While trying to use dvgrab to input DV from an ADVC-100 Firewire
device on my DELL Inspiron 8600 laptop, I got the following
console message:
=============================================
[ INFO: possible recursive locking detected ]
2.6.23-0.222.rc9.git4.fc8 #1
---------------------------------------------
X/2522 is trying to acquire lock:
(&q->lock){++..}, at: [<c042671c>] __wake_up+0x15/0x42
but task is already holding lock:
(&q->lock){++..}, at: [<c042671c>] __wake_up+0x15/0x42
other info that might help us debug this:
2 locks held by X/2522:
#0: (&client->lock){.+..}, at: [<e0993f51>] queue_event+0x2b/0x68
[firewire_core]
#1: (&q->lock){++..}, at: [<c042671c>] __wake_up+0x15/0x42
stack backtrace:
[<c0406463>] show_trace_log_lvl+0x1a/0x2f
[<c0406e4d>] show_trace+0x12/0x14
[<c0406e65>] dump_stack+0x16/0x18
[<c0449c56>] __lock_acquire+0x189/0xc67
[<c044abae>] lock_acquire+0x7b/0x9e
[<c0634712>] _spin_lock_irqsave+0x4a/0x77
[<c042671c>] __wake_up+0x15/0x42
[<c04aed7e>] ep_poll_safewake+0x86/0xa8
[<c04afa05>] ep_poll_callback+0x9f/0xaa
[<c042483e>] __wake_up_common+0x32/0x55
[<c0426738>] __wake_up+0x31/0x42
[<e0993f7d>] queue_event+0x57/0x68 [firewire_core]
[<e0994a5a>] handle_request+0xd8/0xe0 [firewire_core]
[<e099269a>] fw_core_handle_request+0x215/0x23c [firewire_core]
[<e0961c42>] handle_ar_packet+0xd7/0xeb [firewire_ohci]
[<e0962bac>] ar_context_tasklet+0xb6/0xc4 [firewire_ohci]
[<c0432b5b>] tasklet_action+0x68/0xd3
[<c0432a39>] __do_softirq+0x78/0xff
[<c04075d4>] do_softirq+0x74/0xf7
=======================
full dmesg output is attached.
Pat
---
Linux version 2.6.23-0.222.rc9.git4.fc8 (kojibuilder@) (gcc version 4.1.2 20070925 (Red Hat 4.1.2-31)) #1 SMP Sat Oct 6 13:53:58 EDT 2007
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009f000 (usable)
BIOS-e820: 000000000009f000 - 00000000000a0000 (reserved)
BIOS-e820: 0000000000100000 - 000000001ffae000 (usable)
BIOS-e820: 000000001ffae000 - 0000000020000000 (reserved)
BIOS-e820: 00000000feda0000 - 00000000fee00000 (reserved)
BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved)
0MB HIGHMEM available.
511MB LOWMEM available.
Using x86 segment limits to approximate NX protection
Entering add_active_range(0, 0, 130990) 0 entries of 256 used
Zone PFN ranges:
DMA 0 -> 4096
Normal 4096 -> 130990
HighMem 130990 -> 130990
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0 -> 130990
On node 0 totalpages: 130990
DMA zone: 56 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 4040 pages, LIFO batch:0
Normal zone: 1734 pages used for memmap
Normal zone: 125160 pages, LIFO batch:31
HighMem zone: 0 pages used for memmap
Movable zone: 0 pages used for memmap
DMI 2.3 present.
Using APIC driver default
ACPI: RSDP 000FDF00, 0014 (r0 DELL )
ACPI: RSDT 1FFF0000, 0028 (r1 DELL CPi R 27D5061E ASL 61)
ACPI: FACP 1FFF0400, 0074 (r1 DELL CPi R 27D5061E ASL 61)
ACPI: DSDT 1FFF0C00, 2E13 (r1 INT430 SYSFexxx 1001 MSFT 100000E)
ACPI: FACS 1FFFF800, 0040
ACPI: PM-Timer IO Port: 0x808
Allocating PCI resources starting at 30000000 (gap: 20000000:deda0000)
swsusp: Registered nosave memory region: 000000000009f000 - 00000000000a0000
swsusp: Registered nosave memory region: 00000000000a0000 - 0000000000100000
Built 1 zonelists in Zone order. Total pages: 129200
Kernel command line: ro root=LABEL=/1 rhgb quiet
Local APIC disabled by BIOS -- you can enable it with "lapic"
mapped APIC to ffffb000 (01758000)
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Initializing CPU#0
CPU 0 irqstacks, hard=c0814000 soft=c07f4000
PID hash table entries: 2048 (order: 11, 8192 bytes)
Detected 1398.831 MHz processor.
Console: colour VGA+ 80x25
console [tty0] enabled
Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar
... MAX_LOCKDEP_SUBCLASSES: 8
... MAX_LOCK_DEPTH: 30
... MAX_LOCKDEP_KEYS: 2048
... CLASSHASH_SIZE: 1024
... MAX_LOCKDEP_ENTRIES: 8192
... MAX_LOCKDEP_CHAINS: 16384
... CHAINHASH_SIZE: 8192
memory used by lock dependency info: 1024 kB
per task-struct memory footprint: 1680 bytes
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 505632k/523960k available (2271k kernel code, 17784k reserved, 1175k data, 568k init, 0k highmem)
virtual kernel memory layout:
fixmap : 0xffc53000 - 0xfffff000 (3760 kB)
pkmap : 0xff800000 - 0xffc00000 (4096 kB)
vmalloc : 0xe0800000 - 0xff7fe000 ( 495 MB)
lowmem : 0xc0000000 - 0xdffae000 ( 511 MB)
.init : 0xc0763000 - 0xc07f1000 ( 568 kB)
.data : 0xc0637dd7 - 0xc075da44 (1175 kB)
.text : 0xc0400000 - 0xc0637dd7 (2271 kB)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
SLUB: Genslabs=22, HWalign=64, Order=0-1, MinObjects=4, CPUs=1, Nodes=1
Calibrating delay using timer specific routine.. 2800.16 BogoMIPS (lpj=1400083)
Security Framework v1.0.0 initialized
SELinux: Initializing.
SELinux: Starting in permissive mode
selinux_register_security: Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 512
CPU: After generic identify, caps: a7e9f9bf 00000000 00000000 00000000 00000180 00000000 00000000 00000000
CPU: L1 I cache: 32K, L1 D cache: 32K
CPU: L2 cache: 1024K
CPU: After all inits, caps: a7e9f1bf 00000000 00000000 00002040 00000180 00000000 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Compat vDSO mapped to ffffe000.
Checking 'hlt' instruction... OK.
SMP alternatives: switching to UP code
Freeing SMP alternatives: 12k freed
ACPI: Core revision 20070126
ACPI: setting ELCR to 0200 (from 0800)
CPU0: Intel(R) Pentium(R) M processor 1400MHz stepping 05
SMP motherboard not detected.
Local APIC not detected. Using dummy APIC emulation.
Brought up 1 CPUs
sizeof(vma)=84 bytes
sizeof(page)=56 bytes
sizeof(inode)=604 bytes
sizeof(dentry)=160 bytes
sizeof(ext3inode)=856 bytes
sizeof(buffer_head)=56 bytes
sizeof(skbuff)=180 bytes
sizeof(task_struct)=3376 bytes
khelper used greatest stack depth: 3160 bytes left
Booting paravirtualized kernel on bare hardware
khelper used greatest stack depth: 3084 bytes left
Time: 11:25:21 Date: 09/08/107
NET: Registered protocol family 16
ACPI: ACPI Dock Station Driver
ACPI: bus type pci registered
PCI: PCI BIOS revision 2.10 entry at 0xfc96e, last bus=2
PCI: Using configuration type 1
Setting up standard PCI resources
ACPI: EC: Look up EC in DSDT
ACPI: Interpreter enabled
ACPI: (supports S0 S1 S3 S4 S5)
ACPI: Using PIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (0000:00)
Force enabled HPET at base address 0xfed00000
PCI quirk: region 0800-087f claimed by ICH4 ACPI/GPIO/TCO
PCI quirk: region 0880-08bf claimed by ICH4 GPIO
PCI: Transparent bridge - 0000:00:1e.0
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGP_._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIE._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 9 10 *11)
ACPI: PCI Interrupt Link [LNKB] (IRQs 5 7) *11
ACPI: PCI Interrupt Link [LNKC] (IRQs 9 10 *11)
ACPI: PCI Interrupt Link [LNKD] (IRQs 5 7 9 10 *11)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
ACPI: bus type pnp registered
pnp: PnP ACPI: found 13 devices
ACPI: ACPI bus type pnp unregistered
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
hpet clockevent registered
hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
hpet0: 3 64-bit timers, 14318180 Hz
Time: tsc clocksource has been installed.
pnp: 00:00: iomem range 0x0-0x9fbff could not be reserved
pnp: 00:00: iomem range 0x9fc00-0x9ffff could not be reserved
pnp: 00:00: iomem range 0xc0000-0xcffff could not be reserved
pnp: 00:00: iomem range 0xe0000-0xfffff could not be reserved
pnp: 00:02: ioport range 0x4d0-0x4d1 has been reserved
pnp: 00:02: ioport range 0x800-0x805 has been reserved
pnp: 00:02: ioport range 0x808-0x80f has been reserved
pnp: 00:03: ioport range 0xf400-0xf4fe has been reserved
pnp: 00:03: ioport range 0x806-0x807 has been reserved
pnp: 00:03: ioport range 0x810-0x85f has been reserved
pnp: 00:03: ioport range 0x860-0x87f has been reserved
pnp: 00:03: ioport range 0x880-0x8bf has been reserved
pnp: 00:03: ioport range 0x8c0-0x8df has been reserved
pnp: 00:08: ioport range 0x900-0x97f has been reserved
PCI: Bridge: 0000:00:01.0
IO window: c000-cfff
MEM window: fc000000-fdffffff
PREFETCH window: d0000000-dfffffff
PCI: Bus 3, cardbus bridge: 0000:02:01.0
IO window: 0000d000-0000d0ff
IO window: 0000d400-0000d4ff
PREFETCH window: 30000000-33ffffff
MEM window: 38000000-3bffffff
PCI: Bridge: 0000:00:1e.0
IO window: d000-efff
MEM window: f6000000-fbffffff
PREFETCH window: 30000000-33ffffff
PCI: Setting latency timer of device 0000:00:1e.0 to 64
PCI: Enabling device 0000:02:01.0 (0000 -> 0003)
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI Interrupt 0000:02:01.0[A] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
NET: Registered protocol family 2
IP route cache hash table entries: 4096 (order: 2, 16384 bytes)
TCP established hash table entries: 16384 (order: 7, 655360 bytes)
TCP bind hash table entries: 16384 (order: 7, 589824 bytes)
TCP: Hash tables configured (established 16384 bind 16384)
TCP reno registered
checking if image is initramfs... it is
Switched to high resolution mode on CPU 0
Freeing initrd memory: 2916k freed
khelper used greatest stack depth: 2956 bytes left
apm: BIOS not found.
audit: initializing netlink socket (disabled)
audit(1191842720.968:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
SELinux: Registering netfilter hooks
ksign: Installing public key data
Loading keyring
- Added public key 4961170A4469D9B5
- User ID: Red Hat, Inc. (Kernel Module GPG key)
Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
Boot video device is 0000:01:00.0
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3] C4[C3])
ACPI: Processor [CPU0] (supports 8 throttling states)
ACPI: Thermal Zone [THM] (53 C)
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Real Time Clock Driver v1.12ac
Non-volatile memory driver v1.2
Linux agpgart interface v0.102
agpgart: Detected an Intel 855PM Chipset.
agpgart: AGP aperture is 128M @ 0xe0000000
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:0b: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 5
PCI: setting IRQ 5 as level-triggered
ACPI: PCI Interrupt 0000:00:1f.6[B] -> Link [LNKB] -> GSI 5 (level, low) -> IRQ 5
ACPI: PCI interrupt for device 0000:00:1f.6 disabled
RAMDISK driver initialized: 16 RAM disks of 16384K size 4096 blocksize
input: Macintosh mouse button emulation as /class/input/input0
Yenta: CardBus bridge found at 0000:02:01.0 [1028:016a]
Yenta: Using CSCINT to route CSC interrupts to PCI
Yenta: Routing CardBus interrupts to PCI
Yenta TI: socket 0000:02:01.0, mfunc 0x012c1202, devctl 0x64
Yenta: ISA IRQ mask 0x04d8, PCI irq 11
Socket status: 30000086
Yenta: Raising subordinate bus# of parent bus (#02) from #02 to #06
pcmcia: parent PCI bridge I/O window: 0xd000 - 0xefff
cs: IO port probe 0xd000-0xefff: clean.
pcmcia: parent PCI bridge Memory window: 0xf6000000 - 0xfbffffff
pcmcia: parent PCI bridge Memory window: 0x30000000 - 0x33ffffff
PNP: PS/2 Controller [PNP0303:KBC,PNP0f13:PS2M] at 0x60,0x64 irq 1,12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard as /class/input/input1
cpuidle: using governor menu
usbcore: registered new interface driver hiddev
usbcore: registered new interface driver usbhid
drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
Using IPI No-Shortcut mode
Magic number: 11:165:428
Freeing unused kernel memory: 568k freed
Write protecting the kernel read-only data: 877k
Marking TSC unstable due to: TSC halts in idle.
Time: hpet clocksource has been installed.
ACPI: PCI Interrupt Link [LNKH] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:1d.7[D] -> Link [LNKH] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:1d.7 to 64
ehci_hcd 0000:00:1d.7: EHCI Host Controller
ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:1d.7: debug port 1
PCI: cache line size of 32 is not supported by device 0000:00:1d.7
ehci_hcd 0000:00:1d.7: irq 11, io mem 0xf4fffc00
ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 6 ports detected
insmod used greatest stack depth: 1876 bytes left
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
USB Universal Host Controller Interface driver v3.0
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:1d.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:1d.0 to 64
uhci_hcd 0000:00:1d.0: UHCI Host Controller
uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
uhci_hcd 0000:00:1d.0: irq 11, io base 0x0000bf80
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:1d.1[B] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:1d.1 to 64
uhci_hcd 0000:00:1d.1: UHCI Host Controller
uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
uhci_hcd 0000:00:1d.1: irq 11, io base 0x0000bf40
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
input: PS/2 Mouse as /class/input/input2
input: AlpsPS/2 ALPS GlidePoint as /class/input/input3
ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 11
ACPI: PCI Interrupt 0000:00:1d.2[C] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:1d.2 to 64
uhci_hcd 0000:00:1d.2: UHCI Host Controller
uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
uhci_hcd 0000:00:1d.2: irq 11, io base 0x0000bf20
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
SCSI subsystem initialized
usb 3-1: new low speed USB device using uhci_hcd and address 2
libata version 2.21 loaded.
ata_piix 0000:00:1f.1: version 2.12
PCI: Enabling device 0000:00:1f.1 (0005 -> 0007)
ACPI: PCI Interrupt 0000:00:1f.1[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
PCI: Setting latency timer of device 0000:00:1f.1 to 64
scsi0 : ata_piix
scsi1 : ata_piix
ata1: PATA max UDMA/100 cmd 0x000101f0 ctl 0x000103f6 bmdma 0x0001bfa0 irq 14
ata2: PATA max UDMA/100 cmd 0x00010170 ctl 0x00010376 bmdma 0x0001bfa8 irq 15
usb 3-1: configuration #1 chosen from 1 choice
input: Microsoft Microsoft USB Mouse as /class/input/input4
input: USB HID v1.10 Mouse [Microsoft Microsoft USB Mouse] on usb-0000:00:1d.1-1
ata1.00: ATA-6: TOSHIBA MK4025GAS, KA100A, max UDMA/100
ata1.00: 78140160 sectors, multi 8: LBA
ata1.00: configured for UDMA/100
ata2.00: ATAPI: HL-DT-STCD-RW/DVD-ROM GCC-4241N, A100, max UDMA/33
ata2.00: configured for UDMA/33
scsi 0:0:0:0: Direct-Access ATA TOSHIBA MK4025GA KA10 PQ: 0 ANSI: 5
sd 0:0:0:0: [sda] 78140160 512-byte hardware sectors (40008 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sd 0:0:0:0: [sda] 78140160 512-byte hardware sectors (40008 MB)
sd 0:0:0:0: [sda] Write Protect is off
sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
sda: sda1 sda2 sda3
sd 0:0:0:0: [sda] Attached SCSI disk
scsi 1:0:0:0: CD-ROM HL-DT-ST RW/DVD GCC-4241N A100 PQ: 0 ANSI: 5
insmod used greatest stack depth: 760 bytes left
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
security: 5 users, 11 roles, 2284 types, 107 bools, 1 sens, 1024 cats
security: 67 classes, 227364 rules
SELinux: Completing initialization.
SELinux: Setting up existing superblocks.
SELinux: initialized (dev sda1, type ext3), uses xattr
SELinux: initialized (dev usbfs, type usbfs), uses genfs_contexts
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev debugfs, type debugfs), uses genfs_contexts
SELinux: initialized (dev selinuxfs, type selinuxfs), uses genfs_contexts
SELinux: initialized (dev mqueue, type mqueue), uses transition SIDs
SELinux: initialized (dev hugetlbfs, type hugetlbfs), uses genfs_contexts
SELinux: initialized (dev devpts, type devpts), uses transition SIDs
SELinux: initialized (dev inotifyfs, type inotifyfs), uses genfs_contexts
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
SELinux: initialized (dev futexfs, type futexfs), uses genfs_contexts
SELinux: initialized (dev anon_inodefs, type anon_inodefs), uses genfs_contexts
SELinux: initialized (dev pipefs, type pipefs), uses task SIDs
SELinux: initialized (dev sockfs, type sockfs), uses task SIDs
SELinux: initialized (dev cpuset, type cpuset), uses genfs_contexts
SELinux: initialized (dev proc, type proc), uses genfs_contexts
SELinux: initialized (dev bdev, type bdev), uses genfs_contexts
SELinux: initialized (dev rootfs, type rootfs), uses genfs_contexts
SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts
audit(1191842728.467:2): policy loaded auid=4294967295
sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.20
sr 1:0:0:0: Attached scsi CD-ROM sr0
sd 0:0:0:0: Attached scsi generic sg0 type 0
sr 1:0:0:0: Attached scsi generic sg1 type 5
cs: IO port probe 0x100-0x3af: excluding 0x378-0x37f
cs: IO port probe 0x3e0-0x4ff: clean.
cs: IO port probe 0x820-0x8ff: clean.
cs: IO port probe 0xc00-0xcf7: clean.
cs: IO port probe 0xa00-0xaff: clean.
intel_rng: FWH not detected
ACPI: AC Adapter [AC] (on-line)
ACPI: Battery Slot [BAT0] (battery present)
ACPI: Battery Slot [BAT1] (battery absent)
input: Lid Switch as /class/input/input5
ACPI: Lid Switch [LID]
input: Power Button (CM) as /class/input/input6
ACPI: Power Button (CM) [PBTN]
input: Sleep Button (CM) as /class/input/input7
ACPI: Sleep Button (CM) [SBTN]
iTCO_vendor_support: vendor-support=0
iTCO_wdt: Intel TCO WatchDog Timer Driver v1.02 (26-Jul-2007)
iTCO_wdt: Found a ICH4-M TCO device (Version=1, TCOBASE=0x0860)
iTCO_wdt: initialized. heartbeat=30 sec (nowayout=0)
ieee80211_crypt: registered algorithm 'NULL'
ieee80211: 802.11 data/management/control stack, git-1.1.13
ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@xxxxxxxxxxxxxxx>
ACPI: PCI Interrupt 0000:02:00.0[A] -> Link [LNKC] -> GSI 11 (level, low) -> IRQ 11
ssb: Sonics Silicon Backplane found on PCI device 0000:02:00.0
b44.c:v2.0
eth0: Broadcom 44xx/47xx 10/100BaseT Ethernet 00:0d:56:36:9e:58
ipw2100: Intel(R) PRO/Wireless 2100 Network Driver, git-1.2.2
ipw2100: Copyright(c) 2003-2006 Intel Corporation
ACPI: PCI Interrupt 0000:02:03.0[A] -> Link [LNKB] -> GSI 5 (level, low) -> IRQ 5
ipw2100: Detected Intel PRO/Wireless 2100 Network Connection
input: Video Bus as /class/input/input8
ACPI: Video Device [VID] (multi-head: yes rom: no post: no)
parport_pc 00:0c: reported by Plug and Play ACPI
parport0: PC-style at 0x378 (0x778), irq 7 [PCSPP,TRISTATE]
ACPI: PCI Interrupt 0000:02:01.1[A] -> Link [LNKD] -> GSI 11 (level, low) -> IRQ 11
firewire_ohci: Added fw-ohci device 0000:02:01.1, OHCI version 1.10
ACPI: PCI Interrupt 0000:00:1f.5[B] -> Link [LNKB] -> GSI 5 (level, low) -> IRQ 5
PCI: Setting latency timer of device 0000:00:1f.5 to 64
firewire_core: created new fw device fw0 (0 config rom retries, S400)
intel8x0_measure_ac97_clock: measured 50820 usecs
intel8x0: clocking to 48000
ACPI: PCI Interrupt 0000:00:1f.6[B] -> Link [LNKB] -> GSI 5 (level, low) -> IRQ 5
PCI: Setting latency timer of device 0000:00:1f.6 to 64
MC'97 1 converters and GPIO not ready (0xff00)
audit(1191842739.681:3): avc: denied { read } for pid=1262 comm="salsa" name="asound.state" dev=sda1 ino=482591 scontext=system_u:system_r:udev_t:s0-s0:c0.c1023 tcontext=system_u:object_r:var_lib_t:s0 tclass=file
audit(1191842739.681:4): avc: denied { getattr } for pid=1262 comm="salsa" path="/var/lib/alsa/asound.state" dev=sda1 ino=482591 scontext=system_u:system_r:udev_t:s0-s0:c0.c1023 tcontext=system_u:object_r:var_lib_t:s0 tclass=file
SELinux: initialized (dev ramfs, type ramfs), uses genfs_contexts
NET: Registered protocol family 10
lo: Disabled Privacy Extensions
floppy0: no floppy controllers found
ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKA] -> GSI 11 (level, low) -> IRQ 11
device-mapper: ioctl: 4.11.0-ioctl (2006-10-12) initialised: dm-devel@xxxxxxxxxx
device-mapper: multipath: version 1.0.5 loaded
EXT3 FS on sda1, internal journal
SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
kjournald starting. Commit interval 5 seconds
EXT3 FS on sda2, internal journal
EXT3-fs: mounted filesystem with ordered data mode.
SELinux: initialized (dev sda2, type ext3), uses xattr
Adding 610460k swap on /dev/sda3. Priority:-1 extents:1 across:610460k
SELinux: initialized (dev binfmt_misc, type binfmt_misc), uses genfs_contexts
IA-32 Microcode Update Driver: v1.14a <tigran@xxxxxxxxxxxxxxxxxxxx>
Clocksource tsc unstable (delta = -137031157 ns)
ADDRCONF(NETDEV_UP): eth0: link is not ready
audit(1191842761.673:5): avc: denied { read write } for pid=1745 comm="consoletype" path="/dev/pts/0" dev=devpts ino=2 scontext=system_u:system_r:consoletype_t:s0 tcontext=system_u:object_r:rhgb_devpts_t:s0 tclass=chr_file
audit(1191842761.675:6): avc: denied { getattr } for pid=1745 comm="consoletype" path="/dev/pts/0" dev=devpts ino=2 scontext=system_u:system_r:consoletype_t:s0 tcontext=system_u:object_r:rhgb_devpts_t:s0 tclass=chr_file
b44: eth0: Link is up at 100 Mbps, full duplex.
b44: eth0: Flow control is off for TX and off for RX.
ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
audit(1191842765.313:7): audit_pid=1873 old=0 by auid=4294967295 subj=system_u:system_r:auditd_t:s0
SELinux: initialized (dev rpc_pipefs, type rpc_pipefs), uses genfs_contexts
Bluetooth: Core ver 2.11
NET: Registered protocol family 31
Bluetooth: HCI device and connection manager initialized
Bluetooth: HCI socket layer initialized
Bluetooth: L2CAP ver 2.8
Bluetooth: L2CAP socket layer initialized
Bluetooth: RFCOMM socket layer initialized
Bluetooth: RFCOMM TTY layer initialized
Bluetooth: RFCOMM ver 1.8
eth0: no IPv6 routers present
SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
SELinux: initialized (dev autofs, type autofs), uses genfs_contexts
usb 2-1: new full speed USB device using uhci_hcd and address 2
usb 2-1: configuration #1 chosen from 1 choice
usblp0: USB Bidirectional printer dev 2 if 0 alt 1 proto 2 vid 0x1453 pid 0x2000
usbcore: registered new interface driver usblp
usblp0: nonzero read bulk status received: -84
usblp0: nonzero write bulk status received: -71
usblp0: error -71 reading printer status
usb 2-1: USB disconnect, address 2
usblp0: removed
usb 3-1: USB disconnect, address 2
b44: eth0: Link is down.
firewire_core: created new fw device fw1 (0 config rom retries, S400)
firewire_core: phy config: card 0, new root=ffc1, gap_count=5
=============================================
[ INFO: possible recursive locking detected ]
2.6.23-0.222.rc9.git4.fc8 #1
---------------------------------------------
X/2522 is trying to acquire lock:
(&q->lock){++..}, at: [<c042671c>] __wake_up+0x15/0x42
but task is already holding lock:
(&q->lock){++..}, at: [<c042671c>] __wake_up+0x15/0x42
other info that might help us debug this:
2 locks held by X/2522:
#0: (&client->lock){.+..}, at: [<e0993f51>] queue_event+0x2b/0x68 [firewire_core]
#1: (&q->lock){++..}, at: [<c042671c>] __wake_up+0x15/0x42
stack backtrace:
[<c0406463>] show_trace_log_lvl+0x1a/0x2f
[<c0406e4d>] show_trace+0x12/0x14
[<c0406e65>] dump_stack+0x16/0x18
[<c0449c56>] __lock_acquire+0x189/0xc67
[<c044abae>] lock_acquire+0x7b/0x9e
[<c0634712>] _spin_lock_irqsave+0x4a/0x77
[<c042671c>] __wake_up+0x15/0x42
[<c04aed7e>] ep_poll_safewake+0x86/0xa8
[<c04afa05>] ep_poll_callback+0x9f/0xaa
[<c042483e>] __wake_up_common+0x32/0x55
[<c0426738>] __wake_up+0x31/0x42
[<e0993f7d>] queue_event+0x57/0x68 [firewire_core]
[<e0994a5a>] handle_request+0xd8/0xe0 [firewire_core]
[<e099269a>] fw_core_handle_request+0x215/0x23c [firewire_core]
[<e0961c42>] handle_ar_packet+0xd7/0xeb [firewire_ohci]
[<e0962bac>] ar_context_tasklet+0xb6/0xc4 [firewire_ohci]
[<c0432b5b>] tasklet_action+0x68/0xd3
[<c0432a39>] __do_softirq+0x78/0xff
[<c04075d4>] do_softirq+0x74/0xf7
=======================
--
fedora-test-list mailing list
fedora-test-list@xxxxxxxxxx
To unsubscribe:
https://www.redhat.com/mailman/listinfo/fedora-test-list
