 max)
CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
nf_conntrack.acct=1 kernel paramater, acct=1 nf_conntrack module option or
sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
ip_tables: (C) 2000-2006 Netfilter Core Team
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 17
Using IPI No-Shortcut mode
registered taskstats version 1
Magic number: 13:356:1000
pnp1: hash matches
rtc_cmos 00:02: hash matches
Freeing unused kernel memory: 1672k freed
Write protecting the kernel read-only data: 1448k
input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input3
setfont used greatest stack depth: 2736 bytes left
psmouse serio1: ID: 10 00 64<7>pata_amd 0000:00:09.0: version 0.4.1
pata_amd 0000:00:09.0: setting latency timer to 64
scsi0 : pata_amd
scsi1 : pata_amd
ata1: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xffa0 irq 14
ata2: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xffa8 irq 15
usb 2-2: new full speed USB device using ohci_hcd and address 2
ata1.00: ATA-7: MAXTOR STM3320620A, 3.AAD, max UDMA/100
ata1.00: 625142448 sectors, multi 16: LBA48
ata1: nv_mode_filter: 0x3f39f&0x3f01f->0x3f01f, BIOS=0x3f000 (0xc600c0c0) ACPI=0x3f01f (17:120:0x11)
usb 2-2: New USB device found, idVendor=03f0, idProduct=0304
usb 2-2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 2-2: Product: DeskJet 810C
usb 2-2: Manufacturer: Hewlett-Packard
usb 2-2: SerialNumber: MY94M1621WGI
usb 2-2: configuration #1 chosen from 1 choice
ata1.00: configured for UDMA/100
scsi 0:0:0:0: Direct-Access ATA MAXTOR STM332062 3.AA PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 625142448 512-byte hardware sectors: (320 GB/298 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 625142448 512-byte hardware sectors: (320 GB/298 GiB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2 < sda5 sda6 > sda3 sda4
sd 0:0:0:0: [sda] Attached SCSI disk
sd 0:0:0:0: Attached scsi generic sg0 type 0
input: ImPS/2 Generic Wheel Mouse as /devices/platform/i8042/serio1/input/input4
ata2.00: ATAPI: TSSTcorpCD/DVDW SH-S182D, SB03, max UDMA/33
ata2.01: ATAPI: SONY CD-RW CRX216E, PD01, max UDMA/33
ata2: nv_mode_filter: 0x739f&0x701f->0x701f, BIOS=0x7000 (0xc600c0c0) ACPI=0x701f (54:54:0x15)
ata2: nv_mode_filter: 0x739f&0x701f->0x701f, BIOS=0x7000 (0xc600c0c0) ACPI=0x701f (54:54:0x15)
ata2.00: configured for UDMA/33
ata2.01: configured for UDMA/33
scsi 1:0:0:0: CD-ROM TSSTcorp CD/DVDW SH-S182D SB03 PQ: 0 ANSI: 5
sr0: scsi3-mmc drive: 48x/48x writer dvd-ram cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 1:0:0:0: Attached scsi CD-ROM sr0
sr 1:0:0:0: Attached scsi generic sg1 type 5
scsi 1:0:1:0: CD-ROM SONY CD-RW CRX216E PD01 PQ: 0 ANSI: 5
sr1: scsi3-mmc drive: 88x/48x writer cd/rw xa/form2 cdda tray
sr 1:0:1:0: Attached scsi CD-ROM sr1
sr 1:0:1:0: Attached scsi generic sg2 type 5
modprobe used greatest stack depth: 800 bytes left
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
type=1404 audit(1235761110.651:2): enforcing=1 old_enforcing=0 auid=4294967295 ses=4294967295
SELinux: 8192 avtab hash slots, 118978 rules.
SELinux: 8192 avtab hash slots, 118978 rules.
SELinux: 8 users, 13 roles, 2732 types, 120 bools, 1 sens, 1024 cats
SELinux: 74 classes, 118978 rules
SELinux: Completing initialization.
SELinux: Setting up existing superblocks.
SELinux: initialized (dev dm-0, type ext3), uses xattr
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev usbfs, type usbfs), uses genfs_contexts
SELinux: initialized (dev selinuxfs, type selinuxfs), uses genfs_contexts
SELinux: initialized (dev mqueue, type mqueue), uses transition SIDs
SELinux: initialized (dev hugetlbfs, type hugetlbfs), uses genfs_contexts
SELinux: initialized (dev devpts, type devpts), uses transition SIDs
SELinux: initialized (dev inotifyfs, type inotifyfs), uses genfs_contexts
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev anon_inodefs, type anon_inodefs), uses genfs_contexts
SELinux: initialized (dev pipefs, type pipefs), uses task SIDs
SELinux: initialized (dev debugfs, type debugfs), uses genfs_contexts
SELinux: initialized (dev sockfs, type sockfs), uses task SIDs
SELinux: initialized (dev proc, type proc), uses genfs_contexts
SELinux: initialized (dev bdev, type bdev), uses genfs_contexts
SELinux: initialized (dev rootfs, type rootfs), uses genfs_contexts
SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts
type=1403 audit(1235761111.477:3): policy loaded auid=4294967295 ses=4294967295
udev: starting version 137
input: PC Speaker as /devices/platform/pcspkr/input/input5
usblp0: Disabling reads from problematic bidirectional printer
usblp0: USB Unidirectional printer dev 2 if 0 alt 1 proto 2 vid 0x03F0 pid 0x0304
usbcore: registered new interface driver usblp
forcedeth: Reverse Engineered nForce ethernet driver. Version 0.62.
ACPI: PCI Interrupt Link [LKLN] enabled at IRQ 22
forcedeth 0000:00:04.0: PCI INT A -> Link[LKLN] -> GSI 22 (level, high) -> IRQ 22
forcedeth 0000:00:04.0: setting latency timer to 64
nv_probe: set workaround bit for reversed mac addr
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 18
3c59x 0000:01:08.0: PCI INT A -> Link[LNKC] -> GSI 18 (level, high) -> IRQ 18
3c59x: Donald Becker and others.
0000:01:08.0: 3Com PCI 3c905 Boomerang 100baseTx at 0001df00.
eth0 (3c59x): not using net_device_ops yet
forcedeth 0000:00:04.0: ifname eth1, PHY OUI 0x732 @ 1, addr 00:0e:a6:42:59:af
forcedeth 0000:00:04.0: timirq lnktim desc-v1
i2c-adapter i2c-0: nForce2 SMBus adapter at 0x4300
i2c-adapter i2c-1: nForce2 SMBus adapter at 0x4340
ACPI: PCI Interrupt Link [LAUI] enabled at IRQ 21
Intel ICH 0000:00:06.0: PCI INT A -> Link[LAUI] -> GSI 21 (level, high) -> IRQ 21
Intel ICH 0000:00:06.0: setting latency timer to 64
intel8x0_measure_ac97_clock: measured 50690 usecs
intel8x0: clocking to 47398
udev: renamed network interface eth1 to eth0
udev: renamed network interface eth0_rename to eth1
EXT3 FS on dm-0, internal journal
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda3, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: initialized (dev sda3, type ext3), uses xattr
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
swap_cgroup: uses 1540 bytes of vmalloc for pointer array space and 1576960 bytes to hold mem_cgroup pointers on swap
swap_cgroup can be disabled by noswapaccount boot option.
Adding 1574328k swap on /dev/sda5. Priority:-1 extents:1 across:1574328k
swap_cgroup: uses 1504 bytes of vmalloc for pointer array space and 1540096 bytes to hold mem_cgroup pointers on swap
swap_cgroup can be disabled by noswapaccount boot option.
Adding 1540088k swap on /dev/mapper/VolGroup00-LogVol01. Priority:-2 extents:1 across:1540088k
SELinux: initialized (dev binfmt_misc, type binfmt_misc), uses genfs_contexts
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
ip6_tables: (C) 2000-2006 Netfilter Core Team
RPC: Registered udp transport module.
RPC: Registered tcp transport module.
SELinux: initialized (dev rpc_pipefs, type rpc_pipefs), uses genfs_contexts
SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
Bluetooth: Core ver 2.14
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.11
Bluetooth: L2CAP socket layer initialized
Bluetooth: BNEP (Ethernet Emulation) ver 1.3
Bluetooth: BNEP filters: protocol multicast
Bridge firewalling registered
Bluetooth: SCO (Voice Link) ver 0.6
Bluetooth: SCO socket layer initialized
[drm] Initialized drm 1.1.0 20060810
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 18
pci 0000:02:00.0: PCI INT A -> Link[LNKB] -> GSI 18 (level, high) -> IRQ 18
[drm] Detected an NV30 generation card (0x034200a2)
[drm] Initialized nouveau 0.0.12 20060213 on minor 0
agpgart-nvidia 0000:00:00.0: AGP 3.0 bridge
agpgart: Xorg tried to set rate=x12. Setting to AGP3 x8 mode.
agpgart-nvidia 0000:00:00.0: putting AGP V3 device into 8x mode
pci 0000:02:00.0: putting AGP V3 device into 8x mode
[drm] Allocating FIFO number 0
[drm] nouveau_fifo_alloc: initialised FIFO 0
[drm] Allocating FIFO number 1
[drm] nouveau_fifo_alloc: initialised FIFO 1
fuse init (API version 7.11)
SELinux: initialized (dev fuse, type fuse), uses genfs_contexts
eth0: no link during initialization.
ADDRCONF(NETDEV_UP): eth0: link is not ready
eth0: link up.
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
------------[ cut here ]------------
WARNING: at lib/dma-debug.c:461 check_unmap+0xf6/0x3d8() (Not tainted)
Hardware name: System product name
forcedeth 0000:00:04.0: DMA-API: device driver tries to free DMA memory it has not allocated [device address=0x000000001048ea72] [size=90 bytes]
Modules linked in: fuse nouveau drm sco bridge stp llc bnep l2cap bluetooth autofs4 sunrpc nf_conntrack_netbios_ns iptable_nat nf_nat ip6t_REJECT ip6table_filter ip6_tables ipv6 uinput snd_intel8x0 snd_ac97_codec ac97_bus snd_seq_dummy snd_seq_oss snd_seq_midi_event snd_seq snd_seq_device snd_pcm_oss snd_mixer_oss i2c_nforce2 3c59x i2c_core snd_pcm forcedeth mii snd_timer snd usblp pcspkr soundcore snd_page_alloc pata_ali sata_vsc sata_svw sata_via pata_pcmcia sata_nv ata_generic pata_acpi pata_amd [last unloaded: scsi_wait_scan]
Pid: 0, comm: swapper Not tainted 2.6.29-0.159.rc6.git3.fc11.i586 #1
Call Trace:
[<c042fe03>] warn_slowpath+0x7c/0xa7
[<c044e373>] ? find_usage_backwards+0xc8/0xea
[<c044e373>] ? find_usage_backwards+0xc8/0xea
[<c044ffed>] ? check_usage+0x29/0x20a
[<c044f686>] ? mark_lock+0x1e/0x30b
[<c054a200>] ? task_current_syscall+0x7a/0x8e
[<c054a2ee>] ? get_hash_bucket+0x26/0x2f
[<c054aa52>] check_unmap+0xf6/0x3d8
[<c0430313>] ? release_console_sem+0x1a9/0x1d6
[<c044f686>] ? mark_lock+0x1e/0x30b
[<c054aea1>] debug_dma_unmap_page+0x5b/0x63
[<c054aea1>] ? debug_dma_unmap_page+0x5b/0x63
[<f0eea3e6>] T.907+0x34/0x3f [forcedeth]
[<f0eea42c>] nv_tx_done+0x3b/0x187 [forcedeth]
[<f0eea61c>] nv_nic_irq+0xa4/0x238 [forcedeth]
[<c047105b>] handle_IRQ_event+0x22/0x58
[<c047247c>] handle_fasteoi_irq+0x80/0xb7
[<c04723fc>] ? handle_fasteoi_irq+0x0/0xb7
<IRQ> [<c04045ac>] ? common_interrupt+0x2c/0x40
[<c044fbc2>] ? trace_hardirqs_on+0xb/0xd
[<c041b94c>] ? native_safe_halt+0xa/0xc
[<c0409703>] ? default_idle+0x4f/0x89
[<c044ee6d>] ? trace_hardirqs_off+0xb/0xd
[<c0403010>] ? cpu_idle+0x72/0x92
[<c06df85f>] ? rest_init+0x53/0x55
---[ end trace 8157a52088604c67 ]---
eth0: no IPv6 routers present
eth1: setting half-duplex.
ADDRCONF(NETDEV_UP): eth1: link is not ready
I guess I need to open a bug, I see when I have a chance to do it. I believe it looks like a kernel oops.
Regards,
Antonio
--
fedora-test-list mailing list
fedora-test-list@xxxxxxxxxx
To unsubscribe:
https://www.redhat.com/mailman/listinfo/fedora-test-list
