Re: [PATCH 5/5] drm/msm/mdp5: Add hardware configuration for msm8x16

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi,

> Hi,
>
> On 03/09/2015 06:41 PM, Stephane Viau wrote:
>> This change adds the hw configuration for msm8x16 chipsets in
>> mdp5_cfg module.
>>
>> Note that only one external display interface is present in this
>> configuration (DSI) but has not been enabled yet. It will be enabled
>> once drm/msm driver supports DSI connectors.
>>
>> Signed-off-by: Stephane Viau <sviau@xxxxxxxxxxxxxx>
>> ---
>>   drivers/gpu/drm/msm/mdp/mdp5/mdp5_cfg.c | 51
>> ++++++++++++++++++++++++++++++++-
>>   1 file changed, 50 insertions(+), 1 deletion(-)
>>
>> diff --git a/drivers/gpu/drm/msm/mdp/mdp5/mdp5_cfg.c
>> b/drivers/gpu/drm/msm/mdp/mdp5/mdp5_cfg.c
>> index 96ea6dd..9ff7ac1 100644
>> --- a/drivers/gpu/drm/msm/mdp/mdp5/mdp5_cfg.c
>> +++ b/drivers/gpu/drm/msm/mdp/mdp5/mdp5_cfg.c
>> @@ -1,5 +1,5 @@
>>   /*
>> - * Copyright (c) 2014 The Linux Foundation. All rights reserved.
>> + * Copyright (c) 2014-2015 The Linux Foundation. All rights reserved.
>>    *
>>    * This program is free software; you can redistribute it and/or
>> modify
>>    * it under the terms of the GNU General Public License version 2 and
>> @@ -150,10 +150,59 @@ const struct mdp5_cfg_hw apq8084_config = {
>>   	.max_clk = 320000000,
>>   };
>>
>> +const struct mdp5_cfg_hw msm8x16_config = {
>> +	.name = "msm8x16",
>> +	.mdp = {
>> +		.count = 1,
>> +		.base = { 0x01000 },
>> +	},
>> +	.smp = {
>> +		.mmb_count = 8,
>> +		.mmb_size = 8192,
>> +		.clients = {
>> +			[SSPP_VIG0] = 1, [SSPP_DMA0] = 4,
>> +			[SSPP_RGB0] = 7, [SSPP_RGB1] = 8,
>> +		},
>> +	},
>> +	.ctl = {
>> +		.count = 5,
>> +		.base = { 0x02000, 0x02200, 0x02400, 0x02600, 0x02800 },
>> +	},
>> +	.pipe_vig = {
>> +		.count = 1,
>> +		.base = { 0x05000 },
>> +	},
>> +	.pipe_rgb = {
>> +		.count = 2,
>> +		.base = { 0x15000, 0x17000 },
>> +	},
>> +	.pipe_dma = {
>> +		.count = 1,
>> +		.base = { 0x25000 },
>> +	},
>> +	.lm = {
>> +		.count = 2, /* LM0 and LM3 */
>> +		.base = { 0x45000, 0x48000 },
>> +		.nb_stages = 5,
>> +	},
>> +	.dspp = {
>> +		.count = 1,
>> +		.base = { 0x55000 },
>> +
>> +	},
>> +	.intf = {
>> +		.count = 1, /* INTF_1 */
>> +		.base = { 0x6B800 },
>
> We would need to put the other non-existent INTF_0, INTF_2 and INTF_3
> base addresses here too, so that the writes to
> REG_MDP5_INTF_TIMING_ENGINE_EN in the patch "Make the intf connection in
> config module" access the correct registers.

You are referring here to the discussion we had in "drm/msm/mdp5: Make the
intf connection in config module"[1]...

Let me clarify:
We see these faults when interfaces are *present* but not *supported* by
the driver, where:
 - *present* means that the interfaces are physically implemented in HW
and therefore need to be reflected by "intf.base" addresses
 - *supported* means that the msm KMS driver is actually able to drive an
interface
If you look at mdp5_cfg.c in "drm/msm/mdp5: Make the intf connection in
config module"[1], 4 interfaces (intf.base) are present (for apq8084), but
only 2 are supported (intfs[])...
What I meant is that even though our driver cannot support all interfaces
present in a chip, we still need to disable them in mdp5_kms_init().
(BTW, this is probably due to my bootloader enabling the DSI whereas the
msm KMS driver does not support it as of yet - and thus leads to
artifacts/underflow on my eDP panel.)

So to answer your comment, it doesn't make too much sense to define base
addresses for interfaces that are not present in a chip. Instead I'd
prefer to check if intf.base is not NULL before writing in
REG_MDP5_INTF_TIMING_ENGINE_EN registers.. and avoid some INVALID_INDEX
BUGs ;-).

I'm sending out a v3 for "drm/msm/mdp5: Make the intf connection in config
module" in a minute...

[1] http://lists.freedesktop.org/archives/dri-devel/2015-March/078651.html

>
> Archit
>
>> +	},
>> +	/* TODO enable .intfs[] with [1] = INTF_DSI, once DSI is implemented
>> */
>> +	.max_clk = 320000000,
>> +};
>> +
>>   static const struct mdp5_cfg_handler cfg_handlers[] = {
>>   	{ .revision = 0, .config = { .hw = &msm8x74_config } },
>>   	{ .revision = 2, .config = { .hw = &msm8x74_config } },
>>   	{ .revision = 3, .config = { .hw = &apq8084_config } },
>> +	{ .revision = 6, .config = { .hw = &msm8x16_config } },
>>   };
>>
>>
>>
>
> --
> Qualcomm Innovation Center, Inc. is a member of Code Aurora Forum,
> a Linux Foundation Collaborative Project
> --
> To unsubscribe from this list: send the line "unsubscribe linux-arm-msm"
> in
> the body of a message to majordomo@xxxxxxxxxxxxxxx
> More majordomo info at  http://vger.kernel.org/majordomo-info.html
>


-- 
Qualcomm Innovation Center, Inc.

The Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project

_______________________________________________
dri-devel mailing list
dri-devel@xxxxxxxxxxxxxxxxxxxxx
http://lists.freedesktop.org/mailman/listinfo/dri-devel





[Index of Archives]     [Linux DRI Users]     [Linux Intel Graphics]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]
  Powered by Linux