Hello, I have been trying to get Xen working with the most recent kernel builds from Rawhide. When I boot using Xen and kernel-xen0 the network fails and I get tracebacks on the console. Booting starts as expected but starting eth0 seems to take a little longer than normal. The problems begin when NTP is started, booting pauses here for quite a few seconds and then a traceback appears. Booting eventually continues with these pauses and tracebacks. When the system is finally up I can login is root and the network appears to be up (according to ifconfig) but I cannot ping any other local devices and the RX and TX values for eth0 remain at zero. Attached is a console log from booting - the interesting stuff is towards the end, the output of lspci, and my grub.conf I am running FC4T1 with kernel and xen updated from Rawhide: kernel-xen0-2.6.11-1.1226_FC4 kernel-smp-2.6.11-1.1226_FC4 kernel-2.6.11-1.1226_FC4 kernel-xenU-2.6.11-1.1226_FC4 The Ethernet port works fine under the standard SMP kernel. Is anyone else seeing this? Keith.
00:00.0 Host bridge: Intel Corporation 915G/P/GV Processor to I/O Controller (rev 04) 00:01.0 PCI bridge: Intel Corporation 915G/P/GV PCI Express Root Port (rev 04) 00:1c.0 PCI bridge: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) PCI Express Port 1 (rev 03) 00:1d.0 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #1 (rev 03) 00:1d.1 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #2 (rev 03) 00:1d.2 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #3 (rev 03) 00:1d.3 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB UHCI #4 (rev 03) 00:1d.7 USB Controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) USB2 EHCI Controller (rev 03) 00:1e.0 PCI bridge: Intel Corporation 82801 PCI Bridge (rev d3) 00:1e.2 Multimedia audio controller: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) AC'97 Audio Controller (rev 03) 00:1f.0 ISA bridge: Intel Corporation 82801FB/FR (ICH6/ICH6R) LPC Interface Bridge (rev 03) 00:1f.1 IDE interface: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) IDE Controller (rev 03) 00:1f.2 IDE interface: Intel Corporation 82801FB/FW (ICH6/ICH6W) SATA Controller (rev 03) 00:1f.3 SMBus: Intel Corporation 82801FB/FBM/FR/FW/FRW (ICH6 Family) SMBus Controller (rev 03) 01:00.0 VGA compatible controller: ATI Technologies Inc RV370 5B60 [Radeon X300 (PCIE)] 01:00.1 Display controller: ATI Technologies Inc: Unknown device 5b70 03:01.0 Modem: Intel Corporation: Unknown device 1080 (rev 04) 03:08.0 Ethernet controller: Intel Corporation 82562ET/EZ/GT/GZ - PRO/100 VE (LOM) Ethernet Controller (rev 03)
__ __ _____ ___ _ _ \ \/ /___ _ __ |___ / / _ \ __| | _____ _____| | \ // _ \ '_ \ |_ \| | | |__ / _` |/ _ \ \ / / _ \ | / \ __/ | | | ___) | |_| |__| (_| | __/\ V / __/ | /_/\_\___|_| |_| |____(_)___/ \__,_|\___| \_/ \___|_| http://www.cl.cam.ac.uk/netos/xen University of Cambridge Computer Laboratory Xen version 3.0-devel (bhcompile@xxxxxxxxxxxxxxxx) (gcc version 4.0.0 200503295 Latest ChangeSet: information unavailable (XEN) Physical RAM map: (XEN) 0000000000000000 - 00000000000a0000 (usable) (XEN) 00000000000f0000 - 0000000000100000 (reserved) (XEN) 0000000000100000 - 000000003fe88c00 (usable) (XEN) 000000003fe88c00 - 000000003fe8ac00 (ACPI NVS) (XEN) 000000003fe8ac00 - 000000003fe8cc00 (ACPI data) (XEN) 000000003fe8cc00 - 0000000040000000 (reserved) (XEN) 00000000e0000000 - 00000000f0000000 (reserved) (XEN) 00000000fec00000 - 00000000fed00400 (reserved) (XEN) 00000000fed20000 - 00000000feda0000 (reserved) (XEN) 00000000fee00000 - 00000000fef00000 (reserved) (XEN) 00000000ffb00000 - 0000000100000000 (reserved) (XEN) System RAM: 1022MB (1046688kB) (XEN) Xen heap: 10MB (10828kB) (XEN) CPU0: Before vendor init, caps: bfebfbff 00000000 00000000, vendor = 0 (XEN) CPU#0: Physical ID: 0, Logical ID: 0 (XEN) CPU caps: bfebfbff 00000000 00000000 00000000 (XEN) found SMP MP-table at 000fe710 (XEN) ACPI: RSDP (v000 DELL ) @ 0x000fec00 (XEN) ACPI: RSDT (v001 DELL 4700 0x00000007 ASL 0x00000061) @ 0x000fcc10 (XEN) ACPI: FADT (v001 DELL 4700 0x00000007 ASL 0x00000061) @ 0x000fcc50 (XEN) ACPI: SSDT (v001 DELL st_ex 0x00001000 MSFT 0x0100000d) @ 0xfffc58e5 (XEN) ACPI: MADT (v001 DELL 4700 0x00000007 ASL 0x00000061) @ 0x000fccc4 (XEN) ACPI: BOOT (v001 DELL 4700 0x00000007 ASL 0x00000061) @ 0x000fcd36 (XEN) ACPI: ASF! (v016 DELL 4700 0x00000007 ASL 0x00000061) @ 0x000fcd5e (XEN) ACPI: MCFG (v001 DELL 4700 0x00000007 ASL 0x00000061) @ 0x000fcdc5 (XEN) ACPI: HPET (v001 DELL 4700 0x00000007 ASL 0x00000061) @ 0x000fce03 (XEN) ACPI: DSDT (v001 DELL dt_ex 0x00001000 MSFT 0x0100000d) @ 0x00000000 (XEN) ACPI: Local APIC address 0xfee00000 (XEN) ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) (XEN) Processor #0 Unknown CPU [15:3] APIC version 20 (XEN) ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled) (XEN) Processor #1 Unknown CPU [15:3] APIC version 20 (XEN) ACPI: LAPIC (acpi_id[0x03] lapic_id[0x01] disabled) (XEN) ACPI: LAPIC (acpi_id[0x04] lapic_id[0x07] disabled) (XEN) ACPI: LAPIC_NMI (acpi_id[0xff] high level lint[0x1]) (XEN) Using ACPI for processor (LAPIC) configuration information (XEN) Intel MultiProcessor Specification v1.4 (XEN) Virtual Wire compatibility mode. (XEN) OEM ID: DELL Product ID: Dim 4700 APIC at: 0xFEE00000 (XEN) I/O APIC #8 Version 32 at 0xFEC00000. (XEN) Enabling APIC mode: Flat. Using 1 I/O APICs (XEN) Processors: 2 (XEN) Using scheduler: Borrowed Virtual Time (bvt) (XEN) Initializing CPU#0 (XEN) Detected 2992.657 MHz processor. (XEN) CPU0: Before vendor init, caps: bfebfbff 00000000 00000000, vendor = 0 (XEN) CPU#0: Physical ID: 0, Logical ID: 0 (XEN) CPU caps: bfebfbff 00000000 00000000 00000000 (XEN) CPU0 booted (XEN) enabled ExtINT on CPU#0 (XEN) ESR value before enabling vector: 00000040 (XEN) ESR value after enabling vector: 00000000 (XEN) Booting processor 1/1 eip 90000 (XEN) Initializing CPU#1 (XEN) masked ExtINT on CPU#1 (XEN) ESR value before enabling vector: 00000000 (XEN) ESR value after enabling vector: 00000000 (XEN) CPU1: Before vendor init, caps: bfebfbff 00000000 00000000, vendor = 0 (XEN) CPU#1: Physical ID: 0, Logical ID: 1 (XEN) CPU caps: bfebfbff 00000000 00000000 00000000 (XEN) CPU1 has booted. (XEN) Total of 2 processors activated. (XEN) ENABLING IO-APIC IRQs (XEN) Setting 8 in the phys_id_present_map (XEN) ...changing IO-APIC physical APIC ID to 8 ... ok. (XEN) init IO_APIC IRQs (XEN) vector_irq[49] = 1 (XEN) vector_irq[51] = 3 (XEN) vector_irq[59] = 4 (XEN) vector_irq[61] = 5 (XEN) vector_irq[69] = 6 (XEN) vector_irq[71] = 7 (XEN) vector_irq[79] = 8 (XEN) vector_irq[81] = 9 (XEN) vector_irq[89] = 10 (XEN) vector_irq[91] = 11 (XEN) vector_irq[99] = 12 (XEN) vector_irq[a1] = 14 (XEN) vector_irq[a9] = 15 (XEN) vector_irq[b1] = 16 (XEN) vector_irq[b9] = 17 (XEN) vector_irq[c1] = 18 (XEN) vector_irq[c9] = 19 (XEN) vector_irq[d1] = 20 (XEN) vector_irq[d9] = 21 (XEN) vector_irq[e1] = 22 (XEN) vector_irq[e9] = 23 (XEN) ..TIMER: vector=0x41 pin1=2 pin2=0 (XEN) Using local APIC timer interrupts. (XEN) Calibrating APIC timer for CPU0... (XEN) ..... CPU speed is 2992.5999 MHz. (XEN) ..... Bus speed is 199.5065 MHz. (XEN) ..... bus_scale = 0x0000CC4F (XEN) checking TSC synchronization across CPUs: passed. (XEN) Time init: (XEN) .... System Time: 20001255ns (XEN) .... cpu_freq: 00000000:B2605588 (XEN) .... scale: 00000001:562BB70F (XEN) .... Wall Clock: 1112802717s 200000us (XEN) PCI: PCI BIOS revision 2.10 entry at 0xfb2cc, last bus=3 (XEN) PCI: Using configuration type 1 (XEN) PCI: Probing PCI hardware (XEN) PCI: Probing PCI hardware (bus 00) (XEN) PCI: Ignoring BAR0-3 of IDE controller 00:1f.1 (XEN) Transparent bridge - PCI device 8086:244e (XEN) PCI: Using IRQ router PIIX/ICH [8086/2640] at 00:1f.0 (XEN) PCI->APIC IRQ transform: (B0,I29,P0) -> 21 (XEN) PCI->APIC IRQ transform: (B0,I29,P1) -> 22 (XEN) PCI->APIC IRQ transform: (B0,I29,P2) -> 18 (XEN) PCI->APIC IRQ transform: (B0,I29,P3) -> 23 (XEN) PCI->APIC IRQ transform: (B0,I29,P0) -> 21 (XEN) PCI->APIC IRQ transform: (B0,I30,P0) -> 23 (XEN) PCI->APIC IRQ transform: (B0,I31,P0) -> 16 (XEN) PCI->APIC IRQ transform: (B0,I31,P2) -> 20 (XEN) PCI->APIC IRQ transform: (B0,I31,P1) -> 17 (XEN) PCI->APIC IRQ transform: (B1,I0,P0) -> 16 (XEN) PCI->APIC IRQ transform: (B3,I1,P0) -> 17 (XEN) PCI: using PPB(B0,I30,P0) to get irq 23 (XEN) PCI->APIC IRQ transform: (B3,I8,P0) -> 23 (XEN) mtrr: v2.0 (20020519) (XEN) *** LOADING DOMAIN 0 *** (XEN) Xen-ELF header found: 'GUEST_OS=linux,GUEST_VER=2.6,XEN_VER=3.0,VIRT_BASE'(XEN) PHYSICAL MEMORY ARRANGEMENT: (XEN) Dom0 alloc.: 08000000->10000000 (XEN) VIRTUAL MEMORY ARRANGEMENT: (XEN) Loaded kernel: c0100000->c0478cfc (XEN) Init. ramdisk: c0479000->c078ea00 (XEN) Phys-Mach map: c078f000->c07af000 (XEN) Page tables: c07af000->c07b3000 (XEN) Start info: c07b3000->c07b4000 (XEN) Boot stack: c07b4000->c07b5000 (XEN) TOTAL: c0000000->c0c00000 (XEN) ENTRY ADDRESS: c0100000 (XEN) Initrd len 0x315a00, start at 0xc0479000 (XEN) Scrubbing Free RAM: ...........done. (XEN) *** Serial input -> DOM0 (type 'CTRL-a' three times to switch input to Xe.Linux version 2.6.11-1.1226_FC4xen0 (bhcompile@xxxxxxxxxxxxxxxxxxxxxxxxxx) (gcc5BIOS-provided physical RAM map: Xen: 0000000000000000 - 0000000008000000 (usable) 128MB LOWMEM available. Using x86 segment limits to approximate NX protection DMI 2.3 present. IRQ lockup detection disabled Allocating PCI resources starting at 08000000 (gap: 08000000:f8000000) Built 1 zonelists Kernel command line: ro root=/dev/volume_01/root console=ttyS0 Initializing CPU#0 PID hash table entries: 1024 (order: 10, 16384 bytes) Xen reported: 2992.657 MHz processor. Using tsc for high-res timesource Console: colour VGA+ 80x25 Dentry cache hash table entries: 32768 (order: 5, 131072 bytes) Inode-cache hash table entries: 16384 (order: 4, 65536 bytes) Memory: 121600k/131072k available (2321k kernel code, 9388k reserved, 687k data)Checking if this processor honours the WP bit even in supervisor mode... Ok. Security Framework v1.0.0 initialized SELinux: Initializing. SELinux: Starting in permissive mode selinux_register_security: Registering secondary module capability Capability LSM initialized as secondary Mount-cache hash table entries: 512 CPU: Trace cache: 12K uops, L1 D cache: 16K CPU: L2 cache: 1024K Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Checking 'hlt' instruction... disabled CPU0: Intel(R) Pentium(R) 4 CPU 3.00GHz stepping 04 per-CPU timeslice cutoff: 2925.83 usecs. task migration cache decay timeout: 3 msecs. Booting processor 1/1 eip c0100010 Initializing CPU#1 CPU: Trace cache: 12K uops, L1 D cache: 16K CPU: L2 cache: 1024K CPU1: Intel(R) Pentium(R) 4 CPU 3.00GHz stepping 04 Total of 2 processors activated (11953.76 BogoMIPS). Brought up 2 CPUs checking if image is initramfs... it is Freeing initrd memory: 3158k freed NET: Registered protocol family 16 PCI: Using configuration type Xen Linux Plug and Play Support v0.97 (c) Adam Belay xen_mem: Initialising balloon driver. usbcore: registered new driver usbfs usbcore: registered new driver hub PCI: Probing PCI hardware PCI: Probing PCI hardware (bus 00) PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1 PCI: Transparent bridge - 0000:00:1e.0 PCI: Probing PCI hardware (bus 01) PCI: Probing PCI hardware (bus 03) PCI: Probing PCI hardware IA-32 Microcode Update Driver: v1.14-xen <tigran@xxxxxxxxxxx> audit: initializing netlink socket (disabled) audit(1112802721.290:0): initialized Total HugeTLB memory allocated, 0 VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) SELinux: Registering netfilter hooks Initializing Cryptographic API ksign: Installing public key data Loading keyring - Added public key 7A9F2968617F8655 - User ID: Red Hat, Inc. (Kernel Module GPG key) (XEN) PCI: No IRQ known for interrupt pin A of device 00:01.0. Probably buggy M.Ti(XEN) mer ISR/1: Time went backwards: -79997000 4590000000 4000 4570000000PCI. PCI: No IRQ known for interrupt pin A of device 0000:00:01.0. pcie_portdrv_probe->Dev[2581:8086] has invalid IRQ. Check vendor BIOS assign_interrupt_mode Found MSI capability PCI: No IRQ known for interrupt pin A of device 0000:00:1c.0. pcie_portdrv_probe->Dev[2660:8086] has invalid IRQ. Check vendor BIOS assign_interrupt_mode Found MSI capability isapnp: Scanning for PnP cards... isapnp: No Plug & Play device found Real Time Clock Driver v1.12 Linux agpgart interface v0.101 (c) Dave Jones agpgart: Detected an Intel 915G Chipset. agpgart: AGP aperture is 256M @ 0x0 [drm] Initialized drm 1.0.0 20040925 PNP: No PS/2 controller found. Probing ports directly. serio: i8042 AUX port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize Xen virtual console successfully installed as ttyS0 Event-channel device installed. Initialising Xen netif backend Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx ICH6: IDE controller at PCI slot 0000:00:1f.1 PCI: Obtained IRQ 16 for device 0000:00:1f.1 ICH6: chipset revision 3 ICH6: not 100% native mode: will probe irqs later ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:DMA hda: GCR-8483B, ATAPI CD/DVD-ROM drive hdb: _NEC DVD+RW ND-3100AD, ATAPI CD/DVD-ROM drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 hda: ATAPI 48X CD-ROM drive, 128kB Cache, UDMA(33) Uniform CD-ROM driver Revision: 3.20 hdb: ATAPI 48X DVD-ROM CD-R/RW drive, 2048kB Cache, UDMA(33) ide-floppy driver 0.99.newide usbcore: registered new driver hiddev usbcore: registered new driver usbhid drivers/usb/input/hid-core.c: v2.01:USB HID core driver mice: PS/2 mouse device common for all mice md: md driver 0.90.1 MAX_MD_DEVS=256, MD_SB_DISKS=27 input: AT Translated Set 2 keyboard on isa0060/serio0 NET: Registered protocol family 2 IP: routing cache hash table of 512 buckets, 8Kbytes TCP established hash table entries: 8192 (order: 5, 131072 bytes) TCP bind hash table entries: 8192 (order: 4, 98304 bytes) TCP: Hash tables configured (established 8192 bind 8192) Initializing IPsec netlink socket NET: Registered protocol family 1 NET: Registered protocol family 17 Freeing unused kernel memory: 196k freed Red Hat nash version 4.2.1 starting Mounted /proc filesystem Mounting sysfs Creating /dev Starting udev Loading scsi_mod.ko module SCSI subsystem initialized Loading sd_mod.ko module Loading libata.ko module Loading ata_piix.ko module PCI: Obtained IRQ 20 for device 0000:00:1f.2 input: ImPS/2 Generic Wheel Mouse on isa0060/serio1 ata1: SATA max UDMA/133 cmd 0xFE00 ctl 0xFE12 bmdma 0xFEA0 irq 20 ata2: SATA max UDMA/133 cmd 0xFE20 ctl 0xFE32 bmdma 0xFEA8 irq 20 ata1: dev 0 ATA, max UDMA/133, 312500000 sectors: lba48 ata1: dev 0 configured for UDMA/133 scsi0 : ata_piix ATA: abnormal status 0xFF on port 0xFE27 ata2: disabling port scsi1 : ata_piix Vendor: ATA Model: WDC WD1600JD-75H Rev: 08.0 Type: Direct-Access ANSI SCSI revision: 05 SCSI device sda: 312500000 512-byte hdwr sectors (160000 MB) SCSI device sda: drive cache: write back SCSI device sda: 312500000 512-byte hdwr sectors (160000 MB) SCSI device sda: drive cache: write back sda: sda1 sda2 Attached scsi disk sda at scsi0, channel 0, id 0, lun 0 Loading dm-mod.ko module device-mapper: 4.4.0-ioctl (2005-01-12) initialised: dm-devel@xxxxxxxxxx Loading jbd.ko module Loading ext3.ko module Loading dm-mirror.ko module Loading dm-zero.ko module Loading dm-snapshot.ko module Making device-mapper control node Scanning logical volumes File descriptor 3 left open Reading all physical volumes. This may take a while... cdrom: open failed. cdrom: open failed. Found volume group "volume_01" using metadata type lvm2 Activating logical volumes File descriptor 3 left open 7 logical volume(s) in volume group "volume_01" now active Making device nodes File descriptor 3 left open Creating root device Mounting root filesystem kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. Switching to new root *************************************************************** *************************************************************** ** WARNING: Currently emulating unsupported memory accesses ** ** in /lib/tls libraries. The emulation is very ** ** slow, and may not work correctly with all ** ** programs (e.g., some may 'Segmentation fault'). ** ** TO ENSURE FULL PERFORMANCE AND CORRECT FUNCTION, ** ** YOU MUST EXECUTE THE FOLLOWING AS ROOT: ** ** mv /lib/tls /lib/tls.disabled ** *************************************************************** *************************************************************** Continuing... security: 3 users, 5 roles, 589 types, 61 bools security: 54 classes, 71803 rules SELinux: Completing initialization. SELinux: Setting up existing superblocks. SELinux: initialized (dev dm-0, type ext3), uses xattr SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs SELinux: initialized (dev selinuxfs, type selinuxfs), uses genfs_contexts SELinux: initialized (dev mqueue, type mqueue), not configured for labeling SELinux: initialized (dev hugetlbfs, type hugetlbfs), not configured for labeligSELinux: initialized (dev devpts, type devpts), uses transition SIDs SELinux: initialized (dev eventpollfs, type eventpollfs), uses genfs_contexts SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs SELinux: initialized (dev futexfs, type futexfs), uses genfs_contexts SELinux: initialized (dev pipefs, type pipefs), uses task SIDs SELinux: initialized (dev sockfs, type sockfs), uses task SIDs SELinux: initialized (dev cpuset, type cpuset), not configured for labeling SELinux: initialized (dev proc, type proc), uses genfs_contexts SELinux: initialized (dev bdev, type bdev), uses genfs_contexts SELinux: initialized (dev rootfs, type rootfs), uses genfs_contexts SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts INIT: version 2.85 booting SELinux: initialized (dev usbfs, type usbfs), uses genfs_contexts Welcome to Fedora Core Press 'I' to enter interactive startup. Starting udev: [ OK ] Initializing hardware... storage network audio done[ OK ] Setting clock (utc): Wed Apr 6 16:52:30 BST 2005 [ OK ] Setting hostname animal.passback.co.uk: [ OK ] Setting up Logical Volume Management: File descriptor 3 left open /var/lock: mkdir failed: Read-only file system 7 logical volume(s) in volume group "volume_01" now active [ OK ] Checking filesystems Checking all file systems. [/sbin/fsck.ext3 (1) -- /] fsck.ext3 -a /dev/volume_01/root /dev/volume_01/root: clean, 18128/262144 files, 133030/262144 blocks [/sbin/fsck.ext3 (1) -- /boot] fsck.ext3 -a /dev/sda1 /boot: clean, 65/263232 files, 24437/263056 blocks [/sbin/fsck.ext3 (1) -- /export/backup] fsck.ext3 -a /dev/volume_01/backup /dev/volume_01/backup: clean, 377040/10485760 files, 7569225/10485760 blocks [/sbin/fsck.ext3 (1) -- /export/animal] fsck.ext3 -a /dev/volume_01/animal /dev/volume_01/animal: clean, 17/5242880 files, 726262/10485760 blocks [/sbin/fsck.ext3 (1) -- /tmp] fsck.ext3 -a /dev/volume_01/tmp /dev/volume_01/tmp: clean, 541/262144 files, 34039/262144 blocks [/sbin/fsck.ext3 (1) -- /usr] fsck.ext3 -a /dev/volume_01/usr /dev/volume_01/usr: clean, 324735/5242880 files, 1768974/5242880 blocks [/sbin/fsck.ext3 (1) -- /var] fsck.ext3 -a /dev/volume_01/var /dev/volume_01/var: clean, 5263/1048576 files, 375637/1048576 blocks [ OK ] Remounting root filesystem in read-write mode: [ OK ] Mounting local filesystems: [ OK ] Enabling local filesystem quotas: [ OK ] Enabling swap space: [ OK ] INIT: Entering runlevel: 5 Entering non-interactive startup Starting sysstat: Calling the system activity data collector (sadc): [ OK ] Starting readahead_early: Starting background readahead: [ OK ] Bringing up loopback interface: [ OK ] Bringing up interface eth0: [ OK ] Starting system logger: [ OK ] Starting kernel logger: [ OK ] Starting irqbalance: [ OK ] Starting portmap: [ OK ] Starting NFS statd: [ OK ] Starting auditd: [ OK ] Starting RPC idmapd: [ OK ] Mounting other filesystems: [ OK ] Starting lm_sensors: [ OK ] Starting automount: [ OK ] Starting nifd... Starting mDNSResponder... [ OK ] Starting cups: [ OK ] Starting sshd: [ OK ] ip_tables: (C) 2000-2002 Netfilter core team Starting xinetd: [ OK ] ntpd: Synchronizing with time server: Debug: sleeping function called from inva0in_atomic():1, irqs_disabled():0 [<c01534a4>] __kmalloc+0x174/0x190 [<c8867cce>] ata_interrupt+0xce/0x120 [libata] [<c01a8885>] proc_create+0xb5/0x130 [<c01a89ef>] proc_mkdir_mode+0x2f/0x70 [<c01a8a50>] proc_mkdir+0x20/0x30 [<c0147d85>] register_handler_proc+0xc5/0xf0 [<c01473be>] setup_irq+0xae/0x110 [<c8945870>] e100_intr+0x0/0x1a0 [e100] [<c01476ba>] request_irq+0xaa/0xd0 [<c8946865>] e100_up+0x125/0x250 [e100] [<c8945870>] e100_intr+0x0/0x1a0 [e100] [<c02e6880>] dev_watchdog+0x0/0xd0 [<c02e6943>] dev_watchdog+0xc3/0xd0 [<c0129f5e>] run_timer_softirq+0xee/0x1f0 [<c0125204>] __do_softirq+0x84/0x110 [<c0125309>] do_softirq+0x79/0x80 [<c010e8c2>] do_IRQ+0x22/0x30 [<c0106372>] evtchn_do_upcall+0x82/0xb0 [<c010a441>] hypervisor_callback+0x31/0x3c [<c0107dce>] xen_idle+0x7e/0x160 [<c0107ef1>] cpu_idle+0x41/0x60 [FAILED] Starting ntpd: [ OK ] Starting sendmail: Debug: sleeping function called from invalid context at mm/s0in_atomic():1, irqs_disabled():0 [<c01534a4>] __kmalloc+0x174/0x190 [<c01a8885>] proc_create+0xb5/0x130 [<c01a89ef>] proc_mkdir_mode+0x2f/0x70 [<c01a8a50>] proc_mkdir+0x20/0x30 [<c0147d85>] register_handler_proc+0xc5/0xf0 [<c01473be>] setup_irq+0xae/0x110 [<c8945870>] e100_intr+0x0/0x1a0 [e100] [<c01476ba>] request_irq+0xaa/0xd0 [<c8946865>] e100_up+0x125/0x250 [e100] [<c8945870>] e100_intr+0x0/0x1a0 [e100] [<c02e6880>] dev_watchdog+0x0/0xd0 [<c02e6943>] dev_watchdog+0xc3/0xd0 [<c0129f5e>] run_timer_softirq+0xee/0x1f0 [<c0125204>] __do_softirq+0x84/0x110 [<c0125309>] do_softirq+0x79/0x80 [<c010e8c2>] do_IRQ+0x22/0x30 [<c0106372>] evtchn_do_upcall+0x82/0xb0 [<c010a441>] hypervisor_callback+0x31/0x3c [<c0107dce>] xen_idle+0x7e/0x160 [<c0107ef1>] cpu_idle+0x41/0x60 [ OK ] Starting sm-client: Debug: sleeping function called from invalid context at mm/0in_atomic():1, irqs_disabled():0 [<c01534a4>] __kmalloc+0x174/0x190 [<c8867cce>] ata_interrupt+0xce/0x120 [libata] [<c01a8885>] proc_create+0xb5/0x130 [<c01a89ef>] proc_mkdir_mode+0x2f/0x70 [<c01a8a50>] proc_mkdir+0x20/0x30 [<c0147d85>] register_handler_proc+0xc5/0xf0 [<c01473be>] setup_irq+0xae/0x110 [<c8945870>] e100_intr+0x0/0x1a0 [e100] [<c01476ba>] request_irq+0xaa/0xd0 [<c8946865>] e100_up+0x125/0x250 [e100] [<c8945870>] e100_intr+0x0/0x1a0 [e100] [<c02e6880>] dev_watchdog+0x0/0xd0 [<c02e6943>] dev_watchdog+0xc3/0xd0 [<c0129f5e>] run_timer_softirq+0xee/0x1f0 [<c0125204>] __do_softirq+0x84/0x110 [<c0125309>] do_softirq+0x79/0x80 [<c010e8c2>] do_IRQ+0x22/0x30 [<c0106372>] evtchn_do_upcall+0x82/0xb0 [<c010a441>] hypervisor_callback+0x31/0x3c [<c0107dce>] xen_idle+0x7e/0x160 [<c0107ef1>] cpu_idle+0x41/0x60 [ OK ] Starting crond: [ OK ] Starting xfs: [ OK ] Starting anacron: [ OK ] Starting atd: [ OK ] Starting readahead: Starting background readahead: [ OK ] Starting system message bus: [ OK ] Starting cups-config-daemon: [ OK ] Starting HAL daemon: [ OK ] Debug: sleeping function called from invalid context at mm/slab.c:2090 in_atomic():1, irqs_disabled():0 [<c01534a4>] __kmalloc+0x174/0x190 [<c01a8885>] proc_create+0xb5/0x130 [<c0118688>] try_to_wake_up+0x98/0x330 [<c01a89ef>] proc_mkdir_mode+0x2f/0x70 [<c01a8a50>] proc_mkdir+0x20/0x30 [<c0147d85>] register_handler_proc+0xc5/0xf0 [<c01473be>] setup_irq+0xae/0x110 [<c8945870>] e100_intr+0x0/0x1a0 [e100] [<c01476ba>] request_irq+0xaa/0xd0 [<c8946865>] e100_up+0x125/0x250 [e100] [<c8945870>] e100_intr+0x0/0x1a0 [e100] [<c02e6880>] dev_watchdog+0x0/0xd0 [<c02e6943>] dev_watchdog+0xc3/0xd0 [<c0129f5e>] run_timer_softirq+0xee/0x1f0 [<c0125204>] __do_softirq+0x84/0x110 [<c0125309>] do_softirq+0x79/0x80 [<c010e8c2>] do_IRQ+0x22/0x30 [<c0106372>] evtchn_do_upcall+0x82/0xb0 [<c010a441>] hypervisor_callback+0x31/0x3c [<c0107dce>] xen_idle+0x7e/0x160 [<c0107ef1>] cpu_idle+0x41/0x60
# grub.conf generated by anaconda # # Note that you do not have to rerun grub after making changes to this file # NOTICE: You have a /boot partition. This means that # all kernel and initrd paths are relative to /boot/, eg. # root (hd0,0) # kernel /vmlinuz-version ro root=/dev/volume_01/root # initrd /initrd-version.img #boot=/dev/sda default=1 timeout=5 splashimage=(hd0,0)/grub/splash.xpm.gz hiddenmenu title Fedora Core (2.6.11-1.1226_FC4xen0) root (hd0,0) kernel /xen.gz dom0_mem=131072 com1=9600,8n1 console=com1 module /vmlinuz-2.6.11-1.1226_FC4xen0 ro root=/dev/volume_01/root console=ttyS0 module /initrd-2.6.11-1.1226_FC4xen0.img title Fedora Core (2.6.11-1.1226_FC4smp) root (hd0,0) kernel /vmlinuz-2.6.11-1.1226_FC4smp ro root=/dev/volume_01/root rhgb quiet initrd /initrd-2.6.11-1.1226_FC4smp.img title Fedora Core (2.6.11-1.1226_FC4) Single root (hd0,0) kernel /vmlinuz-2.6.11-1.1226_FC4 ro root=/dev/volume_01/root single initrd /initrd-2.6.11-1.1226_FC4.img