That comment wasn't super-readable, so I tried to improve it: - Put the comment before the values it's documenting - Add a mention to PRIME - Reword things a bit to be a lighter read - Add a note about the option to set the debug value at run-time Signed-off-by: Damien Lespiau <damien.lespiau@xxxxxxxxx> --- include/drm/drmP.h | 57 ++++++++++++++++++++++++++---------------------------- 1 file changed, 27 insertions(+), 30 deletions(-) diff --git a/include/drm/drmP.h b/include/drm/drmP.h index 3857450..97900b7 100644 --- a/include/drm/drmP.h +++ b/include/drm/drmP.h @@ -88,41 +88,38 @@ struct videomode; #include <drm/drm_hashtab.h> #include <drm/drm_mm.h> -#define DRM_UT_CORE 0x01 -#define DRM_UT_DRIVER 0x02 -#define DRM_UT_KMS 0x04 -#define DRM_UT_PRIME 0x08 /* - * Three debug levels are defined. - * drm_core, drm_driver, drm_kms - * drm_core level can be used in the generic drm code. For example: - * drm_ioctl, drm_mm, drm_memory - * The macro definition of DRM_DEBUG is used. - * DRM_DEBUG(fmt, args...) - * The debug info by using the DRM_DEBUG can be obtained by adding - * the boot option of "drm.debug=1". + * 4 debug categories are defined: + * + * CORE: Used in the generic drm code: drm_ioctl.c, drm_mm.c, drm_memory.c, ... + * This is the category used by the DRM_DEBUG() macro. + * + * DRIVER: Used in the vendor specific part of the driver: i915, radeon, ... + * This is the category used by the DRM_DEBUG_DRIVER() macro. * - * drm_driver level can be used in the specific drm driver. It is used - * to add the debug info related with the drm driver. For example: - * i915_drv, i915_dma, i915_gem, radeon_drv, - * The macro definition of DRM_DEBUG_DRIVER can be used. - * DRM_DEBUG_DRIVER(fmt, args...) - * The debug info by using the DRM_DEBUG_DRIVER can be obtained by - * adding the boot option of "drm.debug=0x02" + * KMS: used in the modesetting code. + * This is the category used by the DRM_DEBUG_KMS() macro. * - * drm_kms level can be used in the KMS code related with specific drm driver. - * It is used to add the debug info related with KMS mode. For example: - * the connector/crtc , - * The macro definition of DRM_DEBUG_KMS can be used. - * DRM_DEBUG_KMS(fmt, args...) - * The debug info by using the DRM_DEBUG_KMS can be obtained by - * adding the boot option of "drm.debug=0x04" + * PRIME: used in the prime code. + * This is the category used by the DRM_DEBUG_PRIME() macro. * - * If we add the boot option of "drm.debug=0x06", we can get the debug info by - * using the DRM_DEBUG_KMS and DRM_DEBUG_DRIVER. - * If we add the boot option of "drm.debug=0x05", we can get the debug info by - * using the DRM_DEBUG_KMS and DRM_DEBUG. + * Enabling verbose debug messages is done through the drm.debug parameter, + * each category being enabled by a bit. + * + * drm.debug=0x1 will enable CORE messages + * drm.debug=0x2 will enable DRIVER messages + * drm.debug=0x3 will enable CORE and DRIVER messages + * ... + * drm.debug=0xf will enable all messages + * + * An interesting feature is that it's possible to enable verbose logging at + * run-time by echoing the debug value in its sysfs node: + * # echo 0xf > /sys/module/drm/parameters/debug */ +#define DRM_UT_CORE 0x01 +#define DRM_UT_DRIVER 0x02 +#define DRM_UT_KMS 0x04 +#define DRM_UT_PRIME 0x08 extern __printf(4, 5) void drm_ut_debug_printk(unsigned int request_level, -- 1.8.3.1 _______________________________________________ dri-devel mailing list dri-devel@xxxxxxxxxxxxxxxxxxxxx http://lists.freedesktop.org/mailman/listinfo/dri-devel
