[v3 10/13] drm/i915: Add 180 degree primary plane rotation support

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



From: Sonika Jindal <sonika.jindal@xxxxxxxxx>

Primary planes support 180 degree rotation. Expose the feature
through rotation drm property.

v2: Calculating linear/tiled offsets based on pipe source width and
height. Added 180 degree rotation support in ironlake_update_plane.

v3: Checking if CRTC is active before issueing update_plane. Added
wait for vblank to make sure we dont overtake page flips. Disabling
FBC since it does not work with rotated planes.

v4: Updated rotation checks for pending flips, fbc disable. Creating
rotation property only for Gen4 onwards. Property resetting as part
of lastclose.

v5: Resetting property in i915_driver_lastclose properly for planes
and crtcs. Fixed linear offset calculation that was off by 1 w.r.t
width in i9xx_update_plane and ironlake_update_plane. Removed tab
based indentation and unnecessary braces in intel_crtc_set_property
and intel_update_fbc. FBC and flip related checks should be done only
for valid crtcs.

v6: Minor nits in FBC disable checks for comments in intel_crtc_set_property
and positioning the disable code in intel_update_fbc.

v7: In case rotation property on inactive crtc is updated, we return
successfully printing debug log as crtc is inactive and only property change
is preserved.

v8: update_plane is changed to update_primary_plane, crtc->fb is changed to
crtc->primary->fb  and return value of update_primary_plane is ignored.

v9: added rotation property to primary plane instead of crtc. Removing reset
of rotation property from lastclose. rotation_property is moved to drm_plane,so
drm layer will take care of resetting.

v10: adding updation of fbc when rotation is set to 0.

v11: adding mutex locks for update_fbc. Allowing rotation only if value is
different than old one. Other minor cleanups.

Testcase: igt/kms_rotation_crc

Cc: dri-devel@xxxxxxxxxxxxxxxxxxxxx
Signed-off-by: Uma Shankar <uma.shankar@xxxxxxxxx>
Signed-off-by: Sagar Kamble <sagar.a.kamble@xxxxxxxxx>
Reviewed-by: Ville Syrjälä <ville.syrjala@xxxxxxxxxxxxxxx>
---
 drivers/gpu/drm/i915/i915_reg.h      |    1 +
 drivers/gpu/drm/i915/intel_display.c |  109 ++++++++++++++++++++++++++++++++--
 drivers/gpu/drm/i915/intel_pm.c      |    7 +++
 3 files changed, 112 insertions(+), 5 deletions(-)

diff --git a/drivers/gpu/drm/i915/i915_reg.h b/drivers/gpu/drm/i915/i915_reg.h
index c70c804..c600d3b 100644
--- a/drivers/gpu/drm/i915/i915_reg.h
+++ b/drivers/gpu/drm/i915/i915_reg.h
@@ -4087,6 +4087,7 @@ enum punit_power_well {
 #define   DISPPLANE_NO_LINE_DOUBLE		0
 #define   DISPPLANE_STEREO_POLARITY_FIRST	0
 #define   DISPPLANE_STEREO_POLARITY_SECOND	(1<<18)
+#define   DISPPLANE_ROTATE_180         (1<<15)
 #define   DISPPLANE_TRICKLE_FEED_DISABLE	(1<<14) /* Ironlake */
 #define   DISPPLANE_TILED			(1<<10)
 #define _DSPAADDR				0x70184
diff --git a/drivers/gpu/drm/i915/intel_display.c b/drivers/gpu/drm/i915/intel_display.c
index 5e8e711..47ef1c8 100644
--- a/drivers/gpu/drm/i915/intel_display.c
+++ b/drivers/gpu/drm/i915/intel_display.c
@@ -2414,7 +2414,9 @@ static void i9xx_update_primary_plane(struct drm_crtc *crtc,
 	unsigned long linear_offset;
 	u32 dspcntr;
 	u32 reg;
+	int pixel_size;
 
+	pixel_size = drm_format_plane_cpp(fb->pixel_format, 0);
 	intel_fb = to_intel_framebuffer(fb);
 	obj = intel_fb->obj;
 
@@ -2422,6 +2424,8 @@ static void i9xx_update_primary_plane(struct drm_crtc *crtc,
 	dspcntr = I915_READ(reg);
 	/* Mask out pixel format bits in case we change it */
 	dspcntr &= ~DISPPLANE_PIXFORMAT_MASK;
+	dspcntr &= ~DISPPLANE_ROTATE_180;
+
 	switch (fb->pixel_format) {
 	case DRM_FORMAT_C8:
 		dspcntr |= DISPPLANE_8BPP;
@@ -2463,8 +2467,6 @@ static void i9xx_update_primary_plane(struct drm_crtc *crtc,
 	if (IS_G4X(dev))
 		dspcntr |= DISPPLANE_TRICKLE_FEED_DISABLE;
 
-	I915_WRITE(reg, dspcntr);
-
 	linear_offset = y * fb->pitches[0] + x * (fb->bits_per_pixel / 8);
 
 	if (INTEL_INFO(dev)->gen >= 4) {
@@ -2477,6 +2479,18 @@ static void i9xx_update_primary_plane(struct drm_crtc *crtc,
 		intel_crtc->dspaddr_offset = linear_offset;
 	}
 
+	if (to_intel_plane(crtc->primary)->rotation == BIT(DRM_ROTATE_180)) {
+		dspcntr |= DISPPLANE_ROTATE_180;
+
+		x += (intel_crtc->config.pipe_src_w - 1);
+		y += (intel_crtc->config.pipe_src_h - 1);
+		linear_offset += (intel_crtc->config.pipe_src_h - 1) *
+			fb->pitches[0] +
+			(intel_crtc->config.pipe_src_w - 1) * pixel_size;
+	}
+
+	I915_WRITE(reg, dspcntr);
+
 	DRM_DEBUG_KMS("Writing base %08lX %08lX %d %d %d\n",
 		      i915_gem_obj_ggtt_offset(obj), linear_offset, x, y,
 		      fb->pitches[0]);
@@ -2487,7 +2501,8 @@ static void i9xx_update_primary_plane(struct drm_crtc *crtc,
 		I915_WRITE(DSPTILEOFF(plane), (y << 16) | x);
 		I915_WRITE(DSPLINOFF(plane), linear_offset);
 	} else
-		I915_WRITE(DSPADDR(plane), i915_gem_obj_ggtt_offset(obj) + linear_offset);
+		I915_WRITE(DSPADDR(plane), i915_gem_obj_ggtt_offset(obj) +
+				linear_offset);
 	POSTING_READ(reg);
 }
 
@@ -2504,7 +2519,9 @@ static void ironlake_update_primary_plane(struct drm_crtc *crtc,
 	unsigned long linear_offset;
 	u32 dspcntr;
 	u32 reg;
+	int pixel_size;
 
+	pixel_size = drm_format_plane_cpp(fb->pixel_format, 0);
 	intel_fb = to_intel_framebuffer(fb);
 	obj = intel_fb->obj;
 
@@ -2512,6 +2529,8 @@ static void ironlake_update_primary_plane(struct drm_crtc *crtc,
 	dspcntr = I915_READ(reg);
 	/* Mask out pixel format bits in case we change it */
 	dspcntr &= ~DISPPLANE_PIXFORMAT_MASK;
+	dspcntr &= ~DISPPLANE_ROTATE_180;
+
 	switch (fb->pixel_format) {
 	case DRM_FORMAT_C8:
 		dspcntr |= DISPPLANE_8BPP;
@@ -2549,8 +2568,6 @@ static void ironlake_update_primary_plane(struct drm_crtc *crtc,
 	else
 		dspcntr |= DISPPLANE_TRICKLE_FEED_DISABLE;
 
-	I915_WRITE(reg, dspcntr);
-
 	linear_offset = y * fb->pitches[0] + x * (fb->bits_per_pixel / 8);
 	intel_crtc->dspaddr_offset =
 		intel_gen4_compute_page_offset(&x, &y, obj->tiling_mode,
@@ -2558,6 +2575,21 @@ static void ironlake_update_primary_plane(struct drm_crtc *crtc,
 					       fb->pitches[0]);
 	linear_offset -= intel_crtc->dspaddr_offset;
 
+	if (to_intel_plane(crtc->primary)->rotation == BIT(DRM_ROTATE_180)) {
+		dspcntr |= DISPPLANE_ROTATE_180;
+
+		if (!IS_HASWELL(dev) && !IS_BROADWELL(dev)) {
+			x += (intel_crtc->config.pipe_src_w - 1);
+			y += (intel_crtc->config.pipe_src_h - 1);
+			linear_offset +=
+			(intel_crtc->config.pipe_src_h - 1) *
+			fb->pitches[0] + (intel_crtc->config.pipe_src_w - 1) *
+			pixel_size;
+		}
+	}
+
+	I915_WRITE(reg, dspcntr);
+
 	DRM_DEBUG_KMS("Writing base %08lX %08lX %d %d %d\n",
 		      i915_gem_obj_ggtt_offset(obj), linear_offset, x, y,
 		      fb->pitches[0]);
@@ -11324,10 +11356,64 @@ static void intel_plane_destroy(struct drm_plane *plane)
 	kfree(intel_plane);
 }
 
+static int intel_primary_plane_set_property(struct drm_plane *plane,
+				    struct drm_property *prop,
+				    uint64_t val)
+{
+	struct drm_device *dev = plane->dev;
+	struct drm_i915_private *dev_priv = dev->dev_private;
+	struct intel_plane *intel_plane = to_intel_plane(plane);
+	struct drm_crtc *crtc = plane->crtc;
+	struct intel_crtc *intel_crtc;
+	uint64_t old_val;
+
+	if (prop == plane->rotation_property) {
+		/* exactly one rotation angle please */
+		if (hweight32(val & 0xf) != 1)
+			return -EINVAL;
+
+		old_val = intel_plane->rotation;
+		intel_plane->rotation = val;
+
+		if (old_val == intel_plane->rotation)
+			return 0;
+
+		intel_crtc = to_intel_crtc(plane->crtc);
+
+		if (intel_crtc && intel_crtc->active && intel_crtc->primary_enabled) {
+			intel_crtc_wait_for_pending_flips(crtc);
+
+		/* FBC does not work on some platforms for rotated planes */
+			if (INTEL_INFO(dev)->gen <= 4 && !IS_G4X(dev)) {
+				if (dev_priv->fbc.plane == intel_crtc->plane &&
+					intel_plane->rotation != BIT(DRM_ROTATE_0))
+					intel_disable_fbc(dev);
+				/* If rotation was set earlier and new rotation is 0, we might
+				 * have disabled fbc earlier. So update it now */
+				else if (intel_plane->rotation == BIT(DRM_ROTATE_0) &&
+					old_val != BIT(DRM_ROTATE_0)) {
+					mutex_lock(&dev->struct_mutex);
+					intel_update_fbc(dev);
+					mutex_unlock(&dev->struct_mutex);
+				}
+			}
+
+			dev_priv->display.update_primary_plane(crtc,
+				crtc->primary->fb, 0, 0);
+
+		} else {
+			DRM_DEBUG_KMS("[CRTC:%d] is not active. Only rotation"
+				"property is updated\n", crtc->base.id);
+		}
+	}
+	return 0;
+}
+
 static const struct drm_plane_funcs intel_primary_plane_funcs = {
 	.update_plane = intel_primary_plane_setplane,
 	.disable_plane = intel_primary_plane_disable,
 	.destroy = intel_plane_destroy,
+	.set_property = intel_primary_plane_set_property
 };
 
 static struct drm_plane *intel_primary_plane_create(struct drm_device *dev,
@@ -11345,6 +11431,7 @@ static struct drm_plane *intel_primary_plane_create(struct drm_device *dev,
 	primary->max_downscale = 1;
 	primary->pipe = pipe;
 	primary->plane = pipe;
+	primary->rotation = BIT(DRM_ROTATE_0);
 	if (HAS_FBC(dev) && INTEL_INFO(dev)->gen < 4)
 		primary->plane = !pipe;
 
@@ -11360,6 +11447,18 @@ static struct drm_plane *intel_primary_plane_create(struct drm_device *dev,
 				 &intel_primary_plane_funcs,
 				 intel_primary_formats, num_formats,
 				 DRM_PLANE_TYPE_PRIMARY);
+	if (INTEL_INFO(dev)->gen >= 4) {
+		if (!primary->base.rotation_property)
+			primary->base.rotation_property =
+				drm_mode_create_rotation_property(dev,
+							BIT(DRM_ROTATE_0) |
+							BIT(DRM_ROTATE_180));
+		if (primary->base.rotation_property)
+			drm_object_attach_property(&primary->base.base,
+						primary->base.rotation_property,
+						primary->rotation);
+	}
+
 	return &primary->base;
 }
 
diff --git a/drivers/gpu/drm/i915/intel_pm.c b/drivers/gpu/drm/i915/intel_pm.c
index 2043c4b..bd6af91 100644
--- a/drivers/gpu/drm/i915/intel_pm.c
+++ b/drivers/gpu/drm/i915/intel_pm.c
@@ -562,6 +562,13 @@ void intel_update_fbc(struct drm_device *dev)
 		goto out_disable;
 	}
 
+	if (INTEL_INFO(dev)->gen <= 4 && !IS_G4X(dev) &&
+	    to_intel_plane(crtc->primary)->rotation != BIT(DRM_ROTATE_0)) {
+		if (set_no_fbc_reason(dev_priv, FBC_UNSUPPORTED_MODE))
+			DRM_DEBUG_KMS("Rotation unsupported, disabling\n");
+		goto out_disable;
+	}
+
 	/* If the kernel debugger is active, always disable compression */
 	if (in_dbg_master())
 		goto out_disable;
-- 
1.7.10.4

_______________________________________________
dri-devel mailing list
dri-devel@xxxxxxxxxxxxxxxxxxxxx
http://lists.freedesktop.org/mailman/listinfo/dri-devel





[Index of Archives]     [Linux DRI Users]     [Linux Intel Graphics]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]
  Powered by Linux