On Wed, Dec 02, 2015 at 12:22:59PM +0000, Liviu Dudau wrote:
> Cc: Rob Herring <robh+dt@xxxxxxxxxx>
> Cc: Pawel Moll <pawel.moll@xxxxxxx>
> Cc: Mark Rutland <mark.rutland@xxxxxxx>
> Cc: Ian Campbell <ijc+devicetree@xxxxxxxxxxxxxx>
> Cc: Kumar Gala <galak@xxxxxxxxxxxxxx>
>
> Signed-off-by: Liviu Dudau <Liviu.Dudau@xxxxxxx>
I still think you should have a more specific compatible string, but
here's some rope:
Acked-by: Rob Herring <robh@xxxxxxxxxx>
> ---
> .../devicetree/bindings/display/arm,hdlcd.txt | 79 ++++++++++++++++++++++
> 1 file changed, 79 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/display/arm,hdlcd.txt
>
> diff --git a/Documentation/devicetree/bindings/display/arm,hdlcd.txt b/Documentation/devicetree/bindings/display/arm,hdlcd.txt
> new file mode 100644
> index 0000000..78bc242
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/display/arm,hdlcd.txt
> @@ -0,0 +1,79 @@
> +ARM HDLCD
> +
> +This is a display controller found on several development platforms produced
> +by ARM Ltd and in more modern of its' Fast Models. The HDLCD is an RGB
> +streamer that reads the data from a framebuffer and sends it to a single
> +digital encoder (DVI or HDMI).
> +
> +Required properties:
> + - compatible: "arm,hdlcd"
> + - reg: Physical base address and length of the controller's registers.
> + - interrupts: One interrupt used by the display controller to notify the
> + interrupt controller when any of the interrupt sources programmed in
> + the interrupt mask register have activated.
> + - clocks: A list of phandle + clock-specifier pairs, one for each
> + entry in 'clock-names'.
> + - clock-names: A list of clock names. For HDLCD it should contain:
> + - "pxlclk" for the clock feeding the output PLL of the controller.
> +
> +Required sub-nodes:
> + - port: The HDLCD connection to an encoder chip. The connection is modeled
> + using the OF graph bindings specified in
> + Documentation/devicetree/bindings/graph.txt.
> +
> +Optional properties:
> + - memory-region: phandle to a node describing memory (see
> + Documentation/devicetree/bindings/reserved-memory/reserved-memory.txt) to be
> + used for the framebuffer; if not present, the framebuffer may be located
> + anywhere in memory.
> +
> +
> +Example:
> +
> +/ {
> + ...
> +
> + hdlcd@2b000000 {
> + compatible = "arm,hdlcd";
> + reg = <0 0x2b000000 0 0x1000>;
> + interrupts = <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH>;
> + clocks = <&oscclk5>;
> + clock-names = "pxlclk";
> + port {
> + hdlcd_output: endpoint@0 {
> + remote-endpoint = <&hdmi_enc_input>;
> + };
> + };
> + };
> +
> + /* HDMI encoder on I2C bus */
> + i2c@7ffa0000 {
> + ....
> + hdmi-transmitter@70 {
> + compatible = ".....";
> + reg = <0x70>;
> + port@0 {
> + hdmi_enc_input: endpoint {
> + remote-endpoint = <&hdlcd_output>;
> + };
> +
> + hdmi_enc_output: endpoint {
> + remote-endpoint = <&hdmi_1_port>;
> + };
> + };
> + };
> +
> + };
> +
> + hdmi1: connector@1 {
> + compatible = "hdmi-connector";
> + type = "a";
> + port {
> + hdmi_1_port: endpoint {
> + remote-endpoint = <&hdmi_enc_output>;
> + };
> + };
> + };
> +
> + ...
> +};
> --
> 2.6.2
>
_______________________________________________
dri-devel mailing list
dri-devel@xxxxxxxxxxxxxxxxxxxxx
http://lists.freedesktop.org/mailman/listinfo/dri-devel
