kernel-2.6.15-1.1955_FC5.src.rpm and suspend/wake

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



I have started to see a lot of I/O errors on my system since I started to test suspend. (see below). Do these indicate hardware problems or software ? I have also included a snip of dmesg where the suspend /wake messages show up. Only problem I see is in an acpi event which is not handled. I/O errors seem to occur only during startup.

If these are hardware errors are there any Linux OSS utilities to mark bad sectors on mounted volumes or do a non-destructive surface scan ?

sample I/O errors: (note: hdc is my lvm partition, hda is windows fat32, hdb is /boot)

hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x51 { IllegalLengthIndication LastFailedSense=0x05 }
ide: failed opcode was: unknown
end_request: I/O error, dev hdc, sector 0
printk: 464 messages suppressed.
Buffer I/O error on device hdc, logical block 0
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x51 { IllegalLengthIndication LastFailedSense=0x05 }
ide: failed opcode was: unknown
end_request: I/O error, dev hdc, sector 8
Buffer I/O error on device hdc, logical block 1
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x51 { IllegalLengthIndication LastFailedSense=0x05 }
ide: failed opcode was: unknown
end_request: I/O error, dev hdc, sector 16
Buffer I/O error on device hdc, logical block 2
hdc: command error: status=0x51 { DriveReady SeekComplete Error }
hdc: command error: error=0x51 { IllegalLengthIndication LastFailedSense=0x05 }
ide: failed opcode was: unknown

snip of dmesg with suspend/wake:

usb 1-2: USB disconnect, address 2
audit(:0): major=252 name_count=0: freeing multiple contexts (1)
audit(:0): major=113 name_count=0: freeing multiple contexts (2)
PM: Preparing system for mem sleep
Freezing cpus ...
Stopping tasks: ==============================================================================================|
ndiswrapper (pnp_set_power_state:424): query power returns C0000001
ndiswrapper (miniport_set_power_state:1208): setting power state to 4 failed: C00000BB ndiswrapper (miniport_set_power_state:1210): device may not support power management
pnp: Device 00:08 disabled.
PM: Entering mem sleep
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU0: Intel P4/Xeon Extended MCE MSRs (12) available
CPU0: Thermal LVT vector (0xf0) already installed
Back to C!
PM: Finishing wakeup.
ACPI: PCI Interrupt 0000:00:1d.0[A] -> Link [LNKA] -> GSI 10 (level, low) -> IRQ 10
PCI: Setting latency timer of device 0000:00:1d.0 to 64
usb usb1: root hub lost power or was reset
ACPI: PCI Interrupt 0000:00:1d.1[B] -> Link [LNKD] -> GSI 9 (level, low) -> IRQ 9
PCI: Setting latency timer of device 0000:00:1d.1 to 64
usb usb2: root hub lost power or was reset
PCI: Setting latency timer of device 0000:00:1e.0 to 64
ACPI: PCI Interrupt 0000:00:1f.1[A] -> Link [LNKC] -> GSI 9 (level, low) -> IRQ 9 ACPI: PCI Interrupt 0000:00:1f.5[B] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10
PCI: Setting latency timer of device 0000:00:1f.5 to 64
ACPI: PCI Interrupt 0000:00:1f.6[B] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10
PCI: Setting latency timer of device 0000:00:1f.6 to 64
ACPI: PCI Interrupt 0000:01:00.0[A] -> Link [LNKA] -> GSI 10 (level, low) -> IRQ 10 ACPI: PCI Interrupt 0000:02:04.0[A] -> Link [LNKA] -> GSI 10 (level, low) -> IRQ 10
Yenta O2: res at 0x94/0xD4: ca/00
Yenta O2: enabling read prefetch/write burst
ACPI: PCI Interrupt 0000:02:04.1[B] -> Link [LNKB] -> GSI 10 (level, low) -> IRQ 10
pnp: Device 00:05 does not supported activation.
pnp: Device 00:06 does not supported activation.
pnp: Device 00:08 activated.
ndiswrapper (IoCreateUnprotectedSymbolicLink:739): --UNIMPLEMENTED--
ndiswrapper: using irq 10
Restarting tasks... done
Thawing cpus ...
ACPI Error (evevent-0312): No installed handler for fixed event [00000002] [20060127]
ACPI: Power Button (FF) [PWRF]
ACPI: Lid Switch [LID]
ACPI: Power Button (CM) [PWRB]
audit(:0): major=252 name_count=0: freeing multiple contexts (1)
audit(:0): major=113 name_count=0: freeing multiple contexts (2)
agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V2 device at 0000:00:00.0 into 1x mode
agpgart: Putting AGP V2 device at 0000:01:00.0 into 1x mode
eth0: link down
ADDRCONF(NETDEV_UP): eth0: link is not ready
eth1: no IPv6 routers present
usb 2-2: new low speed USB device using uhci_hcd and address 2
usb 2-2: configuration #1 chosen from 1 choice
input: Microsoft Microsoft 5-Button Mouse with IntelliEye(TM) as /class/input/input4 input: USB HID v1.10 Mouse [Microsoft Microsoft 5-Button Mouse with IntelliEye(TM)] on usb-0000:00:1d.1-2
[don@localhost ~]$


--
fedora-test-list mailing list
fedora-test-list@xxxxxxxxxx
To unsubscribe: https://www.redhat.com/mailman/listinfo/fedora-test-list

[Index of Archives]     [Fedora Desktop]     [Fedora SELinux]     [Photo Sharing]     [Yosemite Forum]     [KDE Users]