I installed the new kernel-2.6.16-1.2069_FC4 and my machine starts to boot
and then says:
ata1: failed to set xfermode, disabled
ata2: failed to set xfermode, disabled
Then it complains that it can't find any volume groups, there is one, but I
don't think that it can see my SATA disks. It prints out a few more things
and panics. I am running Fedora Core 4, planning on going to 5 after it has
settled some.
Grub kernel line:
kernel /vmlinuz-2.6.16-1.2069_FC4 ro root=/dev/V0/L1 acpi=off rhgb quiet
Should I try something else on the kernel command line?
Thanks!
Jerry
With 2.6.15-1.1833_FC4 kernel some of dmesg looks like:
CPU: AMD Athlon(tm) XP 2600+ stepping 01
PCI: Bypassing VIA 8237 APIC De-Assert Message
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
VP_IDE: IDE controller at PCI slot 0000:00:0f.1
PCI: Via IRQ fixup for 0000:00:0f.1, from 255 to 0
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8237 (rev 00) IDE UDMA133 controller on pci0000:00:0f.1
ide0: BM-DMA at 0xfc00-0xfc07, BIOS settings: hda:pio, hdb:DMA
ide1: BM-DMA at 0xfc08-0xfc0f, BIOS settings: hdc:DMA, hdd:pio
Probing IDE interface ide0...
hdb: Pioneer DVD-ROM ATAPIModel DVD-500M 010, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: SONY DVD RW DRU-510A, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hdb: ATAPI 40X DVD-ROM drive, 512kB Cache, UDMA(66)
Uniform CD-ROM driver Revision: 3.20
hdc: ATAPI 32X DVD-ROM DVD-R CD-R/RW drive, 8192kB Cache, UDMA(33)
SCSI subsystem initialized
libata version 1.20 loaded.
sata_via 0000:00:0f.0: version 1.1
sata_via 0000:00:0f.0: routed to hard irq line 11
ata1: SATA max UDMA/133 cmd 0xE800 ctl 0xE402 bmdma 0xD800 irq 11
ata2: SATA max UDMA/133 cmd 0xE000 ctl 0xDC02 bmdma 0xD808 irq 11
ata1: SATA link up 1.5 Gbps (SStatus 113)
ata1: dev 0 cfg 49:2f00 82:7c6b 83:7f09 84:4003 85:7c69 86:3e01 87:4003
88:407f
ata1: dev 0 ATA-7, max UDMA/133, 490234752 sectors: LBA48
ata1: dev 0 configured for UDMA/133
scsi0 : sata_via
ata2: SATA link up 1.5 Gbps (SStatus 113)
ata2: dev 0 cfg 49:2f00 82:7c6b 83:7f09 84:4003 85:7c69 86:3e01 87:4003
88:407f
ata2: dev 0 ATA-7, max UDMA/133, 490234752 sectors: LBA48
ata2: dev 0 configured for UDMA/133
scsi1 : sata_via
Vendor: ATA Model: Maxtor 6Y250M0 Rev: YAR5
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sda: 490234752 512-byte hdwr sectors (251000 MB)
SCSI device sda: drive cache: write back
SCSI device sda: 490234752 512-byte hdwr sectors (251000 MB)
SCSI device sda: drive cache: write back
sda: sda1 sda2 sda3 < sda5 sda6 sda7 >
sd 0:0:0:0: Attached scsi disk sda
Vendor: ATA Model: Maxtor 6Y250M0 Rev: YAR5
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sdb: 490234752 512-byte hdwr sectors (251000 MB)
SCSI device sdb: drive cache: write back
SCSI device sdb: 490234752 512-byte hdwr sectors (251000 MB)
SCSI device sdb: drive cache: write back
sdb: sdb1 sdb2 sdb3 < sdb5 sdb6 sdb7 >
sd 1:0:0:0: Attached scsi disk sdb
device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel@xxxxxxxxxx
--
fedora-test-list mailing list
fedora-test-list@xxxxxxxxxx
To unsubscribe:
https://www.redhat.com/mailman/listinfo/fedora-test-list