Hi Andrzej,
Thank you for comments.
On 04/23/2014 06:02 PM, Andrzej Hajda wrote:
On 04/21/2014 02:28 PM, YoungJun Cho wrote:
This patch adds DT bindings for s6e3fa0 panel.
The bindings describes panel resources, display timings and cpu timings.
Changelog v2:
- Adds unit address (commented by Sachin Kamat)
Changelog v3:
- Removes optional delay, size properties (commented by Laurent Pinchart)
- Adds OLED detection, TE gpio properties
Changelog v4:
- Moves CPU timings relevant properties from FIMD DT
(commeted by Laurent Pinchart, Andrzej Hajda)
Signed-off-by: YoungJun Cho <yj44.cho@xxxxxxxxxxx>
Acked-by: Inki Dae <inki.dae@xxxxxxxxxxx>
Acked-by: Kyungmin Park <kyungmin.park@xxxxxxxxxxx>
---
.../devicetree/bindings/panel/samsung,s6e3fa0.txt | 63 ++++++++++++++++++++
1 file changed, 63 insertions(+)
create mode 100644 Documentation/devicetree/bindings/panel/samsung,s6e3fa0.txt
diff --git a/Documentation/devicetree/bindings/panel/samsung,s6e3fa0.txt b/Documentation/devicetree/bindings/panel/samsung,s6e3fa0.txt
new file mode 100644
index 0000000..9eeb38b
--- /dev/null
+++ b/Documentation/devicetree/bindings/panel/samsung,s6e3fa0.txt
@@ -0,0 +1,63 @@
+Samsung S6E3FA0 AMOLED LCD 5.7 inch panel
+
+Required properties:
+ - compatible: "samsung,s6e3fa0"
+ - reg: the virtual channel number of a DSI peripheral
+ - vdd3-supply: core voltage supply
+ - vci-supply: voltage supply for analog circuits
+ - reset-gpio: a GPIO spec for the reset pin
+ - det-gpio: a GPIO spec for the OLED detection pin
+ - te-gpio: a GPIO spec for the TE pin
+ - display-timings: timings for the connected panel as described by [1]
Which properties of display-timings are relevant for CPU mode?
I guess width and height. Anything more?
The CPU interface panel also requires hfront-porch, hback-porch,
hsync-len, vfront-porch, vback-porch and vsync-len.
+ - cpu-timings: CPU interface timings for the connected panel, and it contains
+ following optional properties.
+ - cs-setup: clock cycles for the active period of address signal
+ enable until chip select is enable in CPU interface
+ - wr-setup: clock cycles for the active period of CS signal enable
+ until write signal is enable in CPU interface
+ - wr-act: clock cycles for the active period of CS enable in CPU
+ interface
+ - wr-hold: clock cycles for the active period of CS disable until
+ write signal is disable in CPU interface
cpu-timings name does not sound to be related to display.
I wonder if it would not be better to merge cpu-timings into
display-timings but this will require more discussion I guess.
If you want to stay with separate node please consider to make it
optional as whole node or make some properties required. Making node
required with all sub-properties optional is weird.
Yes, I'll fix.
Thank you.
Best regards YJ
By the way I hope all timings properties are generic for CPU mode,
if not they should be prefixed by vendor or model.
Regards
Andrzej
+
+Optional properties:
+
+The device node can contain one 'port' child node with one child
+'endpoint' node, according to the bindings defined in [2]. This
+node should describe panel's video bus.
+
+[1]: Documentation/devicetree/bindings/video/display-timing.txt
+[2]: Documentation/devicetree/bindings/media/video-interfaces.txt
+
+Example:
+
+ panel@0 {
+ compatible = "samsung,s6e3fa0";
+ reg = <0>;
+ vdd3-supply = <&vcclcd_reg>;
+ vci-supply = <&vlcd_reg>;
+ reset-gpio = <&gpy7 4 0>;
+ det-gpio = <&gpg0 6 0>;
+ te-gpio = <&gpd1 7 0>;
+
+ display-timings {
+ timing0: timing-0 {
+ clock-frequency = <0>;
+ hactive = <1080>;
+ vactive = <1920>;
+ hfront-porch = <2>;
+ hback-porch = <2>;
+ hsync-len = <1>;
+ vfront-porch = <1>;
+ vback-porch = <4>;
+ vsync-len = <1>;
+ };
+ };
+
+ cpu-timings {
+ cs-setup = <0>;
+ wr-setup = <0>;
+ wr-act = <1>;
+ wr-hold = <0>;
+ };
+ };
_______________________________________________
dri-devel mailing list
dri-devel@xxxxxxxxxxxxxxxxxxxxx
http://lists.freedesktop.org/mailman/listinfo/dri-devel
