Re: [PATCH v11 0/19] Add Analogix Core Display Port Driver

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Yakir,

Am Mittwoch, 16. Dezember 2015, 11:20:18 schrieb Yakir Yang:
>    The Samsung Exynos eDP controller and Rockchip RK3288 eDP controller
> share the same IP, so a lot of parts can be re-used. I split the common
> code into bridge directory, then rk3288 and exynos only need to keep
> some platform code. Cause I can't find the exact IP name of exynos dp
> controller, so I decide to name dp core driver with "analogix" which I
> find in rk3288 eDP TRM

I'm really sorry for not thinking of this earlier, but I think we'll be doing 
the atomic modesetting conversion of the drm/kms driver first - see v3 series 
from Mark Yao.

Could you handle necessary changes to make it apply and work _after_ the 
atomic modesetting conversion please?


Thanks
Heiko


> But  there are still three light registers setting differents bewteen
> exynos and rk3288.
> 1. RK3288 have five special pll resigters which not indicata in exynos
>    dp controller.
> 2. The address of DP_PHY_PD(dp phy power manager register) are different
>    between rk3288 and exynos.
> 3. Rk3288 and exynos have different setting with AUX_HW_RETRY_CTL(dp debug
>    register).
> 
> This series have been well tested on Rockchip platform with eDP panel on
> Jerry Chromebook and Display Port Monitor on RK3288 board. Also I have
> tested on Samsung Snow and Peach Pit Chromebooks, and thanks to
> Javier@Samsung help to retest the whole series on Samsung Exynos5800 Peach
> Pi Chromebook, glad to say that things works rightlly.
> 
> Thanks,
> - Yakir
> 
> 
> Changes in v11:
> - Uses tabs to fix the indentation issues in analogix_dp_core.h (Heiko)
> - Correct the title of this rockchip dp phy document(Rob)
> - Add the ack from Rob Herring
> - Rename the "analogix,need-force-hpd" to common 'force-hpd' (Rob)
> - Add the ack from Rob Herring
> - Revert parts of Gustavo Padovan's changes in commit:
> 	drm/exynos: do not start enabling DP at bind() phase
>   Add dp phy poweron function in bind time.
> - Move the panel prepare from get_modes time to bind time, and move
>   the panel unprepare from bridge->disable to unbind time. (Heiko)
> 
> Changes in v10:
> - Add the ack from Rob Herring
> - Correct the ROCKCHIP_ANALOGIX_DP indentation in Kconfig to tabs here
> (Heiko) - Add the ack from Rob Herring
> - Fix the wrong macro value of GRF_EDP_REF_CLK_SEL_INTER_HIWORD_MASK
>     BIT(4) -> BIT(20)
> - Remove the surplus "plat_data" check. (Heiko)
> -       switch (dp->plat_data && dp->plat_data->dev_type) {
> +       switch (dp->plat_data->dev_type) {
> 
> Changes in v9:
> - Document more details for 'ports' property.
> - Removed the unused the variable "res" in probe function. (Heiko)
> - Removed the unused head file.
> 
> Changes in v8:
> - Correct the right document path of display-timing.txt (Heiko)
> - Correct the misspell of 'from' to 'frm'. (Heiko)
> - Modify the commit subject name. (Heiko)
> - Fix the mixed spacers on macro definitions. (Heiko)
> - Remove the unnecessary empty line after clk_prepare_enable. (Heiko)
> - Remove the specific address in the example node name. (Heiko)
> 
> Changes in v7:
> - Back to use the of_property_read_bool() interfacs to provoid backward
>   compatibility of "hsync-active-high" "vsync-active-high" "interlaced"
>   to avoid -EOVERFLOW error (Krzysztof)
> - Simply the commit message. (Kishon)
> - Symmetrical enable/disbale the phy clock and power. (Kishon)
> - Simplify the commit message. (Kishon)
> 
> Changes in v6:
> - Fix the Kconfig recursive dependency (Javier)
> - Fix Peach Pit hpd property name error:
> -       hpd-gpio = <&gpx2 6 0>;
> +       hpd-gpios = <&gpx2 6 0>;
> 
> Changes in v5:
> - Correct the check condition of gpio_is_valid when driver try to get
>   the "hpd-gpios" DT propery. (Heiko)
> - Move the platform attach callback in the front of core driver bridge
>   attch function. Cause once platform failed at attach, core driver should
>   still failed, so no need to init connector before platform attached
> (Krzysztof) - Keep code style no changes with the previous exynos_dp_code.c
> in this patch, and update commit message about the new export symbol
> (Krzysztof) - Gather the device type patch (v4 11/16) into this one.
> (Krzysztof) - leave out the connector registration to analogix platform
> driver. (Thierry) - Resequence this patch after analogix_dp driver have
> been split
>   from exynos_dp code, and rephrase reasonable commit message, and
>   remove some controversial style (Krzysztof)
>     -		analogix_dp_write_byte_to_dpcd(
>     - 				dp, DP_TEST_RESPONSE,
>     +		analogix_dp_write_byte_to_dpcd(dp,
>     +				DP_TEST_RESPONSE,
> 				DP_TEST_EDID_CHECKSUM_WRITE);
> - Switch video timing type to "u32", so driver could use
> "of_property_read_u32" to get the backword timing values. Krzysztof suggest
> me that driver could use the "of_property_read_bool" to get backword timing
> values, but that interfacs would modify the original drm_display_mode
> timing directly (whether those properties exists or not).
> - Correct the misspell in commit message. (Krzysztof)
> - Remove the empty line at the end of document, and correct the endpoint
>   numbers in the example DT node, and remove the regulator iomux setting
>   in driver code while using the pinctl in devicetree instead. (Heiko)
> - Add device type declared, cause the previous "platform device type
>   support (v4 11/16)" already merge into (v5 02/14).
> - Implement connector registration code. (Thierry)
> - Split binding doc's from driver changes. (Rob)
> - Add eDP hotplug pinctrl property. (Heiko)
> - Remove "reg" DT property, cause driver could poweron/poweroff phy via
>   the exist "grf" syscon already. And rename the example DT node from
>   "edp_phy: phy@ff770274" to "edp_phy: edp-phy" directly. (Heiko)
> - Add deivce_node at the front of driver, update phy_ops type from "static
>   struct" to "static const struct". And correct the input paramters of
>   devm_phy_create() interfaces. (Heiko)
> - Split binding doc's from driver changes. (Rob)
> - Update the rockchip,grf explain in document, and correct the clock
> required elemets in document. (Rob & Heiko)
> - Fix compiled error (Heiko)
> - Using the connector display info message to configure eDP driver input
>   video mode, but hard code CRTC video output mode to RGBaaa.
> 
> Changes in v4:
> - Update "analogix,hpd-gpios" to "hpd-gpios" DT propery. (Rob)
> - Rename "analogix_dp-exynos.c" file name to "exynos_dp.c" (Jingoo)
> - Create a separate folder for analogix code in bridge/ (Archit)
> - Update commit message more readable. (Jingoo)
> - Adjust the order from 05 to 04
> - Provide backword compatibility with samsung. (Krzysztof)
> - Split all DTS changes, and provide backward compatibility. Mark old
>   properties as deprecated but still support them. (Krzysztof)
> - Update "analogix,hpd-gpio" to "hpd-gpios" prop name. (Rob)
> - Deprecated some properties which could parsed from Edid/Mode/DPCD.
> (Thierry) "analogix,color-space" & "analogix,color-depth"   &
>     "analogix,link-rate"   & "analogix,lane-count"    &
>     "analogix,ycbcr-coeff" & "analogix,dynamic-range" &
>     "vsync-active-high"    & "hsync-active-high"      & "interlaces"
> - Separate all DTS changes to a separate patch. (Krzysztof)
> - Remove some deprecated DT properties in rockchip dp document.
> - Add commit message, and remove the redundant rockchip_dp_phy_init()
>   function, move those code to probe() method. And remove driver .owner
>   number. (Kishon)
> - Seprate the link-rate and lane-count limit out with the device_type
>   flag. (Thierry)
> - Take Jingoo suggest, add commit messages.
> - Call drm_panel_prepare() in .get_modes function, ensure panel should
>   power on before driver try to read edid message.
> 
> Changes in v3:
> - Move exynos's video_timing code to analogix_dp-exynos platform driver,
>   add get_modes method to struct analogix_dp_plat_data. (Thierry)
> - Rename some "samsung*" dts propery to "analogix*". (Heiko)
> - The link_rate and lane_count shouldn't config to the DT property value
>   directly, but we can take those as hardware limite. For example, RK3288
>   only support 4 physical lanes of 2.7/1.62 Gbps/lane, so DT property would
>   like "link-rate = 0x0a" "lane-count = 4". (Thierry)
> - Dynamic parse video timing info from struct drm_display_mode and
>   struct drm_display_info. (Thierry)
> - Add devicetree binding documents. (Heiko)
> - Remove sync pol & colorimetry properies from the new analogix dp driver
>   devicetree binding. (Thierry)
> - Update the exist exynos dtsi file with the latest DP DT properies.
> - Leave "sclk_edp_24m" to rockchip dp phy driver which name to "24m",
>   and leave "sclk_edp" to analogix dp core driver which name to "dp",
>   and leave "pclk_edp" to rockchip dp platform driver which name to
>   "pclk". (Thierry & Heiko)
> - Add devicetree binding document. (Heiko)
> - Remove "rockchip,panel" DT property, take use of remote point to get panel
> node. (Heiko)
> - Add the new function point dp_platdata->get_modes() init.
> - Suggest, add rockchip dp phy driver, collect the phy clocks and
>   power control. (Heiko)
> - Add "analogix,need-force-hpd" to indicate whether driver need foce
>   hpd when hpd detect failed.
> - move dp hpd detect to connector detect function.
> - Add edid modes parse support
> 
> Changes in v2:
> - Remove new copyright (Jingoo)
> - Fix compiled failed due to analogix_dp_device misspell
> - Improved commit message more readable, and avoid using some
>   uncommon style like bellow: (Joe Preches)
>     -  retval = exynos_dp_read_bytes_from_i2c(...
>   				  ...);
>     +  retval =
>     +  exynos_dp_read_bytes_from_i2c(......);
> - Get panel node with remote-endpoint method, and create devicetree binding
>   for driver. (Heiko)
> - Remove the clock enable/disbale with "sclk_edp" & "sclk_edp_24m",
>   leave those clock to rockchip dp phy driver.
> - Fix compile failed dut to phy_pd_addr variable misspell error
> 
> Mark Yao (1):
>   drm: rockchip: vop: add bpc and color mode setting
> 
> Yakir Yang (18):
>   drm: bridge: analogix/dp: split exynos dp driver to bridge directory
>   drm: bridge: analogix/dp: fix some obvious code style
>   drm: bridge: analogix/dp: remove duplicate configuration of link rate
>     and link count
>   drm: bridge: analogix/dp: dynamic parse sync_pol & interlace &
>     dynamic_range
>   dt-bindings: add document for analogix display port driver
>   ARM: dts: exynos/dp: remove some properties that deprecated by
>     analogix_dp driver
>   drm: rockchip: dp: add rockchip platform dp driver
>   dt-bindings: add document for rockchip variant of analogix_dp
>   phy: Add driver for rockchip Display Port PHY
>   dt-bindings: add document for rockchip dp phy
>   drm: bridge: analogix/dp: add some rk3288 special registers setting
>   drm: bridge: analogix/dp: add max link rate and lane count limit for
>     RK3288
>   drm: bridge: analogix/dp: try force hpd after plug in lookup failed
>   drm: bridge: analogix/dp: move hpd detect to connector detect function
>   drm: bridge: analogix/dp: add edid modes parse in get_modes method
>   drm: bridge: analogix/dp: expand the look time for waiting AUX CH
>     reply
>   drm: bridge: analogix/dp: add panel prepare/unprepare in
>     suspend/resume time
>   drm: bridge: analogix/dp: Fix the possible dead lock in bridge disable
>     time
> 
>  .../bindings/display/bridge/analogix_dp.txt        |   52 +
>  .../bindings/display/exynos/exynos_dp.txt          |   66 +-
>  .../display/rockchip/analogix_dp-rockchip.txt      |   92 ++
>  .../devicetree/bindings/phy/rockchip-dp-phy.txt    |   22 +
>  arch/arm/boot/dts/exynos5250-arndale.dts           |    2 -
>  arch/arm/boot/dts/exynos5250-smdk5250.dts          |    2 -
>  arch/arm/boot/dts/exynos5250-snow-common.dtsi      |    4 +-
>  arch/arm/boot/dts/exynos5250-spring.dts            |    4 +-
>  arch/arm/boot/dts/exynos5420-peach-pit.dts         |    4 +-
>  arch/arm/boot/dts/exynos5420-smdk5420.dts          |    2 -
>  arch/arm/boot/dts/exynos5800-peach-pi.dts          |    4 +-
>  drivers/gpu/drm/bridge/Kconfig                     |    2 +
>  drivers/gpu/drm/bridge/Makefile                    |    1 +
>  drivers/gpu/drm/bridge/analogix/Kconfig            |    3 +
>  drivers/gpu/drm/bridge/analogix/Makefile           |    1 +
>  drivers/gpu/drm/bridge/analogix/analogix_dp_core.c | 1387
> ++++++++++++++++++ drivers/gpu/drm/bridge/analogix/analogix_dp_core.h | 
> 287 ++++
>  drivers/gpu/drm/bridge/analogix/analogix_dp_reg.c  | 1320 +++++++++++++++++
> .../analogix/analogix_dp_reg.h}                    |  270 ++--
>  drivers/gpu/drm/exynos/Kconfig                     |    3 +-
>  drivers/gpu/drm/exynos/Makefile                    |    2 +-
>  drivers/gpu/drm/exynos/exynos_dp.c                 |  384 +++++
>  drivers/gpu/drm/exynos/exynos_dp_core.c            | 1515
> -------------------- drivers/gpu/drm/exynos/exynos_dp_core.h            | 
> 282 ----
>  drivers/gpu/drm/exynos/exynos_dp_reg.c             | 1263 ----------------
>  drivers/gpu/drm/rockchip/Kconfig                   |    9 +
>  drivers/gpu/drm/rockchip/Makefile                  |    1 +
>  drivers/gpu/drm/rockchip/analogix_dp-rockchip.c    |  457 ++++++
>  drivers/gpu/drm/rockchip/dw_hdmi-rockchip.c        |    2 +-
>  drivers/gpu/drm/rockchip/rockchip_drm_drv.h        |    2 +-
>  drivers/gpu/drm/rockchip/rockchip_drm_vop.c        |   32 +-
>  drivers/phy/Kconfig                                |    7 +
>  drivers/phy/Makefile                               |    1 +
>  drivers/phy/phy-rockchip-dp.c                      |  151 ++
>  include/drm/bridge/analogix_dp.h                   |   42 +
>  35 files changed, 4421 insertions(+), 3257 deletions(-)
>  create mode 100644
> Documentation/devicetree/bindings/display/bridge/analogix_dp.txt create
> mode 100644
> Documentation/devicetree/bindings/display/rockchip/analogix_dp-rockchip.txt
> create mode 100644
> Documentation/devicetree/bindings/phy/rockchip-dp-phy.txt create mode
> 100644 drivers/gpu/drm/bridge/analogix/Kconfig
>  create mode 100644 drivers/gpu/drm/bridge/analogix/Makefile
>  create mode 100644 drivers/gpu/drm/bridge/analogix/analogix_dp_core.c
>  create mode 100644 drivers/gpu/drm/bridge/analogix/analogix_dp_core.h
>  create mode 100644 drivers/gpu/drm/bridge/analogix/analogix_dp_reg.c
>  rename drivers/gpu/drm/{exynos/exynos_dp_reg.h =>
> bridge/analogix/analogix_dp_reg.h} (62%) create mode 100644
> drivers/gpu/drm/exynos/exynos_dp.c
>  delete mode 100644 drivers/gpu/drm/exynos/exynos_dp_core.c
>  delete mode 100644 drivers/gpu/drm/exynos/exynos_dp_core.h
>  delete mode 100644 drivers/gpu/drm/exynos/exynos_dp_reg.c
>  create mode 100644 drivers/gpu/drm/rockchip/analogix_dp-rockchip.c
>  create mode 100644 drivers/phy/phy-rockchip-dp.c
>  create mode 100644 include/drm/bridge/analogix_dp.h

_______________________________________________
dri-devel mailing list
dri-devel@xxxxxxxxxxxxxxxxxxxxx
http://lists.freedesktop.org/mailman/listinfo/dri-devel




[Index of Archives]     [Linux DRI Users]     [Linux Intel Graphics]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]
  Powered by Linux