> ons, 16.03.2005 kl. 15.31 skrev Eric Tanguy: >> > Le mardi 15 mars 2005 à 06:38 -0500, Bob Chiodini a écrit : >> >> On Mon, 2005-03-14 at 23:50 +0100, Eric Tanguy wrote: >> >> > i tried a lot of thing to solve my problem and maybe it could be a >> >> > module problem : >> >> > modprobing bttv seems to give good results and all is autodetected >> >> (the >> >> > tuner seems to be the right one) : >> >> > bttv: driver version 0.9.15 loaded >> >> > bttv: using 8 buffers with 2080k (520 pages) each for capture >> >> > bttv: Bt8xx card found (0). >> >> > ACPI: PCI interrupt 0000:01:07.0[A] -> GSI 11 (level, low) -> IRQ >> 11 >> >> > bttv0: Bt878 (rev 17) at 0000:01:07.0, irq: 11, latency: 64, mmio: >> >> > 0xeb800000 >> >> > bttv0: detected: Pinnacle PCTV [card=39], PCI subsystem ID is >> >> 11bd:0012 >> >> > bttv0: using: Pinnacle PCTV Studio/Rave [card=39,autodetected] >> >> > bttv0: gpio: en=00000000, out=00000000 in=00fff3ff [init] >> >> > bttv0: i2c: checking for MSP34xx @ 0x80... not found >> >> > bttv0: pinnacle/mt: id=4 info="PAL+SECAM / mono" radio=no >> >> > bttv0: using tuner=33 >> >> > bttv0: i2c: checking for MSP34xx @ 0x80... not found >> >> > bttv0: i2c: checking for TDA9875 @ 0xb0... not found >> >> > bttv0: i2c: checking for TDA7432 @ 0x8a... not found >> >> > tda9885/6/7: chip found @ 0x96 >> >> > tuner: chip found at addr 0xc0 i2c-bus bt878 #0 [sw] >> >> > tuner: type set to 33 (MT20xx universal) by bt878 #0 [sw] >> >> > tuner: microtune: companycode=3cbf part=42 rev=2f >> >> > tuner: microtune MT2050 found, OK >> >> > bttv0: registered device video0 >> >> > bttv0: registered device vbi0 >> >> > bttv0: PLL: 28636363 => 35468950 . ok >> >> > >> >> > The problem is i receive no signal in tvtime whereas this card >> works >> >> > fine under windows. It seems the system cannot set the right tuner >> >> > frequency : >> >> > >> >> > mt2050_set_if_freq failed with -121 >> >> > >> >> > Someone could help me ? >> >> >> >> Eric, >> >> >> >> Take a look at this thread. >> >> >> >> http://groups-beta.google.com/group/linux.kernel/browse_thread/thread/58bd50364a5b47d8/81b8dfdd7bed9d95?q=linux+Pinnacle+PCTV+rave+tuner#81b8dfdd7bed9d95 >> >> >> >> It looks like there is a patch. Also, one of the posters said it >> worked >> >> in 2.6.9. Do you have a 2.6.9 version of the kernel still around? >> >> >> >> BTW: I don't see why your question was off-topic on the "other >> list". >> >> >> >> Bob... >> >> >> > Yes you are right. I try the old 2.6.9-1.667 kernel instead of the >> > actual 2.6.10-1.770_FC3 one and my tv tuner works fine. >> > So it would be a kernel module problem and if i can't ask this kind of >> > questions on the devel list i don't where i can ... >> > Thanks >> > Eric >> > >> > >> No answer ? What can i do ?? >> Eric > > Bugzilla it? > > Yes but where because i'm a newbie : kernel ? FC3 ? bttv ? ... Maybe the problem is solved in 2.6.11 kernel ? Is it safe to try the 2.6.11 FC4 kernel from the devel tree on FC3 ? Thanks Eric
