On Mon, 2014-06-09 at 02:41 +0000, YC Chen wrote: > Hi Benjamin, > After confirm with our h/w designer, ast2400 did not support > big-endian as you said. We support it in our previous product(PCI > revision < 0x20) for frame buffer access. So, the possible solution is > made in sw level for big-endian support. May we know the impact if we > did not support it in h/w design? We will consider to support it in > next generation. So the open power products are migrating toward mostly little endian environments where the problem is not present. But we still have a strong big endian legacy which would be nice to support. SW swapping is not a simple thing to do. A large part of the problem is that the X server (and the software stack above it mostly) have the native pixel format defined at compile time and is always BE on BE machines. So swapping requires hooks in various places and reduce performance. The two main cases are: - "Modern" distros such as fedora don't use the old style X DDX. They use the KMS Linux driver and the "modesetting" DDX which is unaccelerated and uses ShadowFB. We can add a swapping hook into there, but it will result in an even slower setup (and it's already pretty slow as it is). - The old DDX relies on the HW swapping. X will always draw in native format and since the old DDX draws directly into the FB, all non-accelerated accesses would have to be wrapped and swapped. It's even harder to do than the KMS case since it's not a single point that needs hooking and all fb ops must be wrapped. My recommendation here for future HW if you want to consider bringing BE support back in is to not swap at the PCIe interface level however. Leave that alone.. Simply provide a way to define the pixel format to be BE on the output pipe (CRTC) and 2D engine. IE. When the pixels are *consumed* from memory by the chip, not on the path between PCI and memory. PCIe-level swapping doesn't work well from experience, especially when manipulating objects of different bit depth in the same fb such as 32-bit pixmaps and 8-bit alpha masks. > The default MMIO is enabled since the products PCI revision >= 0x20. > The possible solution is check the value of 0x3c3 through MMIO. If the > value is 0xFF, then you must enable it through PCI IO. Will the value be 0xff because that's what the chip responds or will the chip not respond which *happens* to return 0xff on some x86 chipsets ? (ie, target abort). Because in the latter case, this will cause errors ranging from machine checks to EEH freeze on powerpc platforms. In fact, some x86 platforms are also configured to not ignore PCI errors and will fail in nasty ways with such a procedure. Can you confirm which specific bit of which register will enable MMIO ? What I can do is do that whenever IO space has been properly allocated (ie, is supported by the platform) and assume that MMIO is already enabled on platforms that don't support IO. Also, about the 0x380 difference in offset between IO and MMIO, is that always like that ? The documentation doesn't mention this at all... Cheers, Ben. > Regards, > > Y.C. Chen > > -----Original Message----- > From: Benjamin Herrenschmidt [mailto:benh@xxxxxxxxxxxxxxxxxxx] > Sent: Saturday, June 07, 2014 3:16 PM > To: Dave Airlie > Cc: dri-devel@xxxxxxxxxxxxxxxxxxxxx; YC Chen > Subject: Re: ast2400 woes > > On Sat, 2014-06-07 at 09:20 +1000, Benjamin Herrenschmidt wrote: > > > IE. Is there a reason why bASTIsVGAEnabled() and vASTEnableVGAMMIO > use > > the IO ports ? The latter reads 0x43 and writes 0x43 and 0x42, can > it > > be made to always use MMIO 0x3c3 and write 0x3c3 and 0x3c2 ? > > > > On my AST2400 at least, even when MMIO is disabled, 0x3c3 still > > responds so it works but is that valid for all chips ? Or do I need > to > > favor the PIO path if PIO is available in that case for older > chipsets > > ? > > Note: I have it working now with a couple of patches that i'll send > when I've cleaned them up, though I still need answers to the earlier > questions so we can make sure we don't break earlier chipset support > on x86. > > However, YC, the Endian control bits in extended CRTC register A2 seem > to have no effect at all. With a big endian kernel I get the wrong > endian on graphics regardless of the setting of that register ! > > Is endian swapping supported on the AST2400 ? > > Also what is the exact effect of that register ? Does it affect access > from PCI to the framebuffer or does it affect the way the CRTC > consumes pixels from the framebuffer ? Is is supposed to have an > effect on register accesses ? > > Cheers, > Ben. > > _______________________________________________ dri-devel mailing list dri-devel@xxxxxxxxxxxxxxxxxxxxx http://lists.freedesktop.org/mailman/listinfo/dri-devel
