Add the device tree binding documentation for Mediatek HDMI,
HDMI PHY and HDMI DDC devices.
Signed-off-by: Philipp Zabel <p.zabel@xxxxxxxxxxxxxx>
Acked-by: Rob Herring <robh@xxxxxxxxxx>
---
.../bindings/display/mediatek/mediatek,hdmi.txt | 148 +++++++++++++++++++++
1 file changed, 148 insertions(+)
create mode 100644 Documentation/devicetree/bindings/display/mediatek/mediatek,hdmi.txt
diff --git a/Documentation/devicetree/bindings/display/mediatek/mediatek,hdmi.txt b/Documentation/devicetree/bindings/display/mediatek/mediatek,hdmi.txt
new file mode 100644
index 0000000..7b12424
--- /dev/null
+++ b/Documentation/devicetree/bindings/display/mediatek/mediatek,hdmi.txt
@@ -0,0 +1,148 @@
+Mediatek HDMI Encoder
+=====================
+
+The Mediatek HDMI encoder can generate HDMI 1.4a or MHL 2.0 signals from
+its parallel input.
+
+Required properties:
+- compatible: Should be "mediatek,<chip>-hdmi".
+- reg: Physical base address and length of the controller's registers
+- interrupts: The interrupt signal from the function block.
+- clocks: device clocks
+ See Documentation/devicetree/bindings/clock/clock-bindings.txt for details.
+- clock-names: must contain "pixel", "pll", "bclk", and "spdif".
+- phys: phandle link to the HDMI PHY node.
+ See Documentation/devicetree/bindings/phy/phy-bindings.txt for details.
+- phy-names: must contain "hdmi"
+- mediatek,syscon-hdmi: phandle link and register offset to the system
+ configuration registers. For mt8173 this must be offset 0x900 into the
+ MMSYS_CONFIG region: <&mmsys 0x900>.
+- ports: A node containing input and output port nodes with endpoint
+ definitions as documented in Documentation/devicetree/bindings/graph.txt.
+- port@0: The input port in the ports node should be connected to a DPI output
+ port.
+- port@1: The output port in the ports node should be connected to the input
+ port of a connector node that contains a ddc-i2c-bus property, or to the
+ input port of an attached bridge chip, such as a SlimPort transmitter.
+
+HDMI CEC
+========
+
+The HDMI CEC controller handles hotplug detection and CEC communication.
+
+Required properties:
+- compatible: Should be "mediatek,<chip>-cec"
+- reg: Physical base address and length of the controller's registers
+- interrupts: The interrupt signal from the function block.
+- clocks: device clock
+
+HDMI DDC
+========
+
+The HDMI DDC i2c controller is used to interface with the HDMI DDC pins.
+The Mediatek's I2C controller is used to interface with I2C devices.
+
+Required properties:
+- compatible: Should be "mediatek,<chip>-hdmi-ddc"
+- reg: Physical base address and length of the controller's registers
+- clocks: device clock
+- clock-names: Should be "ddc-i2c".
+
+HDMI PHY
+========
+
+The HDMI PHY serializes the HDMI encoder's three channel 10-bit parallel
+output and drives the HDMI pads.
+
+Required properties:
+- compatible: "mediatek,<chip>-hdmi-phy"
+- reg: Physical base address and length of the module's registers
+- clocks: PLL reference clock
+- clock-names: must contain "pll_ref"
+- clock-output-names: must be "hdmitx_dig_cts" on mt8173
+- #phy-cells: must be <0>
+- #clock-cells: must be <0>
+
+Optional properties:
+- mediatek,ibias: TX DRV bias current for <1.65Gbps, defaults to 0xa
+- mediatek,ibias_up: TX DRV bias current for >1.65Gbps, defaults to 0x1c
+
+Example:
+
+cec: cec@10013000 {
+ compatible = "mediatek,mt8173-cec";
+ reg = <0 0x10013000 0 0xbc>;
+ interrupts = <GIC_SPI 167 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&infracfg CLK_INFRA_CEC>;
+};
+
+hdmi_phy: hdmi-phy@10209100 {
+ compatible = "mediatek,mt8173-hdmi-phy";
+ reg = <0 0x10209100 0 0x24>;
+ clocks = <&apmixedsys CLK_APMIXED_HDMI_REF>;
+ clock-names = "pll_ref";
+ clock-output-names = "hdmitx_dig_cts";
+ mediatek,ibias = <0xa>;
+ mediatek,ibias_up = <0x1c>;
+ #clock-cells = <0>;
+ #phy-cells = <0>;
+};
+
+hdmi_ddc0: i2c@11012000 {
+ compatible = "mediatek,mt8173-hdmi-ddc";
+ reg = <0 0x11012000 0 0x1c>;
+ interrupts = <GIC_SPI 81 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&pericfg CLK_PERI_I2C5>;
+ clock-names = "ddc-i2c";
+};
+
+hdmi0: hdmi@14025000 {
+ compatible = "mediatek,mt8173-hdmi";
+ reg = <0 0x14025000 0 0x400>;
+ interrupts = <GIC_SPI 206 IRQ_TYPE_LEVEL_LOW>;
+ clocks = <&mmsys CLK_MM_HDMI_PIXEL>,
+ <&mmsys CLK_MM_HDMI_PLLCK>,
+ <&mmsys CLK_MM_HDMI_AUDIO>,
+ <&mmsys CLK_MM_HDMI_SPDIF>;
+ clock-names = "pixel", "pll", "bclk", "spdif";
+ pinctrl-names = "default";
+ pinctrl-0 = <&hdmi_pin>;
+ phys = <&hdmi_phy>;
+ phy-names = "hdmi";
+ mediatek,syscon-hdmi = <&mmsys 0x900>;
+ assigned-clocks = <&topckgen CLK_TOP_HDMI_SEL>;
+ assigned-clock-parents = <&hdmi_phy>;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ hdmi0_in: endpoint {
+ remote-endpoint = <&dpi0_out>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ hdmi0_out: endpoint {
+ remote-endpoint = <&hdmi_con_in>;
+ };
+ };
+ };
+};
+
+connector {
+ compatible = "hdmi-connector";
+ type = "a";
+ ddc-i2c-bus = <&hdmiddc0>;
+
+ port {
+ hdmi_con_in: endpoint {
+ remote-endpoint = <&hdmi0_out>;
+ };
+ };
+};
--
2.7.0.rc3
_______________________________________________
dri-devel mailing list
dri-devel@xxxxxxxxxxxxxxxxxxxxx
http://lists.freedesktop.org/mailman/listinfo/dri-devel
