From: Lars-Peter Clausen <lars@xxxxxxxxxx>
This patch adds a driver for the Analog Devices adv7511. The adv7511 is
a standalone HDMI transmitter chip. It features a HDMI output interface
on one end and video and audio input interfaces on the other.
Signed-off-by: Lars-Peter Clausen <lars@xxxxxxxxxx>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@xxxxxxxxxxxxxxxx>
---
This commit incorporates the following commits.
DRM: adv7511: Sync to latest version
DRM: adv7511: Fix calculation and setting of CTS
DRM: adv7511: Write status word frequency and word len registers
adv7511: Remove some debug printks
Merge branch 'xcomm_zynq' into xcomm_zynq_3_5
Sync adv7511 and axi-hdmi driver to latest version
drm:adv7511: Re-add module information
DRM: adv7511: Don't use raw_edid to pass edid data
drm: adv7511: Ignore the csc scaling factor when the csc is disabled
drm: adv7511: Check if edid is NULL before duplicating it
drm: adv7511: Include the extension sections when duplicating the edid
DRM: adv7511: Work around off-by-one hardware bug
DRM: adv7511: Make embedded sync generator setup more robust
DRM: adv7511_audio: Fix typo
DRM: adv7511: Add powerdown gpio support
drm: adv7511: Fix use after free
DRM: adv7511: Properly initialize dpms_mode and status
DRM: adv7511: Avoid uneccessary disconnected events
drm: adv7511: Fix adv7511 encoder driver
drm: adv7511: Fix kernel-doc format
drm: adv7511: Fix adv7511_parse_dt()
drm: adv7511: Add the rgb format flag to adv7511_link_config
drm: adv7511: Configure CSC in adv7511_set_config()
drm: adv7511: Add adv7511_set_config_csc()
drm: adv7511: Configure the csc when getting modes
drm: adv7511: Add adv7511_encoder_mode_valid() function
drm: adv7511: Don't export adv7511_get_edid function
drm: adv7511: Mark the revision register as volatile
drm: adv7511: Initialize work queue before requesting IRQ
drm: adv7511: Remove trailing whitespaces
drm: adv7511: Remove audio support
drm: adv7511: Remove DRM slave encoder .set_config operation
drm: adv7511: Make the adv7511_packet_(enable|disable) functions static
drm: adv7511: Move Kconfig entry to drivers/gpu/drm/i2c/Kconfig
drm: adv7511: Update to the latest DRM API
drm: adv7511: Rename driver source file to adv7511.c
drm: adv7511: Add OF match table
drm: adv7511: Add ADV7513 support
drm: adv7511: Remove platform data support
drm: adv7511: Convert to the gpiod API
drm: adv7511: Remove packet and CEC I2C device support
drm: adv7511: Use the devm_ managed IRQ API
drm: adv7511: Remove unneeded local variable initialization
drm: adv7511: Pass the adv7511 pointer to adv7511_get_edid_block
drm: adv7511: Make loop counter unsigned
drm: adv7511: Pass adv7511 pointer to adv7511_set_config_csc function
drm: adv7511: Reorganize the code in sections
drm: adv7511: Simplify DT bindings
---
drivers/gpu/drm/i2c/Kconfig | 6 +
drivers/gpu/drm/i2c/Makefile | 2 +
drivers/gpu/drm/i2c/adv7511.c | 1007 +++++++++++++++++++++++++++++++++++++++++
drivers/gpu/drm/i2c/adv7511.h | 289 ++++++++++++
4 files changed, 1304 insertions(+)
create mode 100644 drivers/gpu/drm/i2c/adv7511.c
create mode 100644 drivers/gpu/drm/i2c/adv7511.h
diff --git a/drivers/gpu/drm/i2c/Kconfig b/drivers/gpu/drm/i2c/Kconfig
index 4d341db..22c7ed6 100644
--- a/drivers/gpu/drm/i2c/Kconfig
+++ b/drivers/gpu/drm/i2c/Kconfig
@@ -1,6 +1,12 @@
menu "I2C encoder or helper chips"
depends on DRM && DRM_KMS_HELPER && I2C
+config DRM_I2C_ADV7511
+ tristate "AV7511 encoder"
+ select REGMAP_I2C
+ help
+ Support for the Analog Device ADV7511(W) and ADV7513 HDMI encoders.
+
config DRM_I2C_CH7006
tristate "Chrontel ch7006 TV encoder"
default m if DRM_NOUVEAU
diff --git a/drivers/gpu/drm/i2c/Makefile b/drivers/gpu/drm/i2c/Makefile
index 43aa33b..2c72eb5 100644
--- a/drivers/gpu/drm/i2c/Makefile
+++ b/drivers/gpu/drm/i2c/Makefile
@@ -1,5 +1,7 @@
ccflags-y := -Iinclude/drm
+obj-$(CONFIG_DRM_I2C_ADV7511) += adv7511.o
+
ch7006-y := ch7006_drv.o ch7006_mode.o
obj-$(CONFIG_DRM_I2C_CH7006) += ch7006.o
diff --git a/drivers/gpu/drm/i2c/adv7511.c b/drivers/gpu/drm/i2c/adv7511.c
new file mode 100644
index 0000000..0a61a17
--- /dev/null
+++ b/drivers/gpu/drm/i2c/adv7511.c
@@ -0,0 +1,1007 @@
+/*
+ * Analog Devices ADV7511 HDMI transmitter driver
+ *
+ * Copyright 2012 Analog Devices Inc.
+ *
+ * Licensed under the GPL-2.
+ */
+
+#include <linux/device.h>
+#include <linux/gpio/consumer.h>
+#include <linux/i2c.h>
+#include <linux/module.h>
+#include <linux/regmap.h>
+#include <linux/slab.h>
+
+#include <drm/drmP.h>
+#include <drm/drm_crtc_helper.h>
+#include <drm/drm_edid.h>
+#include <drm/drm_encoder_slave.h>
+
+#include "adv7511.h"
+
+struct adv7511 {
+ struct i2c_client *i2c_main;
+ struct i2c_client *i2c_edid;
+
+ struct regmap *regmap;
+ struct regmap *packet_memory_regmap;
+ enum drm_connector_status status;
+ int dpms_mode;
+
+ unsigned int f_tmds;
+
+ unsigned int current_edid_segment;
+ uint8_t edid_buf[256];
+
+ wait_queue_head_t wq;
+ struct drm_encoder *encoder;
+
+ bool embedded_sync;
+ enum adv7511_sync_polarity vsync_polarity;
+ enum adv7511_sync_polarity hsync_polarity;
+ bool rgb;
+
+ struct edid *edid;
+
+ struct gpio_desc *gpio_pd;
+};
+
+static struct adv7511 *encoder_to_adv7511(struct drm_encoder *encoder)
+{
+ return to_encoder_slave(encoder)->slave_priv;
+}
+
+/* ADI recommanded values for proper operation. */
+static const struct reg_default adv7511_fixed_registers[] = {
+ { 0x98, 0x03 },
+ { 0x9a, 0xe0 },
+ { 0x9c, 0x30 },
+ { 0x9d, 0x61 },
+ { 0xa2, 0xa4 },
+ { 0xa3, 0xa4 },
+ { 0xe0, 0xd0 },
+ { 0xf9, 0x00 },
+ { 0x55, 0x02 },
+};
+
+/* -----------------------------------------------------------------------------
+ * Register access
+ */
+
+static const uint8_t adv7511_register_defaults[] = {
+ 0x12, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, /* 00 */
+ 0x00, 0x00, 0x01, 0x0e, 0xbc, 0x18, 0x01, 0x13,
+ 0x25, 0x37, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, /* 10 */
+ 0x46, 0x62, 0x04, 0xa8, 0x00, 0x00, 0x1c, 0x84,
+ 0x1c, 0xbf, 0x04, 0xa8, 0x1e, 0x70, 0x02, 0x1e, /* 20 */
+ 0x00, 0x00, 0x04, 0xa8, 0x08, 0x12, 0x1b, 0xac,
+ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, /* 30 */
+ 0x00, 0x00, 0x00, 0x80, 0x00, 0x00, 0x00, 0xb0,
+ 0x00, 0x50, 0x90, 0x7e, 0x79, 0x70, 0x00, 0x00, /* 40 */
+ 0x00, 0xa8, 0x80, 0x00, 0x00, 0x00, 0x00, 0x00,
+ 0x00, 0x00, 0x02, 0x0d, 0x00, 0x00, 0x00, 0x00, /* 50 */
+ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, /* 60 */
+ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+ 0x01, 0x0a, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, /* 70 */
+ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, /* 80 */
+ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+ 0x00, 0x00, 0x00, 0x00, 0xc0, 0x00, 0x00, 0x00, /* 90 */
+ 0x0b, 0x02, 0x00, 0x18, 0x5a, 0x60, 0x00, 0x00,
+ 0x00, 0x00, 0x80, 0x80, 0x08, 0x04, 0x00, 0x00, /* a0 */
+ 0x00, 0x00, 0x00, 0x40, 0x00, 0x00, 0x40, 0x14,
+ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, /* b0 */
+ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, /* c0 */
+ 0x00, 0x03, 0x00, 0x00, 0x02, 0x00, 0x01, 0x04,
+ 0x30, 0xff, 0x80, 0x80, 0x80, 0x00, 0x00, 0x00, /* d0 */
+ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x10, 0x01,
+ 0x80, 0x75, 0x00, 0x00, 0x60, 0x00, 0x00, 0x00, /* e0 */
+ 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+ 0x00, 0x00, 0x00, 0x00, 0x00, 0x75, 0x11, 0x00, /* f0 */
+ 0x00, 0x7c, 0x00, 0x00, 0x00, 0x00, 0x00, 0x00,
+};
+
+static bool adv7511_register_volatile(struct device *dev, unsigned int reg)
+{
+ switch (reg) {
+ case ADV7511_REG_CHIP_REVISION:
+ case ADV7511_REG_SPDIF_FREQ:
+ case ADV7511_REG_CTS_AUTOMATIC1:
+ case ADV7511_REG_CTS_AUTOMATIC2:
+ case ADV7511_REG_VIC_DETECTED:
+ case ADV7511_REG_VIC_SEND:
+ case ADV7511_REG_AUX_VIC_DETECTED:
+ case ADV7511_REG_STATUS:
+ case ADV7511_REG_GC(1):
+ case ADV7511_REG_INT(0):
+ case ADV7511_REG_INT(1):
+ case ADV7511_REG_PLL_STATUS:
+ case ADV7511_REG_AN(0):
+ case ADV7511_REG_AN(1):
+ case ADV7511_REG_AN(2):
+ case ADV7511_REG_AN(3):
+ case ADV7511_REG_AN(4):
+ case ADV7511_REG_AN(5):
+ case ADV7511_REG_AN(6):
+ case ADV7511_REG_AN(7):
+ case ADV7511_REG_HDCP_STATUS:
+ case ADV7511_REG_BCAPS:
+ case ADV7511_REG_BKSV(0):
+ case ADV7511_REG_BKSV(1):
+ case ADV7511_REG_BKSV(2):
+ case ADV7511_REG_BKSV(3):
+ case ADV7511_REG_BKSV(4):
+ case ADV7511_REG_DDC_STATUS:
+ case ADV7511_REG_BSTATUS(0):
+ case ADV7511_REG_BSTATUS(1):
+ case ADV7511_REG_CHIP_ID_HIGH:
+ case ADV7511_REG_CHIP_ID_LOW:
+ return true;
+ }
+
+ return false;
+}
+
+static const struct regmap_config adv7511_regmap_config = {
+ .reg_bits = 8,
+ .val_bits = 8,
+
+ .max_register = 0xff,
+ .cache_type = REGCACHE_RBTREE,
+ .reg_defaults_raw = adv7511_register_defaults,
+ .num_reg_defaults_raw = ARRAY_SIZE(adv7511_register_defaults),
+
+ .volatile_reg = adv7511_register_volatile,
+};
+
+/* -----------------------------------------------------------------------------
+ * Hardware configuration
+ */
+
+static void adv7511_set_colormap(struct adv7511 *adv7511, bool enable,
+ const uint16_t *coeff,
+ unsigned int scaling_factor)
+{
+ unsigned int i;
+
+ regmap_update_bits(adv7511->regmap, ADV7511_REG_CSC_UPPER(1),
+ ADV7511_CSC_UPDATE_MODE, ADV7511_CSC_UPDATE_MODE);
+
+ if (enable) {
+ for (i = 0; i < 12; ++i) {
+ regmap_update_bits(adv7511->regmap,
+ ADV7511_REG_CSC_UPPER(i),
+ 0x1f, coeff[i] >> 8);
+ regmap_write(adv7511->regmap,
+ ADV7511_REG_CSC_LOWER(i),
+ coeff[i] & 0xff);
+ }
+ }
+
+ if (enable)
+ regmap_update_bits(adv7511->regmap, ADV7511_REG_CSC_UPPER(0),
+ 0xe0, 0x80 | (scaling_factor << 5));
+ else
+ regmap_update_bits(adv7511->regmap, ADV7511_REG_CSC_UPPER(0),
+ 0x80, 0x00);
+
+ regmap_update_bits(adv7511->regmap, ADV7511_REG_CSC_UPPER(1),
+ ADV7511_CSC_UPDATE_MODE, 0);
+}
+
+static int adv7511_packet_enable(struct adv7511 *adv7511, unsigned int packet)
+{
+ if (packet & 0xff)
+ regmap_update_bits(adv7511->regmap, ADV7511_REG_PACKET_ENABLE0,
+ packet, 0xff);
+
+ if (packet & 0xff00) {
+ packet >>= 8;
+ regmap_update_bits(adv7511->regmap, ADV7511_REG_PACKET_ENABLE1,
+ packet, 0xff);
+ }
+
+ return 0;
+}
+
+static int adv7511_packet_disable(struct adv7511 *adv7511, unsigned int packet)
+{
+ if (packet & 0xff)
+ regmap_update_bits(adv7511->regmap, ADV7511_REG_PACKET_ENABLE0,
+ packet, 0x00);
+
+ if (packet & 0xff00) {
+ packet >>= 8;
+ regmap_update_bits(adv7511->regmap, ADV7511_REG_PACKET_ENABLE1,
+ packet, 0x00);
+ }
+
+ return 0;
+}
+
+/* Coefficients for adv7511 color space conversion */
+static const uint16_t adv7511_csc_ycbcr_to_rgb[] = {
+ 0x0734, 0x04ad, 0x0000, 0x1c1b,
+ 0x1ddc, 0x04ad, 0x1f24, 0x0135,
+ 0x0000, 0x04ad, 0x087c, 0x1b77,
+};
+
+static void adv7511_set_config_csc(struct adv7511 *adv7511,
+ struct drm_connector *connector,
+ bool rgb)
+{
+ struct adv7511_video_config config;
+ bool output_format_422, output_format_ycbcr;
+ unsigned int mode;
+ uint8_t infoframe[17];
+
+ if (adv7511->edid)
+ config.hdmi_mode = drm_detect_hdmi_monitor(adv7511->edid);
+ else
+ config.hdmi_mode = false;
+
+ hdmi_avi_infoframe_init(&config.avi_infoframe);
+
+ config.avi_infoframe.scan_mode = HDMI_SCAN_MODE_UNDERSCAN;
+
+ if (rgb) {
+ config.csc_enable = false;
+ config.avi_infoframe.colorspace = HDMI_COLORSPACE_RGB;
+ } else {
+ config.csc_scaling_factor = ADV7511_CSC_SCALING_4;
+ config.csc_coefficents = adv7511_csc_ycbcr_to_rgb;
+
+ if ((connector->display_info.color_formats &
+ DRM_COLOR_FORMAT_YCRCB422) &&
+ config.hdmi_mode) {
+ config.csc_enable = false;
+ config.avi_infoframe.colorspace =
+ HDMI_COLORSPACE_YUV422;
+ } else {
+ config.csc_enable = true;
+ config.avi_infoframe.colorspace = HDMI_COLORSPACE_RGB;
+ }
+ }
+
+ if (config.hdmi_mode) {
+ mode = ADV7511_HDMI_CFG_MODE_HDMI;
+
+ switch (config.avi_infoframe.colorspace) {
+ case HDMI_COLORSPACE_YUV444:
+ output_format_422 = false;
+ output_format_ycbcr = true;
+ break;
+ case HDMI_COLORSPACE_YUV422:
+ output_format_422 = true;
+ output_format_ycbcr = true;
+ break;
+ default:
+ output_format_422 = false;
+ output_format_ycbcr = false;
+ break;
+ }
+ } else {
+ mode = ADV7511_HDMI_CFG_MODE_DVI;
+ output_format_422 = false;
+ output_format_ycbcr = false;
+ }
+
+ adv7511_packet_disable(adv7511, ADV7511_PACKET_ENABLE_AVI_INFOFRAME);
+
+ adv7511_set_colormap(adv7511, config.csc_enable,
+ config.csc_coefficents,
+ config.csc_scaling_factor);
+
+ regmap_update_bits(adv7511->regmap, ADV7511_REG_VIDEO_INPUT_CFG1, 0x81,
+ (output_format_422 << 7) | output_format_ycbcr);
+
+ regmap_update_bits(adv7511->regmap, ADV7511_REG_HDCP_HDMI_CFG,
+ ADV7511_HDMI_CFG_MODE_MASK, mode);
+
+ hdmi_avi_infoframe_pack(&config.avi_infoframe, infoframe,
+ sizeof(infoframe));
+
+ /* The AVI infoframe id is not configurable */
+ regmap_bulk_write(adv7511->regmap, ADV7511_REG_AVI_INFOFRAME_VERSION,
+ infoframe + 1, sizeof(infoframe) - 1);
+
+ adv7511_packet_enable(adv7511, ADV7511_PACKET_ENABLE_AVI_INFOFRAME);
+}
+
+static void adv7511_set_link_config(struct adv7511 *adv7511,
+ const struct adv7511_link_config *config)
+{
+ unsigned int clock_delay;
+ unsigned int color_depth;
+ unsigned int input_style;
+ unsigned int input_id;
+
+ clock_delay = (config->clock_delay + 1200) / 400;
+ color_depth = config->input_color_depth == 8 ? 3
+ : (config->input_color_depth == 10 ? 1 : 2);
+
+ input_style = config->input_style == 1 ? 2
+ : (config->input_style == 2 ? 1 : 3);
+
+ /* TODO Support input ID 6 */
+ if (config->input_colorspace != HDMI_COLORSPACE_YUV422)
+ input_id = config->input_clock == ADV7511_INPUT_CLOCK_DDR
+ ? 5 : 0;
+ else if (config->input_clock == ADV7511_INPUT_CLOCK_DDR)
+ input_id = config->embedded_sync ? 8 : 7;
+ else if (config->input_clock == ADV7511_INPUT_CLOCK_2X)
+ input_id = config->embedded_sync ? 4 : 3;
+ else
+ input_id = config->embedded_sync ? 2 : 1;
+
+ regmap_update_bits(adv7511->regmap, ADV7511_REG_I2C_FREQ_ID_CFG, 0xf,
+ input_id);
+ regmap_update_bits(adv7511->regmap, ADV7511_REG_VIDEO_INPUT_CFG1, 0x7e,
+ (color_depth << 4) | (input_style << 2));
+ regmap_write(adv7511->regmap, ADV7511_REG_VIDEO_INPUT_CFG2,
+ config->input_justification << 3);
+ regmap_write(adv7511->regmap, ADV7511_REG_TIMING_GEN_SEQ,
+ config->sync_pulse << 2);
+
+ regmap_write(adv7511->regmap, 0xba, clock_delay << 5);
+
+ adv7511->embedded_sync = config->embedded_sync;
+ adv7511->hsync_polarity = config->hsync_polarity;
+ adv7511->vsync_polarity = config->vsync_polarity;
+ adv7511->rgb = config->input_colorspace == HDMI_COLORSPACE_RGB;
+}
+
+/* -----------------------------------------------------------------------------
+ * Interrupt and hotplug detection
+ */
+
+static bool adv7511_hpd(struct adv7511 *adv7511)
+{
+ unsigned int irq0;
+ int ret;
+
+ ret = regmap_read(adv7511->regmap, ADV7511_REG_INT(0), &irq0);
+ if (ret < 0)
+ return false;
+
+ if (irq0 & ADV7511_INT0_HDP) {
+ regmap_write(adv7511->regmap, ADV7511_REG_INT(0),
+ ADV7511_INT0_HDP);
+ return true;
+ }
+
+ return false;
+}
+
+static irqreturn_t adv7511_irq_handler(int irq, void *devid)
+{
+ struct adv7511 *adv7511 = devid;
+
+ if (adv7511_hpd(adv7511))
+ drm_helper_hpd_irq_event(adv7511->encoder->dev);
+
+ wake_up_all(&adv7511->wq);
+
+ return IRQ_HANDLED;
+}
+
+static unsigned int adv7511_is_interrupt_pending(struct adv7511 *adv7511,
+ unsigned int irq)
+{
+ unsigned int irq0, irq1;
+ unsigned int pending;
+ int ret;
+
+ ret = regmap_read(adv7511->regmap, ADV7511_REG_INT(0), &irq0);
+ if (ret < 0)
+ return 0;
+ ret = regmap_read(adv7511->regmap, ADV7511_REG_INT(1), &irq1);
+ if (ret < 0)
+ return 0;
+
+ pending = (irq1 << 8) | irq0;
+
+ return pending & irq;
+}
+
+static int adv7511_wait_for_interrupt(struct adv7511 *adv7511, int irq,
+ int timeout)
+{
+ unsigned int pending;
+ int ret;
+
+ if (adv7511->i2c_main->irq) {
+ ret = wait_event_interruptible_timeout(adv7511->wq,
+ adv7511_is_interrupt_pending(adv7511, irq),
+ msecs_to_jiffies(timeout));
+ if (ret <= 0)
+ return 0;
+ pending = adv7511_is_interrupt_pending(adv7511, irq);
+ } else {
+ if (timeout < 25)
+ timeout = 25;
+ do {
+ pending = adv7511_is_interrupt_pending(adv7511, irq);
+ if (pending)
+ break;
+ msleep(25);
+ timeout -= 25;
+ } while (timeout >= 25);
+ }
+
+ return pending;
+}
+
+/* -----------------------------------------------------------------------------
+ * EDID retrieval
+ */
+
+static int adv7511_get_edid_block(void *data, u8 *buf, unsigned int block,
+ size_t len)
+{
+ struct adv7511 *adv7511 = data;
+ struct i2c_msg xfer[2];
+ uint8_t offset;
+ unsigned int i;
+ int ret;
+
+ if (len > 128)
+ return -EINVAL;
+
+ if (adv7511->current_edid_segment != block / 2) {
+ unsigned int status;
+
+ ret = regmap_read(adv7511->regmap, ADV7511_REG_DDC_STATUS,
+ &status);
+ if (ret < 0)
+ return ret;
+
+ if (status != 2) {
+ regmap_write(adv7511->regmap, ADV7511_REG_EDID_SEGMENT,
+ block);
+ ret = adv7511_wait_for_interrupt(adv7511,
+ ADV7511_INT0_EDID_READY |
+ ADV7511_INT1_DDC_ERROR, 200);
+
+ if (!(ret & ADV7511_INT0_EDID_READY))
+ return -EIO;
+ }
+
+ regmap_write(adv7511->regmap, ADV7511_REG_INT(0),
+ ADV7511_INT0_EDID_READY | ADV7511_INT1_DDC_ERROR);
+
+ /* Break this apart, hopefully more I2C controllers will
+ * support 64 byte transfers than 256 byte transfers
+ */
+
+ xfer[0].addr = adv7511->i2c_edid->addr;
+ xfer[0].flags = 0;
+ xfer[0].len = 1;
+ xfer[0].buf = &offset;
+ xfer[1].addr = adv7511->i2c_edid->addr;
+ xfer[1].flags = I2C_M_RD;
+ xfer[1].len = 64;
+ xfer[1].buf = adv7511->edid_buf;
+
+ offset = 0;
+
+ for (i = 0; i < 4; ++i) {
+ ret = i2c_transfer(adv7511->i2c_edid->adapter, xfer,
+ ARRAY_SIZE(xfer));
+ if (ret < 0)
+ return ret;
+ else if (ret != 2)
+ return -EIO;
+
+ xfer[1].buf += 64;
+ offset += 64;
+ }
+
+ adv7511->current_edid_segment = block / 2;
+ }
+
+ if (block % 2 == 0)
+ memcpy(buf, adv7511->edid_buf, len);
+ else
+ memcpy(buf, adv7511->edid_buf + 128, len);
+
+ return 0;
+}
+
+/* -----------------------------------------------------------------------------
+ * Encoder operations
+ */
+
+static int adv7511_get_modes(struct drm_encoder *encoder,
+ struct drm_connector *connector)
+{
+ struct adv7511 *adv7511 = encoder_to_adv7511(encoder);
+ struct edid *edid;
+ unsigned int count;
+
+ /* Reading the EDID only works if the device is powered */
+ if (adv7511->dpms_mode != DRM_MODE_DPMS_ON) {
+ regmap_write(adv7511->regmap, ADV7511_REG_INT(0),
+ ADV7511_INT0_EDID_READY | ADV7511_INT1_DDC_ERROR);
+ regmap_update_bits(adv7511->regmap, ADV7511_REG_POWER,
+ ADV7511_POWER_POWER_DOWN, 0);
+ adv7511->current_edid_segment = -1;
+ }
+
+ edid = drm_do_get_edid(connector, adv7511_get_edid_block, adv7511);
+
+ if (adv7511->dpms_mode != DRM_MODE_DPMS_ON)
+ regmap_update_bits(adv7511->regmap, ADV7511_REG_POWER,
+ ADV7511_POWER_POWER_DOWN,
+ ADV7511_POWER_POWER_DOWN);
+
+ kfree(adv7511->edid);
+ adv7511->edid = edid;
+ if (!edid)
+ return 0;
+
+ drm_mode_connector_update_edid_property(connector, edid);
+ count = drm_add_edid_modes(connector, edid);
+
+ adv7511_set_config_csc(adv7511, connector, adv7511->rgb);
+
+ return count;
+}
+
+static void adv7511_encoder_dpms(struct drm_encoder *encoder, int mode)
+{
+ struct adv7511 *adv7511 = encoder_to_adv7511(encoder);
+
+ switch (mode) {
+ case DRM_MODE_DPMS_ON:
+ adv7511->current_edid_segment = -1;
+
+ regmap_write(adv7511->regmap, ADV7511_REG_INT(0),
+ ADV7511_INT0_EDID_READY | ADV7511_INT1_DDC_ERROR);
+ regmap_update_bits(adv7511->regmap, ADV7511_REG_POWER,
+ ADV7511_POWER_POWER_DOWN, 0);
+ /*
+ * Per spec it is allowed to pulse the HDP signal to indicate
+ * that the EDID information has changed. Some monitors do this
+ * when they wakeup from standby or are enabled. When the HDP
+ * goes low the adv7511 is reset and the outputs are disabled
+ * which might cause the monitor to go to standby again. To
+ * avoid this we ignore the HDP pin for the first few seconds
+ * after enabeling the output.
+ */
+ regmap_update_bits(adv7511->regmap, ADV7511_REG_POWER2,
+ ADV7511_REG_POWER2_HDP_SRC_MASK,
+ ADV7511_REG_POWER2_HDP_SRC_NONE);
+ /* Most of the registers are reset during power down or
+ * when HPD is low
+ */
+ regcache_sync(adv7511->regmap);
+ break;
+ default:
+ /* TODO: setup additional power down modes */
+ regmap_update_bits(adv7511->regmap, ADV7511_REG_POWER,
+ ADV7511_POWER_POWER_DOWN,
+ ADV7511_POWER_POWER_DOWN);
+ regcache_mark_dirty(adv7511->regmap);
+ break;
+ }
+
+ adv7511->dpms_mode = mode;
+}
+
+static enum drm_connector_status
+adv7511_encoder_detect(struct drm_encoder *encoder,
+ struct drm_connector *connector)
+{
+ struct adv7511 *adv7511 = encoder_to_adv7511(encoder);
+ enum drm_connector_status status;
+ unsigned int val;
+ bool hpd;
+ int ret;
+
+ ret = regmap_read(adv7511->regmap, ADV7511_REG_STATUS, &val);
+ if (ret < 0)
+ return connector_status_disconnected;
+
+ if (val & ADV7511_STATUS_HPD)
+ status = connector_status_connected;
+ else
+ status = connector_status_disconnected;
+
+ hpd = adv7511_hpd(adv7511);
+
+ /* The chip resets itself when the cable is disconnected, so in case
+ * there is a pending HPD interrupt and the cable is connected there was
+ * at least one transition from disconnected to connected and the chip
+ * has to be reinitialized. */
+ if (status == connector_status_connected && hpd &&
+ adv7511->dpms_mode == DRM_MODE_DPMS_ON) {
+ regcache_mark_dirty(adv7511->regmap);
+ adv7511_encoder_dpms(encoder, adv7511->dpms_mode);
+ adv7511_get_modes(encoder, connector);
+ if (adv7511->status == connector_status_connected)
+ status = connector_status_disconnected;
+ } else {
+ /* Renable HDP sensing */
+ regmap_update_bits(adv7511->regmap, ADV7511_REG_POWER2,
+ ADV7511_REG_POWER2_HDP_SRC_MASK,
+ ADV7511_REG_POWER2_HDP_SRC_BOTH);
+ }
+
+ adv7511->status = status;
+ return status;
+}
+
+static int adv7511_encoder_mode_valid(struct drm_encoder *encoder,
+ struct drm_display_mode *mode)
+{
+ if (mode->clock > 165000)
+ return MODE_CLOCK_HIGH;
+
+ if (mode->flags & DRM_MODE_FLAG_INTERLACE)
+ return MODE_NO_INTERLACE;
+
+ return MODE_OK;
+}
+
+static void adv7511_encoder_mode_set(struct drm_encoder *encoder,
+ struct drm_display_mode *mode,
+ struct drm_display_mode *adj_mode)
+{
+ struct adv7511 *adv7511 = encoder_to_adv7511(encoder);
+ unsigned int low_refresh_rate;
+ unsigned int hsync_polarity = 0;
+ unsigned int vsync_polarity = 0;
+
+ if (adv7511->embedded_sync) {
+ unsigned int hsync_offset, hsync_len;
+ unsigned int vsync_offset, vsync_len;
+
+ hsync_offset = adj_mode->crtc_hsync_start -
+ adj_mode->crtc_hdisplay;
+ vsync_offset = adj_mode->crtc_vsync_start -
+ adj_mode->crtc_vdisplay;
+ hsync_len = adj_mode->crtc_hsync_end -
+ adj_mode->crtc_hsync_start;
+ vsync_len = adj_mode->crtc_vsync_end -
+ adj_mode->crtc_vsync_start;
+
+ /* The hardware vsync generator has a off-by-one bug */
+ vsync_offset += 1;
+
+ regmap_write(adv7511->regmap, ADV7511_REG_HSYNC_PLACEMENT_MSB,
+ ((hsync_offset >> 10) & 0x7) << 5);
+ regmap_write(adv7511->regmap, ADV7511_REG_SYNC_DECODER(0),
+ (hsync_offset >> 2) & 0xff);
+ regmap_write(adv7511->regmap, ADV7511_REG_SYNC_DECODER(1),
+ ((hsync_offset & 0x3) << 6) |
+ ((hsync_len >> 4) & 0x3f));
+ regmap_write(adv7511->regmap, ADV7511_REG_SYNC_DECODER(2),
+ ((hsync_len & 0xf) << 4) |
+ ((vsync_offset >> 6) & 0xf));
+ regmap_write(adv7511->regmap, ADV7511_REG_SYNC_DECODER(3),
+ ((vsync_offset & 0x3f) << 2) |
+ ((vsync_len >> 8) & 0x3));
+ regmap_write(adv7511->regmap, ADV7511_REG_SYNC_DECODER(4),
+ vsync_len & 0xff);
+
+ hsync_polarity = !(adj_mode->flags & DRM_MODE_FLAG_PHSYNC);
+ vsync_polarity = !(adj_mode->flags & DRM_MODE_FLAG_PVSYNC);
+ } else {
+ enum adv7511_sync_polarity mode_hsync_polarity;
+ enum adv7511_sync_polarity mode_vsync_polarity;
+
+ /**
+ * If the input signal is always low or always high we want to
+ * invert or let it passthrough depending on the polarity of the
+ * current mode.
+ **/
+ if (adj_mode->flags & DRM_MODE_FLAG_NHSYNC)
+ mode_hsync_polarity = ADV7511_SYNC_POLARITY_LOW;
+ else
+ mode_hsync_polarity = ADV7511_SYNC_POLARITY_HIGH;
+
+ if (adj_mode->flags & DRM_MODE_FLAG_NVSYNC)
+ mode_vsync_polarity = ADV7511_SYNC_POLARITY_LOW;
+ else
+ mode_vsync_polarity = ADV7511_SYNC_POLARITY_HIGH;
+
+ if (adv7511->hsync_polarity != mode_hsync_polarity &&
+ adv7511->hsync_polarity !=
+ ADV7511_SYNC_POLARITY_PASSTHROUGH)
+ hsync_polarity = 1;
+
+ if (adv7511->vsync_polarity != mode_vsync_polarity &&
+ adv7511->vsync_polarity !=
+ ADV7511_SYNC_POLARITY_PASSTHROUGH)
+ vsync_polarity = 1;
+ }
+
+ if (mode->vrefresh <= 24000)
+ low_refresh_rate = ADV7511_LOW_REFRESH_RATE_24HZ;
+ else if (mode->vrefresh <= 25000)
+ low_refresh_rate = ADV7511_LOW_REFRESH_RATE_25HZ;
+ else if (mode->vrefresh <= 30000)
+ low_refresh_rate = ADV7511_LOW_REFRESH_RATE_30HZ;
+ else
+ low_refresh_rate = ADV7511_LOW_REFRESH_RATE_NONE;
+
+ regmap_update_bits(adv7511->regmap, 0xfb,
+ 0x6, low_refresh_rate << 1);
+ regmap_update_bits(adv7511->regmap, 0x17,
+ 0x60, (vsync_polarity << 6) | (hsync_polarity << 5));
+
+ /*
+ * TODO Test first order 4:2:2 to 4:4:4 up conversion method, which is
+ * supposed to give better results.
+ */
+
+ adv7511->f_tmds = mode->clock;
+}
+
+static struct drm_encoder_slave_funcs adv7511_encoder_funcs = {
+ .dpms = adv7511_encoder_dpms,
+ .mode_valid = adv7511_encoder_mode_valid,
+ .mode_set = adv7511_encoder_mode_set,
+ .detect = adv7511_encoder_detect,
+ .get_modes = adv7511_get_modes,
+};
+
+/* -----------------------------------------------------------------------------
+ * Probe & remove
+ */
+
+static int adv7511_parse_dt(struct device_node *np,
+ struct adv7511_link_config *config)
+{
+ const char *str;
+ int ret;
+
+ memset(config, 0, sizeof(*config));
+
+ of_property_read_u32(np, "adi,input-depth", &config->input_color_depth);
+ if (config->input_color_depth != 8 && config->input_color_depth != 10 &&
+ config->input_color_depth != 12)
+ return -EINVAL;
+
+ ret = of_property_read_string(np, "adi,input-colorspace", &str);
+ if (ret < 0)
+ return ret;
+
+ if (!strcmp(str, "rgb"))
+ config->input_colorspace = HDMI_COLORSPACE_RGB;
+ else if (!strcmp(str, "yuv422"))
+ config->input_colorspace = HDMI_COLORSPACE_YUV422;
+ else if (!strcmp(str, "yuv444"))
+ config->input_colorspace = HDMI_COLORSPACE_YUV444;
+ else
+ return -EINVAL;
+
+ ret = of_property_read_string(np, "adi,input-clock", &str);
+ if (ret < 0)
+ return ret;
+
+ if (!strcmp(str, "1x"))
+ config->input_clock = ADV7511_INPUT_CLOCK_1X;
+ else if (!strcmp(str, "2x"))
+ config->input_clock = ADV7511_INPUT_CLOCK_2X;
+ else if (!strcmp(str, "ddr"))
+ config->input_clock = ADV7511_INPUT_CLOCK_DDR;
+ else
+ return -EINVAL;
+
+ if (config->input_colorspace == HDMI_COLORSPACE_YUV422 ||
+ config->input_clock != ADV7511_INPUT_CLOCK_1X) {
+ ret = of_property_read_u32(np, "adi,input-style",
+ &config->input_style);
+ if (ret)
+ return ret;
+
+ if (config->input_style < 1 || config->input_style > 3)
+ return -EINVAL;
+
+ ret = of_property_read_string(np, "adi,input-justification",
+ &str);
+ if (ret < 0)
+ return ret;
+
+ if (!strcmp(str, "left"))
+ config->input_justification =
+ ADV7511_INPUT_JUSTIFICATION_LEFT;
+ else if (!strcmp(str, "evenly"))
+ config->input_justification =
+ ADV7511_INPUT_JUSTIFICATION_EVENLY;
+ else if (!strcmp(str, "right"))
+ config->input_justification =
+ ADV7511_INPUT_JUSTIFICATION_RIGHT;
+ else
+ return -EINVAL;
+
+ } else {
+ config->input_style = 1;
+ config->input_justification = ADV7511_INPUT_JUSTIFICATION_LEFT;
+ }
+
+ of_property_read_u32(np, "adi,clock-delay", &config->clock_delay);
+ if (config->clock_delay < -1200 || config->clock_delay > 1600)
+ return -EINVAL;
+
+ config->embedded_sync = of_property_read_bool(np, "adi,embedded-sync");
+
+ /* Hardcode the sync pulse configurations for now. */
+ config->sync_pulse = ADV7511_INPUT_SYNC_PULSE_NONE;
+ config->vsync_polarity = ADV7511_SYNC_POLARITY_PASSTHROUGH;
+ config->hsync_polarity = ADV7511_SYNC_POLARITY_PASSTHROUGH;
+
+ return 0;
+}
+
+static const int edid_i2c_addr = 0x7e;
+static const int packet_i2c_addr = 0x70;
+static const int cec_i2c_addr = 0x78;
+
+static int adv7511_probe(struct i2c_client *i2c, const struct i2c_device_id *id)
+{
+ struct adv7511_link_config link_config;
+ struct adv7511 *adv7511;
+ struct device *dev = &i2c->dev;
+ unsigned int val;
+ int ret;
+
+ if (!dev->of_node)
+ return -EINVAL;
+
+ adv7511 = devm_kzalloc(dev, sizeof(*adv7511), GFP_KERNEL);
+ if (!adv7511)
+ return -ENOMEM;
+
+ adv7511->dpms_mode = DRM_MODE_DPMS_OFF;
+ adv7511->status = connector_status_disconnected;
+
+ ret = adv7511_parse_dt(dev->of_node, &link_config);
+ if (ret)
+ return ret;
+
+ /*
+ * The power down GPIO is optional. If present, toggle it from active to
+ * inactive to wake up the encoder.
+ */
+ adv7511->gpio_pd = devm_gpiod_get_optional(dev, "pd", GPIOD_OUT_HIGH);
+ if (IS_ERR(adv7511->gpio_pd))
+ return PTR_ERR(adv7511->gpio_pd);
+
+ if (adv7511->gpio_pd) {
+ mdelay(5);
+ gpiod_set_value_cansleep(adv7511->gpio_pd, 0);
+ }
+
+ adv7511->regmap = devm_regmap_init_i2c(i2c, &adv7511_regmap_config);
+ if (IS_ERR(adv7511->regmap))
+ return PTR_ERR(adv7511->regmap);
+
+ ret = regmap_read(adv7511->regmap, ADV7511_REG_CHIP_REVISION, &val);
+ if (ret)
+ return ret;
+ dev_dbg(dev, "Rev. %d\n", val);
+
+ ret = regmap_register_patch(adv7511->regmap, adv7511_fixed_registers,
+ ARRAY_SIZE(adv7511_fixed_registers));
+ if (ret)
+ return ret;
+
+ regmap_write(adv7511->regmap, ADV7511_REG_EDID_I2C_ADDR, edid_i2c_addr);
+ regmap_write(adv7511->regmap, ADV7511_REG_PACKET_I2C_ADDR,
+ packet_i2c_addr);
+ regmap_write(adv7511->regmap, ADV7511_REG_CEC_I2C_ADDR, cec_i2c_addr);
+ adv7511_packet_disable(adv7511, 0xffff);
+
+ adv7511->i2c_main = i2c;
+ adv7511->i2c_edid = i2c_new_dummy(i2c->adapter, edid_i2c_addr >> 1);
+ if (!adv7511->i2c_edid)
+ return -ENOMEM;
+
+ if (i2c->irq) {
+ init_waitqueue_head(&adv7511->wq);
+
+ ret = devm_request_threaded_irq(dev, i2c->irq, NULL,
+ adv7511_irq_handler,
+ IRQF_ONESHOT, dev_name(dev),
+ adv7511);
+ if (ret)
+ goto err_i2c_unregister_device;
+ }
+
+ /* CEC is unused for now */
+ regmap_write(adv7511->regmap, ADV7511_REG_CEC_CTRL,
+ ADV7511_CEC_CTRL_POWER_DOWN);
+
+ regmap_update_bits(adv7511->regmap, ADV7511_REG_POWER,
+ ADV7511_POWER_POWER_DOWN, ADV7511_POWER_POWER_DOWN);
+
+ adv7511->current_edid_segment = -1;
+
+ i2c_set_clientdata(i2c, adv7511);
+
+ adv7511_set_link_config(adv7511, &link_config);
+
+ return 0;
+
+err_i2c_unregister_device:
+ i2c_unregister_device(adv7511->i2c_edid);
+
+ return ret;
+}
+
+static int adv7511_remove(struct i2c_client *i2c)
+{
+ struct adv7511 *adv7511 = i2c_get_clientdata(i2c);
+
+ i2c_unregister_device(adv7511->i2c_edid);
+
+ kfree(adv7511->edid);
+
+ return 0;
+}
+
+static int adv7511_encoder_init(struct i2c_client *i2c, struct drm_device *dev,
+ struct drm_encoder_slave *encoder)
+{
+
+ struct adv7511 *adv7511 = i2c_get_clientdata(i2c);
+
+ encoder->slave_priv = adv7511;
+ encoder->slave_funcs = &adv7511_encoder_funcs;
+
+ adv7511->encoder = &encoder->base;
+
+ return 0;
+}
+
+static const struct i2c_device_id adv7511_i2c_ids[] = {
+ { "adv7511", 0 },
+ { "adv7511w", 0 },
+ { "adv7513", 0 },
+ { }
+};
+MODULE_DEVICE_TABLE(i2c, adv7511_i2c_ids);
+
+static const struct of_device_id adv7511_of_ids[] = {
+ { .compatible = "adi,adv7511", },
+ { .compatible = "adi,adv7511w", },
+ { .compatible = "adi,adv7513", },
+ { }
+};
+MODULE_DEVICE_TABLE(of, adv7511_of_ids);
+
+static struct drm_i2c_encoder_driver adv7511_driver = {
+ .i2c_driver = {
+ .driver = {
+ .name = "adv7511",
+ .of_match_table = adv7511_of_ids,
+ },
+ .id_table = adv7511_i2c_ids,
+ .probe = adv7511_probe,
+ .remove = adv7511_remove,
+ },
+
+ .encoder_init = adv7511_encoder_init,
+};
+
+static int __init adv7511_init(void)
+{
+ return drm_i2c_encoder_register(THIS_MODULE, &adv7511_driver);
+}
+module_init(adv7511_init);
+
+static void __exit adv7511_exit(void)
+{
+ drm_i2c_encoder_unregister(&adv7511_driver);
+}
+module_exit(adv7511_exit);
+
+MODULE_AUTHOR("Lars-Peter Clausen <lars@xxxxxxxxxx>");
+MODULE_DESCRIPTION("ADV7511 HDMI transmitter driver");
+MODULE_LICENSE("GPL");
diff --git a/drivers/gpu/drm/i2c/adv7511.h b/drivers/gpu/drm/i2c/adv7511.h
new file mode 100644
index 0000000..6599ed5
--- /dev/null
+++ b/drivers/gpu/drm/i2c/adv7511.h
@@ -0,0 +1,289 @@
+/*
+ * Analog Devices ADV7511 HDMI transmitter driver
+ *
+ * Copyright 2012 Analog Devices Inc.
+ *
+ * Licensed under the GPL-2.
+ */
+
+#ifndef __DRM_I2C_ADV7511_H__
+#define __DRM_I2C_ADV7511_H__
+
+#include <linux/hdmi.h>
+
+#define ADV7511_REG_CHIP_REVISION 0x00
+#define ADV7511_REG_N0 0x01
+#define ADV7511_REG_N1 0x02
+#define ADV7511_REG_N2 0x03
+#define ADV7511_REG_SPDIF_FREQ 0x04
+#define ADV7511_REG_CTS_AUTOMATIC1 0x05
+#define ADV7511_REG_CTS_AUTOMATIC2 0x06
+#define ADV7511_REG_CTS_MANUAL0 0x07
+#define ADV7511_REG_CTS_MANUAL1 0x08
+#define ADV7511_REG_CTS_MANUAL2 0x09
+#define ADV7511_REG_AUDIO_SOURCE 0x0a
+#define ADV7511_REG_AUDIO_CONFIG 0x0b
+#define ADV7511_REG_I2S_CONFIG 0x0c
+#define ADV7511_REG_I2S_WIDTH 0x0d
+#define ADV7511_REG_AUDIO_SUB_SRC0 0x0e
+#define ADV7511_REG_AUDIO_SUB_SRC1 0x0f
+#define ADV7511_REG_AUDIO_SUB_SRC2 0x10
+#define ADV7511_REG_AUDIO_SUB_SRC3 0x11
+#define ADV7511_REG_AUDIO_CFG1 0x12
+#define ADV7511_REG_AUDIO_CFG2 0x13
+#define ADV7511_REG_AUDIO_CFG3 0x14
+#define ADV7511_REG_I2C_FREQ_ID_CFG 0x15
+#define ADV7511_REG_VIDEO_INPUT_CFG1 0x16
+#define ADV7511_REG_CSC_UPPER(x) (0x18 + (x) * 2)
+#define ADV7511_REG_CSC_LOWER(x) (0x19 + (x) * 2)
+#define ADV7511_REG_SYNC_DECODER(x) (0x30 + (x))
+#define ADV7511_REG_DE_GENERATOR (0x35 + (x))
+#define ADV7511_REG_PIXEL_REPETITION 0x3b
+#define ADV7511_REG_VIC_MANUAL 0x3c
+#define ADV7511_REG_VIC_SEND 0x3d
+#define ADV7511_REG_VIC_DETECTED 0x3e
+#define ADV7511_REG_AUX_VIC_DETECTED 0x3f
+#define ADV7511_REG_PACKET_ENABLE0 0x40
+#define ADV7511_REG_POWER 0x41
+#define ADV7511_REG_STATUS 0x42
+#define ADV7511_REG_EDID_I2C_ADDR 0x43
+#define ADV7511_REG_PACKET_ENABLE1 0x44
+#define ADV7511_REG_PACKET_I2C_ADDR 0x45
+#define ADV7511_REG_DSD_ENABLE 0x46
+#define ADV7511_REG_VIDEO_INPUT_CFG2 0x48
+#define ADV7511_REG_INFOFRAME_UPDATE 0x4a
+#define ADV7511_REG_GC(x) (0x4b + (x)) /* 0x4b - 0x51 */
+#define ADV7511_REG_AVI_INFOFRAME_VERSION 0x52
+#define ADV7511_REG_AVI_INFOFRAME_LENGTH 0x53
+#define ADV7511_REG_AVI_INFOFRAME_CHECKSUM 0x54
+#define ADV7511_REG_AVI_INFOFRAME(x) (0x55 + (x)) /* 0x55 - 0x6f */
+#define ADV7511_REG_AUDIO_INFOFRAME_VERSION 0x70
+#define ADV7511_REG_AUDIO_INFOFRAME_LENGTH 0x71
+#define ADV7511_REG_AUDIO_INFOFRAME_CHECKSUM 0x72
+#define ADV7511_REG_AUDIO_INFOFRAME(x) (0x73 + (x)) /* 0x73 - 0x7c */
+#define ADV7511_REG_INT_ENABLE(x) (0x94 + (x))
+#define ADV7511_REG_INT(x) (0x96 + (x))
+#define ADV7511_REG_INPUT_CLK_DIV 0x9d
+#define ADV7511_REG_PLL_STATUS 0x9e
+#define ADV7511_REG_HDMI_POWER 0xa1
+#define ADV7511_REG_HDCP_HDMI_CFG 0xaf
+#define ADV7511_REG_AN(x) (0xb0 + (x)) /* 0xb0 - 0xb7 */
+#define ADV7511_REG_HDCP_STATUS 0xb8
+#define ADV7511_REG_BCAPS 0xbe
+#define ADV7511_REG_BKSV(x) (0xc0 + (x)) /* 0xc0 - 0xc3 */
+#define ADV7511_REG_EDID_SEGMENT 0xc4
+#define ADV7511_REG_DDC_STATUS 0xc8
+#define ADV7511_REG_EDID_READ_CTRL 0xc9
+#define ADV7511_REG_BSTATUS(x) (0xca + (x)) /* 0xca - 0xcb */
+#define ADV7511_REG_TIMING_GEN_SEQ 0xd0
+#define ADV7511_REG_POWER2 0xd6
+#define ADV7511_REG_HSYNC_PLACEMENT_MSB 0xfa
+
+#define ADV7511_REG_SYNC_ADJUSTMENT(x) (0xd7 + (x)) /* 0xd7 - 0xdc */
+#define ADV7511_REG_TMDS_CLOCK_INV 0xde
+#define ADV7511_REG_ARC_CTRL 0xdf
+#define ADV7511_REG_CEC_I2C_ADDR 0xe1
+#define ADV7511_REG_CEC_CTRL 0xe2
+#define ADV7511_REG_CHIP_ID_HIGH 0xf5
+#define ADV7511_REG_CHIP_ID_LOW 0xf6
+
+#define ADV7511_CSC_ENABLE BIT(7)
+#define ADV7511_CSC_UPDATE_MODE BIT(5)
+
+#define ADV7511_INT0_HDP BIT(7)
+#define ADV7511_INT0_VSYNC BIT(5)
+#define ADV7511_INT0_AUDIO_FIFO_FULL BIT(4)
+#define ADV7511_INT0_EDID_READY BIT(2)
+#define ADV7511_INT0_HDCP_AUTHENTICATED BIT(1)
+
+#define ADV7511_INT1_DDC_ERROR BIT(7)
+#define ADV7511_INT1_BKSV BIT(6)
+#define ADV7511_INT1_CEC_TX_READY BIT(5)
+#define ADV7511_INT1_CEC_TX_ARBIT_LOST BIT(4)
+#define ADV7511_INT1_CEC_TX_RETRY_TIMEOUT BIT(3)
+#define ADV7511_INT1_CEC_RX_READY3 BIT(2)
+#define ADV7511_INT1_CEC_RX_READY2 BIT(1)
+#define ADV7511_INT1_CEC_RX_READY1 BIT(0)
+
+#define ADV7511_ARC_CTRL_POWER_DOWN BIT(0)
+
+#define ADV7511_CEC_CTRL_POWER_DOWN BIT(0)
+
+#define ADV7511_POWER_POWER_DOWN BIT(6)
+
+#define ADV7511_HDMI_CFG_MODE_MASK 0x2
+#define ADV7511_HDMI_CFG_MODE_DVI 0x0
+#define ADV7511_HDMI_CFG_MODE_HDMI 0x2
+
+#define ADV7511_AUDIO_SELECT_I2C 0x0
+#define ADV7511_AUDIO_SELECT_SPDIF 0x1
+#define ADV7511_AUDIO_SELECT_DSD 0x2
+#define ADV7511_AUDIO_SELECT_HBR 0x3
+#define ADV7511_AUDIO_SELECT_DST 0x4
+
+#define ADV7511_I2S_SAMPLE_LEN_16 0x2
+#define ADV7511_I2S_SAMPLE_LEN_20 0x3
+#define ADV7511_I2S_SAMPLE_LEN_18 0x4
+#define ADV7511_I2S_SAMPLE_LEN_22 0x5
+#define ADV7511_I2S_SAMPLE_LEN_19 0x8
+#define ADV7511_I2S_SAMPLE_LEN_23 0x9
+#define ADV7511_I2S_SAMPLE_LEN_24 0xb
+#define ADV7511_I2S_SAMPLE_LEN_17 0xc
+#define ADV7511_I2S_SAMPLE_LEN_21 0xd
+
+#define ADV7511_SAMPLE_FREQ_44100 0x0
+#define ADV7511_SAMPLE_FREQ_48000 0x2
+#define ADV7511_SAMPLE_FREQ_32000 0x3
+#define ADV7511_SAMPLE_FREQ_88200 0x8
+#define ADV7511_SAMPLE_FREQ_96000 0xa
+#define ADV7511_SAMPLE_FREQ_176400 0xc
+#define ADV7511_SAMPLE_FREQ_192000 0xe
+
+#define ADV7511_STATUS_POWER_DOWN_POLARITY BIT(7)
+#define ADV7511_STATUS_HPD BIT(6)
+#define ADV7511_STATUS_MONITOR_SENSE BIT(5)
+#define ADV7511_STATUS_I2S_32BIT_MODE BIT(3)
+
+#define ADV7511_PACKET_ENABLE_N_CTS BIT(8+6)
+#define ADV7511_PACKET_ENABLE_AUDIO_SAMPLE BIT(8+5)
+#define ADV7511_PACKET_ENABLE_AVI_INFOFRAME BIT(8+4)
+#define ADV7511_PACKET_ENABLE_AUDIO_INFOFRAME BIT(8+3)
+#define ADV7511_PACKET_ENABLE_GC BIT(7)
+#define ADV7511_PACKET_ENABLE_SPD BIT(6)
+#define ADV7511_PACKET_ENABLE_MPEG BIT(5)
+#define ADV7511_PACKET_ENABLE_ACP BIT(4)
+#define ADV7511_PACKET_ENABLE_ISRC BIT(3)
+#define ADV7511_PACKET_ENABLE_GM BIT(2)
+#define ADV7511_PACKET_ENABLE_SPARE2 BIT(1)
+#define ADV7511_PACKET_ENABLE_SPARE1 BIT(0)
+
+#define ADV7511_REG_POWER2_HDP_SRC_MASK 0xc0
+#define ADV7511_REG_POWER2_HDP_SRC_BOTH 0x00
+#define ADV7511_REG_POWER2_HDP_SRC_HDP 0x40
+#define ADV7511_REG_POWER2_HDP_SRC_CEC 0x80
+#define ADV7511_REG_POWER2_HDP_SRC_NONE 0xc0
+#define ADV7511_REG_POWER2_TDMS_ENABLE BIT(4)
+#define ADV7511_REG_POWER2_GATE_INPUT_CLK BIT(0)
+
+#define ADV7511_LOW_REFRESH_RATE_NONE 0x0
+#define ADV7511_LOW_REFRESH_RATE_24HZ 0x1
+#define ADV7511_LOW_REFRESH_RATE_25HZ 0x2
+#define ADV7511_LOW_REFRESH_RATE_30HZ 0x3
+
+#define ADV7511_AUDIO_CFG3_LEN_MASK 0x0f
+#define ADV7511_I2C_FREQ_ID_CFG_RATE_MASK 0xf0
+
+#define ADV7511_AUDIO_SOURCE_I2S 0
+#define ADV7511_AUDIO_SOURCE_SPDIF 1
+
+#define ADV7511_I2S_FORMAT_I2S 0
+#define ADV7511_I2S_FORMAT_RIGHT_J 1
+#define ADV7511_I2S_FORMAT_LEFT_J 2
+
+#define ADV7511_PACKET(p, x) ((p) * 0x20 + (x))
+#define ADV7511_PACKET_SDP(x) ADV7511_PACKET(0, x)
+#define ADV7511_PACKET_MPEG(x) ADV7511_PACKET(1, x)
+#define ADV7511_PACKET_ACP(x) ADV7511_PACKET(2, x)
+#define ADV7511_PACKET_ISRC1(x) ADV7511_PACKET(3, x)
+#define ADV7511_PACKET_ISRC2(x) ADV7511_PACKET(4, x)
+#define ADV7511_PACKET_GM(x) ADV7511_PACKET(5, x)
+#define ADV7511_PACKET_SPARE(x) ADV7511_PACKET(6, x)
+
+enum adv7511_input_clock {
+ ADV7511_INPUT_CLOCK_1X,
+ ADV7511_INPUT_CLOCK_2X,
+ ADV7511_INPUT_CLOCK_DDR,
+};
+
+enum adv7511_input_justification {
+ ADV7511_INPUT_JUSTIFICATION_EVENLY = 0,
+ ADV7511_INPUT_JUSTIFICATION_RIGHT = 1,
+ ADV7511_INPUT_JUSTIFICATION_LEFT = 2,
+};
+
+enum adv7511_input_sync_pulse {
+ ADV7511_INPUT_SYNC_PULSE_DE = 0,
+ ADV7511_INPUT_SYNC_PULSE_HSYNC = 1,
+ ADV7511_INPUT_SYNC_PULSE_VSYNC = 2,
+ ADV7511_INPUT_SYNC_PULSE_NONE = 3,
+};
+
+/**
+ * enum adv7511_sync_polarity - Polarity for the input sync signals
+ * @ADV7511_SYNC_POLARITY_PASSTHROUGH: Sync polarity matches that of
+ * the currently configured mode.
+ * @ADV7511_SYNC_POLARITY_LOW: Sync polarity is low
+ * @ADV7511_SYNC_POLARITY_HIGH: Sync polarity is high
+ *
+ * If the polarity is set to either LOW or HIGH the driver will configure the
+ * ADV7511 to internally invert the sync signal if required to match the sync
+ * polarity setting for the currently selected output mode.
+ *
+ * If the polarity is set to PASSTHROUGH, the ADV7511 will route the signal
+ * unchanged. This is used when the upstream graphics core already generates
+ * the sync signals with the correct polarity.
+ */
+enum adv7511_sync_polarity {
+ ADV7511_SYNC_POLARITY_PASSTHROUGH,
+ ADV7511_SYNC_POLARITY_LOW,
+ ADV7511_SYNC_POLARITY_HIGH,
+};
+
+/**
+ * struct adv7511_link_config - Describes adv7511 hardware configuration
+ * @input_color_depth: Number of bits per color component (8, 10 or 12)
+ * @input_colorspace: The input colorspace (RGB, YUV444, YUV422)
+ * @input_clock: The input video clock style (1x, 2x, DDR)
+ * @input_style: The input component arrangement variant
+ * @input_justification: Video input format bit justification
+ * @clock_delay: Clock delay for the input clock (in ps)
+ * @embedded_sync: Video input uses BT.656-style embedded sync
+ * @sync_pulse: Select the sync pulse
+ * @vsync_polarity: vsync input signal configuration
+ * @hsync_polarity: hsync input signal configuration
+ */
+struct adv7511_link_config {
+ unsigned int input_color_depth;
+ enum hdmi_colorspace input_colorspace;
+ enum adv7511_input_clock input_clock;
+ unsigned int input_style;
+ enum adv7511_input_justification input_justification;
+
+ int clock_delay;
+
+ bool embedded_sync;
+ enum adv7511_input_sync_pulse sync_pulse;
+ enum adv7511_sync_polarity vsync_polarity;
+ enum adv7511_sync_polarity hsync_polarity;
+};
+
+/**
+ * enum adv7511_csc_scaling - Scaling factor for the ADV7511 CSC
+ * @ADV7511_CSC_SCALING_1: CSC results are not scaled
+ * @ADV7511_CSC_SCALING_2: CSC results are scaled by a factor of two
+ * @ADV7511_CSC_SCALING_4: CSC results are scalled by a factor of four
+ */
+enum adv7511_csc_scaling {
+ ADV7511_CSC_SCALING_1 = 0,
+ ADV7511_CSC_SCALING_2 = 1,
+ ADV7511_CSC_SCALING_4 = 2,
+};
+
+/**
+ * struct adv7511_video_config - Describes adv7511 hardware configuration
+ * @csc_enable: Whether to enable color space conversion
+ * @csc_scaling_factor: Color space conversion scaling factor
+ * @csc_coefficents: Color space conversion coefficents
+ * @hdmi_mode: Whether to use HDMI or DVI output mode
+ * @avi_infoframe: HDMI infoframe
+ */
+struct adv7511_video_config {
+ bool csc_enable;
+ enum adv7511_csc_scaling csc_scaling_factor;
+ const uint16_t *csc_coefficents;
+
+ bool hdmi_mode;
+ struct hdmi_avi_infoframe avi_infoframe;
+};
+
+#endif /* __DRM_I2C_ADV7511_H__ */
--
1.8.5.5
_______________________________________________
dri-devel mailing list
dri-devel@xxxxxxxxxxxxxxxxxxxxx
http://lists.freedesktop.org/mailman/listinfo/dri-devel
