Hi list, I'm looking for advice/help in tracking down a problem with a new system I've purchased. I have a beige box server with a Gigabyte GA-M51GM-S2G motherboard. It has the nVidia MCP51 SATA controller with 3 250 gig Western Digital hard drives attached to it. It seems that when doing a considerable amount of file writing, the filesystem will become read-only. See attached dmesg output. I started looking for help on the nvnews forums, and found a suggestion to set the pci=nommconf kernel parameter. This did not help. Aside from that, there have only been suggestions such as "its likely faulty hardware". kernel 2.6.17-10-generic #2 SMP running on Ubuntu Edgy Eft, amd64 version; but the same problem showed up on Fedora Core 6, both x86_64 and i386. I checked to see if it was perhaps bad memory by running memtest86+, but after 14 hours no errors were found. I've run badblocks on the disk that contains the ext3 partition and no errors were found. Aside from badblocks, I'm not aware of any disk tools I could use to test further. smartmon tools report that all 3 of the disks are OK. The bulk of the data being sent to the machine is via the network using the application Unison, version 2.13.16 if that makes any difference. I haven't tried another suggestion to set the kernel paramter idle=poll, but since nothing else has worked so far, I don't see that making much difference. Also I haven't tried installing Windows to isolate the "faulty hardware" suggestion. Bad hardware would suggest that Windows would see problems too right? Any help would be greatly appreciated. I'm at the end of my rope on this one. Thanks in advance, Tim
[ 0.000000] Bootdata ok (command line is root=/dev/sda1 ro quiet splash) [ 0.000000] Linux version 2.6.17-10-generic (root@king) (gcc version 4.1.2 20060928 (prerelease) (Ubuntu 4.1.1-13ubuntu5)) #2 SMP Tue Dec 5 21:16:35 UTC 2006 (Ubuntu 2.6.17-10.34-generic) [ 0.000000] BIOS-provided physical RAM map: [ 0.000000] BIOS-e820: 0000000000000000 - 000000000009f800 (usable) [ 0.000000] BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved) [ 0.000000] BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) [ 0.000000] BIOS-e820: 0000000000100000 - 000000007bff0000 (usable) [ 0.000000] BIOS-e820: 000000007bff0000 - 000000007bff3000 (ACPI NVS) [ 0.000000] BIOS-e820: 000000007bff3000 - 000000007c000000 (ACPI data) [ 0.000000] BIOS-e820: 000000007c000000 - 0000000080000000 (reserved) [ 0.000000] BIOS-e820: 00000000f0000000 - 00000000f2000000 (reserved) [ 0.000000] BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved) [ 0.000000] DMI 2.3 present. [ 0.000000] ACPI: RSDP (v000 GBT ) @ 0x00000000000f6bf0 [ 0.000000] ACPI: RSDT (v001 GBT AWRDACPI 0x42302e31 AWRD 0x01010101) @ 0x000000007bff3000 [ 0.000000] ACPI: FADT (v001 GBT AWRDACPI 0x42302e31 AWRD 0x01010101) @ 0x000000007bff3040 [ 0.000000] ACPI: SSDT (v001 PTLTD POWERNOW 0x00000001 LTP 0x00000001) @ 0x000000007bff7a40 [ 0.000000] ACPI: MCFG (v001 GBT AWRDACPI 0x42302e31 AWRD 0x01010101) @ 0x000000007bff7b80 [ 0.000000] ACPI: MADT (v001 GBT AWRDACPI 0x42302e31 AWRD 0x01010101) @ 0x000000007bff79c0 [ 0.000000] ACPI: DSDT (v001 GBT AWRDACPI 0x00001000 MSFT 0x0100000c) @ 0x0000000000000000 [ 0.000000] Scanning NUMA topology in Northbridge 24 [ 0.000000] Number of nodes 1 [ 0.000000] Node 0 MemBase 0000000000000000 Limit 000000007bff0000 [ 0.000000] NUMA: Using 63 for the hash shift. [ 0.000000] Using node hash shift of 63 [ 0.000000] Bootmem setup node 0 0000000000000000-000000007bff0000 [ 0.000000] On node 0 totalpages: 499496 [ 0.000000] DMA zone: 2591 pages, LIFO batch:0 [ 0.000000] DMA32 zone: 496905 pages, LIFO batch:31 [ 0.000000] Nvidia board detected. Ignoring ACPI timer override. [ 0.000000] ACPI: PM-Timer IO Port: 0x1008 [ 0.000000] ACPI: Local APIC address 0xfee00000 [ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) [ 0.000000] Processor #0 15:15 APIC version 16 [ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] disabled) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] dfl dfl lint[0x1]) [ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] dfl dfl lint[0x1]) [ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0]) [ 0.000000] IOAPIC[0]: apic_id 2, version 17, address 0xfec00000, GSI 0-23 [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 14 global_irq 14 high edge) [ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 15 global_irq 15 high edge) [ 0.000000] ACPI: IRQ9 used by override. [ 0.000000] ACPI: IRQ14 used by override. [ 0.000000] ACPI: IRQ15 used by override. [ 0.000000] Setting APIC routing to physical flat [ 0.000000] Using ACPI (MADT) for SMP configuration information [ 0.000000] Allocating PCI resources starting at 88000000 (gap: 80000000:70000000) [ 0.000000] Checking aperture... [ 0.000000] CPU 0: aperture @ 8d2000000 size 32 MB [ 0.000000] Aperture from northbridge cpu 0 too small (32 MB) [ 0.000000] No AGP bridge found [ 0.000000] SMP: Allowing 2 CPUs, 1 hotplug CPUs [ 0.000000] Built 1 zonelists [ 0.000000] Kernel command line: root=/dev/sda1 ro quiet splash [ 0.000000] Initializing CPU#0 [ 0.000000] PID hash table entries: 4096 (order: 12, 32768 bytes) [ 0.000000] time.c: Using 3.579545 MHz WALL PM GTOD PIT/TSC timer. [ 0.000000] time.c: Detected 2210.099 MHz processor. [ 31.496149] Console: colour VGA+ 80x25 [ 31.497187] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes) [ 31.498828] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes) [ 31.517245] Memory: 1988984k/2031552k available (2129k kernel code, 42180k reserved, 1424k data, 188k init) [ 31.595282] Calibrating delay using timer specific routine.. 4423.97 BogoMIPS (lpj=8847954) [ 31.595331] Security Framework v1.0.0 initialized [ 31.595338] SELinux: Disabled at boot. [ 31.595358] Mount-cache hash table entries: 256 [ 31.595487] CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) [ 31.595490] CPU: L2 Cache: 512K (64 bytes/line) [ 31.595493] CPU 0/0(1) -> Node 0 -> Core 0 [ 31.595509] SMP alternatives: switching to UP code [ 31.595732] checking if image is initramfs... it is [ 32.041938] Freeing initrd memory: 5746k freed [ 32.045044] ACPI: Core revision 20060707 [ 32.048253] ACPI: Looking for DSDT ... not found! [ 32.092416] Using local APIC timer interrupts. [ 32.137634] result 12557381 [ 32.137635] Detected 12.557 MHz APIC timer. [ 32.138968] Brought up 1 CPUs [ 32.139010] testing NMI watchdog ... OK. [ 32.179051] migration_cost=0 [ 32.179272] NET: Registered protocol family 16 [ 32.179296] ACPI: bus type pci registered [ 32.182375] PCI: Using MMCONFIG at f0000000 [ 32.182403] PCI: No mmconfig possible on device 0:18 [ 32.189811] ACPI: Interpreter enabled [ 32.189813] ACPI: Using IOAPIC for interrupt routing [ 32.190245] ACPI: PCI Root Bridge [PCI0] (0000:00) [ 32.190248] PCI: Probing PCI hardware (bus 00) [ 32.193809] Boot video device is 0000:00:05.0 [ 32.194098] PCI: Ignoring BAR0-3 of IDE controller 0000:00:0d.0 [ 32.194587] PCI: Transparent bridge - 0000:00:10.0 [ 32.194615] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] [ 32.291383] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT] [ 32.292777] ACPI: PCI Interrupt Link [LNK1] (IRQs *5 7 9 10 11 14 15) [ 32.293059] ACPI: PCI Interrupt Link [LNK2] (IRQs 5 7 9 10 11 14 15) *0, disabled. [ 32.293342] ACPI: PCI Interrupt Link [LNK3] (IRQs 5 7 9 10 *11 14 15) [ 32.293627] ACPI: PCI Interrupt Link [LNK4] (IRQs 5 7 9 10 11 14 15) *0, disabled. [ 32.293909] ACPI: PCI Interrupt Link [LNK5] (IRQs 5 7 9 10 11 14 15) *0, disabled. [ 32.294191] ACPI: PCI Interrupt Link [LNK6] (IRQs 5 7 9 10 11 14 15) *0, disabled. [ 32.294475] ACPI: PCI Interrupt Link [LNK7] (IRQs 5 7 9 *10 11 14 15) [ 32.294756] ACPI: PCI Interrupt Link [LNK8] (IRQs 5 7 9 10 11 14 15) *0, disabled. [ 32.295054] ACPI: PCI Interrupt Link [LUBA] (IRQs 5 7 9 *10 11 14 15) [ 32.295335] ACPI: PCI Interrupt Link [LUBB] (IRQs 5 7 9 10 11 14 15) *0, disabled. [ 32.295622] ACPI: PCI Interrupt Link [LMAC] (IRQs 5 7 9 10 *11 14 15) [ 32.295903] ACPI: PCI Interrupt Link [LACI] (IRQs 5 7 9 10 11 14 15) *0, disabled. [ 32.296188] ACPI: PCI Interrupt Link [LAZA] (IRQs *5 7 9 10 11 14 15) [ 32.296469] ACPI: PCI Interrupt Link [LPMU] (IRQs 5 7 9 10 11 14 15) *0, disabled. [ 32.296751] ACPI: PCI Interrupt Link [LMCI] (IRQs 5 7 9 10 11 14 15) *0, disabled. [ 32.297036] ACPI: PCI Interrupt Link [LSMB] (IRQs 5 7 9 10 *11 14 15) [ 32.297319] ACPI: PCI Interrupt Link [LUB2] (IRQs *5 7 9 10 11 14 15) [ 32.297604] ACPI: PCI Interrupt Link [LIDE] (IRQs 5 7 9 10 11 14 15) *0, disabled. [ 32.297887] ACPI: PCI Interrupt Link [LSID] (IRQs 5 7 9 10 *11 14 15) [ 32.298169] ACPI: PCI Interrupt Link [LFID] (IRQs 5 7 9 *10 11 14 15) [ 32.298535] ACPI: PCI Interrupt Link [APC1] (IRQs 16) *0, disabled. [ 32.298892] ACPI: PCI Interrupt Link [APC2] (IRQs 17) *0, disabled. [ 32.299246] ACPI: PCI Interrupt Link [APC3] (IRQs 18) *0, disabled. [ 32.299597] ACPI: PCI Interrupt Link [APC4] (IRQs 19) *0, disabled. [ 32.299954] ACPI: PCI Interrupt Link [APC5] (IRQs 16) *0, disabled. [ 32.300309] ACPI: PCI Interrupt Link [APC6] (IRQs 16) *0, disabled. [ 32.300662] ACPI: PCI Interrupt Link [APC7] (IRQs 16) *0, disabled. [ 32.301014] ACPI: PCI Interrupt Link [APC8] (IRQs 16) *0, disabled. [ 32.301369] ACPI: PCI Interrupt Link [APCF] (IRQs 20 21 22 23) *0, disabled. [ 32.301724] ACPI: PCI Interrupt Link [APCG] (IRQs 20 21 22 23) *0, disabled. [ 32.302079] ACPI: PCI Interrupt Link [APCH] (IRQs 20 21 22 23) *0, disabled. [ 32.302436] ACPI: PCI Interrupt Link [APCJ] (IRQs 20 21 22 23) *0, disabled. [ 32.302792] ACPI: PCI Interrupt Link [APMU] (IRQs 20 21 22 23) *0, disabled. [ 32.303175] ACPI: PCI Interrupt Link [AAZA] (IRQs 20 21 22 23) *0, disabled. [ 32.303529] ACPI: PCI Interrupt Link [APCK] (IRQs 20 21 22 23) *0, disabled. [ 32.303882] ACPI: PCI Interrupt Link [APCS] (IRQs 20 21 22 23) *0, disabled. [ 32.304236] ACPI: PCI Interrupt Link [APCL] (IRQs 20 21 22 23) *0, disabled. [ 32.304589] ACPI: PCI Interrupt Link [APCM] (IRQs 20 21 22 23) *0, disabled. [ 32.304948] ACPI: PCI Interrupt Link [APCZ] (IRQs 20 21 22 23) *0, disabled. [ 32.305302] ACPI: PCI Interrupt Link [APSI] (IRQs 20 21 22 23) *0, disabled. [ 32.305656] ACPI: PCI Interrupt Link [APSJ] (IRQs 20 21 22 23) *0, disabled. [ 32.308209] Linux Plug and Play Support v0.97 (c) Adam Belay [ 32.308219] pnp: PnP ACPI init [ 32.313551] pnp: PnP ACPI: found 14 devices [ 32.313600] PCI: Using ACPI for IRQ routing [ 32.313605] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report [ 32.313770] PCI-DMA: Disabling IOMMU. [ 32.314302] pnp: 00:01: ioport range 0x1000-0x107f could not be reserved [ 32.314305] pnp: 00:01: ioport range 0x1080-0x10ff has been reserved [ 32.314307] pnp: 00:01: ioport range 0x1400-0x147f has been reserved [ 32.314310] pnp: 00:01: ioport range 0x1480-0x14ff could not be reserved [ 32.314312] pnp: 00:01: ioport range 0x1800-0x187f has been reserved [ 32.314315] pnp: 00:01: ioport range 0x1880-0x18ff has been reserved [ 32.314319] pnp: 00:01: ioport range 0x2000-0x207f has been reserved [ 32.314322] pnp: 00:01: ioport range 0x2080-0x20ff has been reserved [ 32.314488] PCI: Bridge: 0000:00:02.0 [ 32.314490] IO window: 7000-7fff [ 32.314493] MEM window: disabled. [ 32.314494] PREFETCH window: disabled. [ 32.314496] PCI: Bridge: 0000:00:03.0 [ 32.314498] IO window: 8000-8fff [ 32.314500] MEM window: disabled. [ 32.314501] PREFETCH window: disabled. [ 32.314503] PCI: Bridge: 0000:00:04.0 [ 32.314505] IO window: 9000-9fff [ 32.314507] MEM window: disabled. [ 32.314508] PREFETCH window: disabled. [ 32.314510] PCI: Bridge: 0000:00:10.0 [ 32.314512] IO window: a000-afff [ 32.314515] MEM window: f5000000-f50fffff [ 32.314518] PREFETCH window: disabled. [ 32.314527] PCI: Setting latency timer of device 0000:00:02.0 to 64 [ 32.314531] PCI: Setting latency timer of device 0000:00:03.0 to 64 [ 32.314535] PCI: Setting latency timer of device 0000:00:04.0 to 64 [ 32.314541] PCI: Setting latency timer of device 0000:00:10.0 to 64 [ 32.314596] NET: Registered protocol family 2 [ 32.350829] IP route cache hash table entries: 65536 (order: 7, 524288 bytes) [ 32.351182] TCP established hash table entries: 262144 (order: 10, 4194304 bytes) [ 32.353471] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) [ 32.354075] TCP: Hash tables configured (established 262144 bind 65536) [ 32.354079] TCP reno registered [ 32.354429] IA32 emulation $Id: sys_ia32.c,v 1.32 2002/03/24 13:02:28 ak Exp $ [ 32.354729] audit: initializing netlink socket (disabled) [ 32.354739] audit(1170009009.860:1): initialized [ 32.354886] VFS: Disk quotas dquot_6.5.1 [ 32.354906] Dquot-cache hash table entries: 512 (order 0, 4096 bytes) [ 32.354950] Initializing Cryptographic API [ 32.354954] io scheduler noop registered [ 32.354960] io scheduler anticipatory registered [ 32.354969] io scheduler deadline registered [ 32.354983] io scheduler cfq registered (default) [ 32.355376] PCI: Setting latency timer of device 0000:00:02.0 to 64 [ 32.355380] pcie_portdrv_probe->Dev[02fc:10de] has invalid IRQ. Check vendor BIOS [ 32.355393] assign_interrupt_mode Found MSI capability [ 32.355423] Allocate Port Service[0000:00:02.0:pcie00] [ 32.355452] Allocate Port Service[0000:00:02.0:pcie03] [ 32.355481] PCI: Setting latency timer of device 0000:00:03.0 to 64 [ 32.355483] pcie_portdrv_probe->Dev[02fd:10de] has invalid IRQ. Check vendor BIOS [ 32.355496] assign_interrupt_mode Found MSI capability [ 32.355511] Allocate Port Service[0000:00:03.0:pcie00] [ 32.355536] Allocate Port Service[0000:00:03.0:pcie03] [ 32.355563] PCI: Setting latency timer of device 0000:00:04.0 to 64 [ 32.355565] pcie_portdrv_probe->Dev[02fb:10de] has invalid IRQ. Check vendor BIOS [ 32.355578] assign_interrupt_mode Found MSI capability [ 32.355592] Allocate Port Service[0000:00:04.0:pcie00] [ 32.355616] Allocate Port Service[0000:00:04.0:pcie03] [ 32.373063] Real Time Clock Driver v1.12ac [ 32.373102] Linux agpgart interface v0.101 (c) Dave Jones [ 32.373105] Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled [ 32.373229] serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 32.373375] serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A [ 32.373784] 00:08: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A [ 32.373973] 00:09: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A [ 32.374138] mice: PS/2 mouse device common for all mice [ 32.374576] RAMDISK driver initialized: 16 RAM disks of 65536K size 1024 blocksize [ 32.374803] Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 [ 32.374807] ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx [ 32.374982] PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:PS2M] at 0x60,0x64 irq 1,12 [ 32.936227] serio: i8042 AUX port at 0x60,0x64 irq 12 [ 32.937678] serio: i8042 KBD port at 0x60,0x64 irq 1 [ 32.937902] TCP bic registered [ 32.937909] NET: Registered protocol family 1 [ 32.937915] NET: Registered protocol family 8 [ 32.937917] NET: Registered protocol family 20 [ 32.945834] ACPI: (supports S0 S1 S4 S5) [ 32.945878] drivers/rtc/hctosys.c: unable to open rtc device (rtc0) [ 32.945896] Freeing unused kernel memory: 188k freed [ 32.985428] input: AT Translated Set 2 keyboard as /class/input/input0 [ 33.020671] vga16fb: initializing [ 33.020676] vga16fb: mapped to 0xffff8100000a0000 [ 33.207393] Console: switching to colour frame buffer device 80x25 [ 33.207398] fb0: VGA16 VGA frame buffer device [ 34.338993] Capability LSM initialized [ 34.367669] ACPI Exception (acpi_processor-0693): AE_NOT_FOUND, Processor Device is not present [20060707] [ 34.367675] ACPI: Getting cpuindex for acpiid 0x1 [ 34.701741] SCSI subsystem initialized [ 34.704902] libata version 1.20 loaded. [ 34.705866] sata_nv 0000:00:0e.0: version 0.8 [ 34.706290] ACPI: PCI Interrupt Link [APSI] enabled at IRQ 23 [ 34.706295] GSI 16 sharing vector 0xD1 and IRQ 16 [ 34.706298] ACPI: PCI Interrupt 0000:00:0e.0[A] -> Link [APSI] -> GSI 23 (level, low) -> IRQ 209 [ 34.706386] PCI: Setting latency timer of device 0000:00:0e.0 to 64 [ 34.706460] ata1: SATA max UDMA/133 cmd 0x9F0 ctl 0xBF2 bmdma 0xD800 irq 209 [ 34.706478] ata2: SATA max UDMA/133 cmd 0x970 ctl 0xB72 bmdma 0xD808 irq 209 [ 34.912941] ata1: SATA link up 3.0 Gbps (SStatus 123) [ 35.080974] ata1: dev 0 cfg 49:2f00 82:746b 83:7f61 84:4063 85:7469 86:3c41 87:4063 88:407f [ 35.080978] ata1: dev 0 ATA-7, max UDMA/133, 490232639 sectors: LBA48 [ 35.092963] ata1: dev 0 configured for UDMA/133 [ 35.092966] scsi0 : sata_nv [ 35.300660] ata2: SATA link up 3.0 Gbps (SStatus 123) [ 35.468701] ata2: dev 0 cfg 49:2f00 82:746b 83:7f61 84:4063 85:7469 86:3c41 87:4063 88:407f [ 35.468704] ata2: dev 0 ATA-7, max UDMA/133, 490234752 sectors: LBA48 [ 35.480688] ata2: dev 0 configured for UDMA/133 [ 35.480691] scsi1 : sata_nv [ 35.481296] Vendor: ATA Model: WDC WD2500YS-01S Rev: 20.0 [ 35.481304] Type: Direct-Access ANSI SCSI revision: 05 [ 35.486596] Vendor: ATA Model: WDC WD2500YS-01S Rev: 20.0 [ 35.486605] Type: Direct-Access ANSI SCSI revision: 05 [ 35.487102] ACPI: PCI Interrupt Link [APSJ] enabled at IRQ 22 [ 35.487107] GSI 17 sharing vector 0xD9 and IRQ 17 [ 35.487111] ACPI: PCI Interrupt 0000:00:0f.0[A] -> Link [APSJ] -> GSI 22 (level, low) -> IRQ 217 [ 35.487200] PCI: Setting latency timer of device 0000:00:0f.0 to 64 [ 35.487255] ata3: SATA max UDMA/133 cmd 0x9E0 ctl 0xBE2 bmdma 0xC400 irq 217 [ 35.487273] ata4: SATA max UDMA/133 cmd 0x960 ctl 0xB62 bmdma 0xC408 irq 217 [ 35.490045] SCSI device sda: 490232639 512-byte hdwr sectors (250999 MB) [ 35.490056] sda: Write Protect is off [ 35.490058] sda: Mode Sense: 00 3a 00 00 [ 35.490069] SCSI device sda: drive cache: write back [ 35.490118] SCSI device sda: 490232639 512-byte hdwr sectors (250999 MB) [ 35.490125] sda: Write Protect is off [ 35.490127] sda: Mode Sense: 00 3a 00 00 [ 35.490138] SCSI device sda: drive cache: write back [ 35.490142] sda: sda1 sda2 < sda5 > [ 35.531089] sd 0:0:0:0: Attached scsi disk sda [ 35.531731] SCSI device sdb: 490234752 512-byte hdwr sectors (251000 MB) [ 35.532405] sdb: Write Protect is off [ 35.532408] sdb: Mode Sense: 00 3a 00 00 [ 35.532435] SCSI device sdb: drive cache: write back [ 35.532482] SCSI device sdb: 490234752 512-byte hdwr sectors (251000 MB) [ 35.532497] sdb: Write Protect is off [ 35.532499] sdb: Mode Sense: 00 3a 00 00 [ 35.532510] SCSI device sdb: drive cache: write back [ 35.532513] sdb: sdb1 [ 35.542503] sd 1:0:0:0: Attached scsi disk sdb [ 35.692383] ata3: SATA link down (SStatus 0) [ 35.692389] scsi2 : sata_nv [ 35.896235] ata4: SATA link up 3.0 Gbps (SStatus 123) [ 36.060272] ata4: dev 0 cfg 49:2f00 82:746b 83:7f61 84:4063 85:7469 86:3c41 87:4063 88:407f [ 36.060276] ata4: dev 0 ATA-7, max UDMA/133, 490234752 sectors: LBA48 [ 36.072262] ata4: dev 0 configured for UDMA/133 [ 36.072265] scsi3 : sata_nv [ 36.072870] Vendor: ATA Model: WDC WD2500YS-01S Rev: 20.0 [ 36.072879] Type: Direct-Access ANSI SCSI revision: 05 [ 36.073337] SCSI device sdc: 490234752 512-byte hdwr sectors (251000 MB) [ 36.073347] sdc: Write Protect is off [ 36.073349] sdc: Mode Sense: 00 3a 00 00 [ 36.073361] SCSI device sdc: drive cache: write back [ 36.073404] SCSI device sdc: 490234752 512-byte hdwr sectors (251000 MB) [ 36.073411] sdc: Write Protect is off [ 36.073413] sdc: Mode Sense: 00 3a 00 00 [ 36.073424] SCSI device sdc: drive cache: write back [ 36.073427] sdc: sdc1 [ 36.077108] sd 3:0:0:0: Attached scsi disk sdc [ 36.077907] NFORCE-MCP51: IDE controller at PCI slot 0000:00:0d.0 [ 36.077926] NFORCE-MCP51: chipset revision 161 [ 36.077928] NFORCE-MCP51: not 100% native mode: will probe irqs later [ 36.077931] NFORCE-MCP51: BIOS didn't set cable bits correctly. Enabling workaround. [ 36.077935] NFORCE-MCP51: 0000:00:0d.0 (rev a1) UDMA133 controller [ 36.077943] ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:DMA [ 36.077952] ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DMA [ 36.077959] Probing IDE interface ide0... [ 36.647699] Probing IDE interface ide1... [ 37.387269] hdc: SONY DVD-ROM DDU1615, ATAPI CD/DVD-ROM drive [ 38.058850] ide1 at 0x170-0x177,0x376 on irq 15 [ 38.067976] hdc: ATAPI 40X DVD-ROM drive, 1725kB Cache, UDMA(66) [ 38.067984] Uniform CD-ROM driver Revision: 3.20 [ 38.238666] Probing IDE interface ide0... [ 38.285495] forcedeth.c: Reverse Engineered nForce ethernet driver. Version 0.54. [ 38.285938] ACPI: PCI Interrupt Link [APCH] enabled at IRQ 21 [ 38.285943] GSI 18 sharing vector 0xE1 and IRQ 18 [ 38.285946] ACPI: PCI Interrupt 0000:00:14.0[A] -> Link [APCH] -> GSI 21 (level, low) -> IRQ 225 [ 38.285952] PCI: Setting latency timer of device 0000:00:14.0 to 64 [ 38.285961] forcedeth: using HIGHDMA [ 38.315630] ieee1394: Initialized config rom entry `ip1394' [ 38.326609] usbcore: registered new driver usbfs [ 38.327088] usbcore: registered new driver hub [ 38.328801] ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) [ 38.806466] eth0: forcedeth.c: subsystem: 01458:e000 bound to 0000:00:14.0 [ 38.807598] ACPI: PCI Interrupt Link [APC3] enabled at IRQ 18 [ 38.807605] GSI 19 sharing vector 0xE9 and IRQ 19 [ 38.807608] ACPI: PCI Interrupt 0000:01:0e.0[A] -> Link [APC3] -> GSI 18 (level, low) -> IRQ 233 [ 38.859395] ACPI: PCI Interrupt Link [APCF] enabled at IRQ 20 [ 38.859402] GSI 20 sharing vector 0x32 and IRQ 20 [ 38.859405] ACPI: PCI Interrupt 0000:00:0b.0[A] -> Link [APCF] -> GSI 20 (level, low) -> IRQ 50 [ 38.859486] PCI: Setting latency timer of device 0000:00:0b.0 to 64 [ 38.859491] ohci_hcd 0000:00:0b.0: OHCI Host Controller [ 38.859777] ohci_hcd 0000:00:0b.0: new USB bus registered, assigned bus number 1 [ 38.872611] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[233] MMIO=[f5004000-f50047ff] Max Packet=[2048] IR/IT contexts=[4/8] [ 38.878135] ohci_hcd 0000:00:0b.0: irq 50, io mem 0xf5108000 [ 38.936133] usb usb1: configuration #1 chosen from 1 choice [ 38.936153] hub 1-0:1.0: USB hub found [ 38.936162] hub 1-0:1.0: 8 ports detected [ 39.043096] ACPI: PCI Interrupt Link [APCL] enabled at IRQ 23 [ 39.043101] ACPI: PCI Interrupt 0000:00:0b.1[B] -> Link [APCL] -> GSI 23 (level, low) -> IRQ 209 [ 39.043212] PCI: Setting latency timer of device 0000:00:0b.1 to 64 [ 39.043218] ehci_hcd 0000:00:0b.1: EHCI Host Controller [ 39.043268] ehci_hcd 0000:00:0b.1: new USB bus registered, assigned bus number 2 [ 39.043299] ehci_hcd 0000:00:0b.1: debug port 1 [ 39.043302] PCI: cache line size of 64 is not supported by device 0000:00:0b.1 [ 39.043310] ehci_hcd 0000:00:0b.1: irq 209, io mem 0xf5104000 [ 39.043317] ehci_hcd 0000:00:0b.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 [ 39.043370] usb usb2: configuration #1 chosen from 1 choice [ 39.043388] hub 2-0:1.0: USB hub found [ 39.043394] hub 2-0:1.0: 8 ports detected [ 39.201731] Attempting manual resume [ 39.214265] EXT3-fs: INFO: recovery required on readonly filesystem. [ 39.214269] EXT3-fs: write access will be enabled during recovery. [ 40.145868] ieee1394: Host added: ID:BUS[0-00:1023] GUID[0016e60000c4946a] [ 41.526826] kjournald starting. Commit interval 5 seconds [ 41.526843] EXT3-fs: sda1: orphan cleanup on readonly fs [ 41.526850] ext3_orphan_cleanup: deleting unreferenced inode 6733864 [ 41.543718] ext3_orphan_cleanup: deleting unreferenced inode 6733844 [ 41.545229] EXT3-fs: sda1: 2 orphan inodes deleted [ 41.545231] EXT3-fs: recovery complete. [ 41.595936] EXT3-fs: mounted filesystem with ordered data mode. [ 48.043276] pci_hotplug: PCI Hot Plug PCI Core version: 0.5 [ 48.046129] shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 [ 48.738455] 8139too Fast Ethernet driver 0.9.27 [ 48.740097] ACPI: PCI Interrupt Link [APC1] enabled at IRQ 16 [ 48.740103] GSI 21 sharing vector 0x3A and IRQ 21 [ 48.740107] ACPI: PCI Interrupt 0000:01:06.0[A] -> Link [APC1] -> GSI 16 (level, low) -> IRQ 58 [ 48.740751] eth1: RealTek RTL8139 at 0xffffc200100a0000, 00:08:a1:57:6b:94, IRQ 58 [ 48.740754] eth1: Identified 8139 chip type 'RTL-8100B/8139D' [ 48.757936] input: PC Speaker as /class/input/input1 [ 48.882038] parport: PnPBIOS parport detected. [ 48.882091] parport0: PC-style at 0x378, irq 7 [PCSPP,TRISTATE] [ 48.991870] sd 0:0:0:0: Attached scsi generic sg0 type 0 [ 48.993303] sd 1:0:0:0: Attached scsi generic sg1 type 0 [ 48.994835] sd 3:0:0:0: Attached scsi generic sg2 type 0 [ 49.005289] 8139cp: 10/100 PCI Ethernet driver v1.2 (Mar 22, 2004) [ 49.075184] logips2pp: Detected unknown logitech mouse model 1 [ 49.141054] Floppy drive(s): fd0 is 1.44M [ 49.146273] eth1: link down [ 49.162474] FDC 0 is a post-1991 82077 [ 49.249735] input: PS/2 Logitech Mouse as /class/input/input2 [ 49.280645] ts: Compaq touchscreen protocol output [ 49.401221] ACPI: PCI Interrupt Link [AAZA] enabled at IRQ 22 [ 49.401226] ACPI: PCI Interrupt 0000:00:10.1[B] -> Link [AAZA] -> GSI 22 (level, low) -> IRQ 217 [ 49.401306] PCI: Setting latency timer of device 0000:00:10.1 to 64 [ 49.786372] hda_codec: Unknown model for ALC883, trying auto-probe from BIOS... [ 50.125046] NET: Registered protocol family 17 [ 50.159471] lp0: using parport0 (interrupt-driven). [ 50.189138] ieee1394: sbp2: Driver forced to serialize I/O (serialize_io=1) [ 50.189142] ieee1394: sbp2: Try serialize_io=0 for better performance [ 50.224998] Adding 5839588k swap on /dev/disk/by-uuid/1e988424-bef9-4a9b-9d24-51e00ac983b5. Priority:-1 extents:1 across:5839588k [ 50.267573] EXT3 FS on sda1, internal journal [ 52.172004] NET: Registered protocol family 10 [ 52.172101] lo: Disabled Privacy Extensions [ 52.172429] ADDRCONF(NETDEV_UP): eth1: link is not ready [ 52.172454] IPv6 over IPv4 tunneling driver [ 55.335702] ACPI: Power Button (FF) [PWRF] [ 55.335711] ACPI: Power Button (CM) [PWRB] [ 55.429620] ibm_acpi: ec object not found [ 55.455323] pcc_acpi: loading... [ 55.727774] powernow-k8: Found 1 AMD Athlon 64 / Opteron processors (version 1.60.2) [ 55.727816] powernow-k8: 0 : fid 0xe (2200 MHz), vid 0x8 (1350 mV) [ 55.727818] powernow-k8: 1 : fid 0xc (2000 MHz), vid 0xa (1300 mV) [ 55.727821] powernow-k8: 2 : fid 0xa (1800 MHz), vid 0xc (1250 mV) [ 55.727823] powernow-k8: 3 : fid 0x2 (1000 MHz), vid 0x12 (1100 mV) [ 55.727827] cpu_init done, current fid 0xe, vid 0x8 [ 60.487093] Bluetooth: Core ver 2.8 [ 60.487099] NET: Registered protocol family 31 [ 60.487101] Bluetooth: HCI device and connection manager initialized [ 60.487122] Bluetooth: HCI socket layer initialized [ 60.497734] Bluetooth: L2CAP ver 2.8 [ 60.497738] Bluetooth: L2CAP socket layer initialized [ 60.515848] Bluetooth: RFCOMM socket layer initialized [ 60.515864] Bluetooth: RFCOMM TTY layer initialized [ 60.515866] Bluetooth: RFCOMM ver 1.7 [ 61.990726] eth0: no IPv6 routers present [ 2359.626088] kjournald starting. Commit interval 5 seconds [ 2359.632237] EXT3 FS on sdb1, internal journal [ 2359.632361] EXT3-fs: mounted filesystem with ordered data mode. [ 2865.865755] eth0: Promiscuous mode enabled. [ 2865.865811] device eth0 entered promiscuous mode [ 2865.865817] audit(1170015114.575:2): dev=eth0 prom=256 old_prom=0 auid=4294967295 [ 2869.058057] device eth0 left promiscuous mode [ 2869.058065] audit(1170015121.603:3): dev=eth0 prom=0 old_prom=256 auid=4294967295 [ 5057.960058] EXT3-fs error (device sdb1): ext3_free_blocks_sb: bit already cleared for block 52174318 [ 5057.960065] Aborting journal on device sdb1. [ 5057.964432] EXT3-fs error (device sdb1) in ext3_free_blocks_sb: Journal has aborted [ 5057.964686] EXT3-fs error (device sdb1) in ext3_free_blocks_sb: Journal has aborted [ 5057.964930] EXT3-fs error (device sdb1) in ext3_reserve_inode_write: Journal has aborted [ 5057.965181] EXT3-fs error (device sdb1) in ext3_truncate: Journal has aborted [ 5057.965433] EXT3-fs error (device sdb1) in ext3_reserve_inode_write: Journal has aborted [ 5057.965682] EXT3-fs error (device sdb1) in ext3_orphan_del: Journal has aborted [ 5057.965916] EXT3-fs error (device sdb1) in ext3_reserve_inode_write: Journal has aborted [ 5057.966167] EXT3-fs error (device sdb1) in ext3_delete_inode: Journal has aborted [ 5057.966385] __journal_remove_journal_head: freeing b_committed_data [ 5057.966392] __journal_remove_journal_head: freeing b_committed_data [ 5057.966397] __journal_remove_journal_head: freeing b_committed_data [ 5057.966853] ext3_abort called. [ 5057.966856] EXT3-fs error (device sdb1): ext3_journal_start_sb: Detected aborted journal [ 5057.966859] Remounting filesystem read-only
00:00.0 RAM memory: nVidia Corporation C51 Host Bridge (rev a2) 00:00.1 RAM memory: nVidia Corporation C51 Memory Controller 0 (rev a2) 00:00.2 RAM memory: nVidia Corporation C51 Memory Controller 1 (rev a2) 00:00.3 RAM memory: nVidia Corporation C51 Memory Controller 5 (rev a2) 00:00.4 RAM memory: nVidia Corporation C51 Memory Controller 4 (rev a2) 00:00.5 RAM memory: nVidia Corporation C51 Host Bridge (rev a2) 00:00.6 RAM memory: nVidia Corporation C51 Memory Controller 3 (rev a2) 00:00.7 RAM memory: nVidia Corporation C51 Memory Controller 2 (rev a2) 00:02.0 PCI bridge: nVidia Corporation C51 PCI Express Bridge (rev a1) 00:03.0 PCI bridge: nVidia Corporation C51 PCI Express Bridge (rev a1) 00:04.0 PCI bridge: nVidia Corporation C51 PCI Express Bridge (rev a1) 00:05.0 VGA compatible controller: nVidia Corporation C51G [GeForce 6100] (rev a2) 00:09.0 RAM memory: nVidia Corporation MCP51 Host Bridge (rev a2) 00:0a.0 ISA bridge: nVidia Corporation MCP51 LPC Bridge (rev a3) 00:0a.1 SMBus: nVidia Corporation MCP51 SMBus (rev a3) 00:0a.2 RAM memory: nVidia Corporation MCP51 Memory Controller 0 (rev a3) 00:0b.0 USB Controller: nVidia Corporation MCP51 USB Controller (rev a3) 00:0b.1 USB Controller: nVidia Corporation MCP51 USB Controller (rev a3) 00:0d.0 IDE interface: nVidia Corporation MCP51 IDE (rev a1) 00:0e.0 IDE interface: nVidia Corporation MCP51 Serial ATA Controller (rev a1) 00:0f.0 IDE interface: nVidia Corporation MCP51 Serial ATA Controller (rev a1) 00:10.0 PCI bridge: nVidia Corporation MCP51 PCI Bridge (rev a2) 00:10.1 Audio device: nVidia Corporation MCP51 High Definition Audio (rev a2) 00:14.0 Bridge: nVidia Corporation MCP51 Ethernet Controller (rev a3) 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control 01:06.0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8139/8139C/8139C+ (rev 10) 01:0e.0 FireWire (IEEE 1394): Texas Instruments TSB43AB23 IEEE-1394a-2000 Controller (PHY/Link)
_______________________________________________ Ext3-users mailing list Ext3-users@xxxxxxxxxx https://www.redhat.com/mailman/listinfo/ext3-users
