On Fri, Aug 21, 2015 at 2:16 PM, <cpaul@xxxxxxxxxx> wrote:
> From: Stephen Chandler Paul <cpaul@xxxxxxxxxx>
>
> Most of the time this isn't an issue since hotplugging an adaptor will
> trigger a crtc mode change which in turn, causes the driver to probe
> every DisplayPort for a dpcd. However, in cases where hotplugging
> doesn't cause a mode change (specifically when one unplugs a monitor
> from a DisplayPort connector, then plugs that same monitor back in
> seconds later on the same port without any other monitors connected), we
> never probe for the dpcd before starting the initial link training. What
> happens from there looks like this:
>
> - GPU has only one monitor connected. It's connected via
> DisplayPort, and does not go through an adaptor of any sort.
>
> - User unplugs DisplayPort connector from GPU.
>
> - Change in HPD is detected by the driver, we probe every
> DisplayPort for a possible connection.
>
> - Probe the port the user originally had the monitor connected
> on for it's dpcd. This fails, and we clear the first (and only
> the first) byte of the dpcd to indicate we no longer have a
> dpcd for this port.
>
> - User plugs the previously disconnected monitor back into the
> same DisplayPort.
>
> - radeon_connector_hotplug() is called before everyone else,
> and tries to handle the link training. Since only the first
> byte of the dpcd is zeroed, the driver is able to complete
> link training but does so against the wrong dpcd, causing it
> to initialize the link with the wrong settings.
>
> - Display stays blank (usually), dpcd is probed after the
> initial link training, and the driver prints no obvious
> messages to the log.
>
> In theory, since only one byte of the dpcd is chopped off (specifically,
> the byte that contains the revision information for DisplayPort), it's
> not entirely impossible that this bug may not show on certain monitors.
> For instance, the only reason this bug was visible on my ASUS PB238
> monitor was due to the fact that this monitor using the enhanced framing
> symbol sequence, the flag for which is ignored if the radeon driver
> thinks that the DisplayPort version is below 1.1.
>
> Signed-off-by: Stephen Chandler Paul <cpaul@xxxxxxxxxx>
> Reviewed-by: Jerome Glisse <jglisse@xxxxxxxxxx>
Applied. thanks!
Alex
> ---
> drivers/gpu/drm/radeon/radeon_connectors.c | 5 +++++
> 1 file changed, 5 insertions(+)
>
> diff --git a/drivers/gpu/drm/radeon/radeon_connectors.c b/drivers/gpu/drm/radeon/radeon_connectors.c
> index 94b21ae..5a2cafb 100644
> --- a/drivers/gpu/drm/radeon/radeon_connectors.c
> +++ b/drivers/gpu/drm/radeon/radeon_connectors.c
> @@ -95,6 +95,11 @@ void radeon_connector_hotplug(struct drm_connector *connector)
> if (!radeon_hpd_sense(rdev, radeon_connector->hpd.hpd)) {
> drm_helper_connector_dpms(connector, DRM_MODE_DPMS_OFF);
> } else if (radeon_dp_needs_link_train(radeon_connector)) {
> + /* Don't try to start link training before we
> + * have the dpcd */
> + if (!radeon_dp_getdpcd(radeon_connector))
> + return;
> +
> /* set it to OFF so that drm_helper_connector_dpms()
> * won't return immediately since the current state
> * is ON at this point.
> --
> 2.4.3
>
> _______________________________________________
> dri-devel mailing list
> dri-devel@xxxxxxxxxxxxxxxxxxxxx
> http://lists.freedesktop.org/mailman/listinfo/dri-devel
_______________________________________________
dri-devel mailing list
dri-devel@xxxxxxxxxxxxxxxxxxxxx
http://lists.freedesktop.org/mailman/listinfo/dri-devel
