On Thu, Aug 27, 2015 at 10:04:13AM -0700, Bob Paauwe wrote:
> Allow comma separated filenames in the edid_firmware parameter.
>
> For example:
>
> edid_firmware=eDP-1:edid/1280x480.bin,DP-2:edid/1920x1080.bin
>
> v2: Use strsep() to simplify parsing of comma seperated string. (Matt)
> Move initial bail before strdup. (Matt)
> v3: Changed conditionals after while loop to make more readable (Jani)
> Updated kernel-parameters.txt to reflect changes (Jani)
>
> Reviewed-by: Jani Nikula <jani.nikula@xxxxxxxxx>
> Reviewed-by: Matt Roper <matthew.d.roper@xxxxxxxxx>
> Signed-off-by: Bob Paauwe <bob.j.paauwe@xxxxxxxxx>
> ---
> Documentation/kernel-parameters.txt | 15 +++++++------
> drivers/gpu/drm/drm_edid_load.c | 42 ++++++++++++++++++++++++++++++-------
> 2 files changed, 43 insertions(+), 14 deletions(-)
>
> diff --git a/Documentation/kernel-parameters.txt b/Documentation/kernel-parameters.txt
> index cd03a0f..a0cab10 100644
> --- a/Documentation/kernel-parameters.txt
> +++ b/Documentation/kernel-parameters.txt
> @@ -915,11 +915,11 @@ bytes respectively. Such letter suffixes can also be entirely omitted.
> The filter can be disabled or changed to another
> driver later using sysfs.
>
> - drm_kms_helper.edid_firmware=[<connector>:]<file>
> - Broken monitors, graphic adapters and KVMs may
> - send no or incorrect EDID data sets. This parameter
> - allows to specify an EDID data set in the
> - /lib/firmware directory that is used instead.
> + drm_kms_helper.edid_firmware=[<connector>:]<file>[,[<connector>:]<file>]
> + Broken monitors, graphic adapters, KVMs and EDIDless
> + panels may send no or incorrect EDID data sets.
> + This parameter allows to specify an EDID data sets
> + in the /lib/firmware directory that are used instead.
> Generic built-in EDID data sets are used, if one of
> edid/1024x768.bin, edid/1280x1024.bin,
> edid/1680x1050.bin, or edid/1920x1080.bin is given
> @@ -928,7 +928,10 @@ bytes respectively. Such letter suffixes can also be entirely omitted.
> available in Documentation/EDID/HOWTO.txt. An EDID
> data set will only be used for a particular connector,
> if its name and a colon are prepended to the EDID
> - name.
> + name. Each connector may use a unique EDID data
> + set by separating the files with a comma. An EDID
> + data set with no connector name will be used for
> + any connectors not explicitly specified.
>
> dscc4.setup= [NET]
>
> diff --git a/drivers/gpu/drm/drm_edid_load.c b/drivers/gpu/drm/drm_edid_load.c
> index c5605fe..a203e154 100644
> --- a/drivers/gpu/drm/drm_edid_load.c
> +++ b/drivers/gpu/drm/drm_edid_load.c
> @@ -264,20 +264,44 @@ out:
> int drm_load_edid_firmware(struct drm_connector *connector)
> {
> const char *connector_name = connector->name;
> - char *edidname = edid_firmware, *last, *colon;
> + char *edidname, *last, *colon, *fwstr, *edidstr, *fallback = NULL;
> int ret;
> struct edid *edid;
>
> - if (*edidname == '\0')
> + if (edid_firmware[0] == '\0')
> return 0;
>
> - colon = strchr(edidname, ':');
> - if (colon != NULL) {
> - if (strncmp(connector_name, edidname, colon - edidname))
> - return 0;
> - edidname = colon + 1;
> - if (*edidname == '\0')
> + /*
> + * If there are multiple edid files specified and separated
> + * by commas, search through the list looking for one that
> + * matches the connector.
> + *
> + * If there's one or more that don't't specify a connector, keep
> + * the last one found one as a fallback.
> + */
> + fwstr = kstrdup(edid_firmware, GFP_KERNEL);
> + edidstr = fwstr;
> +
> + while ((edidname = strsep(&edidstr, ","))) {
> + colon = strchr(edidname, ':');
> + if (colon != NULL) {
> + if (strncmp(connector_name, edidname, colon-edidname))
> + continue;
> + edidname = colon + 1;
> + break;
> + } else {
> + if (*edidname != '\0') /* corner case: multiple ',' */
> + fallback = edidname;
> + }
I flattened the control flow here and done a few other checkpatch
appeasements. Merged to drm-misc, thanks.
-Daniel
> +
> + }
> +
> + if (!edidname) {
> + if (!fallback) {
> + kfree(fwstr);
> return 0;
> + }
> + edidname = fallback;
> }
>
> last = edidname + strlen(edidname) - 1;
> @@ -285,6 +309,8 @@ int drm_load_edid_firmware(struct drm_connector *connector)
> *last = '\0';
>
> edid = edid_load(connector, edidname, connector_name);
> + kfree(fwstr);
> +
> if (IS_ERR_OR_NULL(edid))
> return 0;
>
> --
> 2.1.0
>
> _______________________________________________
> dri-devel mailing list
> dri-devel@xxxxxxxxxxxxxxxxxxxxx
> http://lists.freedesktop.org/mailman/listinfo/dri-devel
--
Daniel Vetter
Software Engineer, Intel Corporation
http://blog.ffwll.ch
_______________________________________________
dri-devel mailing list
dri-devel@xxxxxxxxxxxxxxxxxxxxx
http://lists.freedesktop.org/mailman/listinfo/dri-devel
