Am Dienstag, den 11.03.2014, 21:27 +0800 schrieb Shawn Guo:
> On Tue, Mar 11, 2014 at 12:42:08PM +0100, Philipp Zabel wrote:
> > Hi Shawn,
> >
> > Am Dienstag, den 11.03.2014, 11:46 +0800 schrieb Shawn Guo:
> > > On Wed, Mar 05, 2014 at 10:20:51AM +0100, Philipp Zabel wrote:
> > > > Hi,
> > > >
> > > > this latest version of the imx-drm DT binding patches applies
> > > > on top of staging-next and also depends on the OF graph binding
> > > > patchset that moves the v4l2_of helpers to drivers/of.
> > > > Currently, the two patchsets are also available at:
> > > > git://git.pengutronix.de/git/pza/linux.git topic/of-graph
> > > > git://git.pengutronix.de/git/pza/linux.git topic/imx-drm-dt
> > >
> > > Hi Philipp,
> > >
> > > I just came across a couple problems when testing the series on
> > > my imx6dl-sabresd board in dual display case - HDMI + LVDS. I tested it
> > > using Russell's branch below, which I believe has all the pieces put
> > > together.
> > >
> > > git://ftp.arm.linux.org.uk/~rmk/linux-arm.git imx-drm-staging
> > >
> > > - When I enable HDMI and LVDS support in both kernel build and device
> > > tree, HDMI seems working fine but LVDS color is corrupted quite badly.
> > >
> > > - When I enable HDMI and LVDS support in kernel build but only LVDS in
> > > device tree (keep HDMI disabled in device tree by not changing
> > > 'status' of HDMI node to 'okay'), LVDS does not even work. In this
> > > case, it seems that the binding of display-subsystem does not succeed.
> >
> > Can you check if you get the bound messages from
> > drivers/base/component.c:
> >
> > imx-drm display-subsystem.11: bound imx-ipuv3-crtc.0 (ops ipu_crtc_ops)
> > imx-drm display-subsystem.11: bound imx-ipuv3-crtc.1 (ops ipu_crtc_ops)
> > imx-drm display-subsystem.11: bound ldb.10 (ops imx_ldb_ops)
> >
> > I have tried this branch with a Phytec phyFLEX i.MX6S on PBAB01
> > baseboard with EDT 800x480 LVDS panel, and it seems to work.
> > The check in drivers/staging/imx-drm/imx-drm-core.c:675 should make sure
> > that unavailable (status="disabled") devices are just skipped.
>
> Sorry, Philipp. The setup in my report is incorrect. The correct setup
> to see this issue consists of:
>
> 1) build a kernel without HDMI support, i.e. !CONFIG_DRM_IMX_HDMI
>
> 2) enable HDMI device in DT, i.e. adding the lines below in board dts.
>
> &hdmi {
> status = "okay";
> };
>
> Sorry for the confusion.
>
This isn't a supported use-case, the componentized device stuff is there
exactly to ensure that the DRM device is only brought up after all
active components have an driver attached to them.
Regards,
Lucas
--
Pengutronix e.K. | Lucas Stach |
Industrial Linux Solutions | http://www.pengutronix.de/ |
Peiner Str. 6-8, 31137 Hildesheim, Germany | Phone: +49-5121-206917-5076 |
Amtsgericht Hildesheim, HRA 2686 | Fax: +49-5121-206917-5555 |
_______________________________________________
dri-devel mailing list
dri-devel@xxxxxxxxxxxxxxxxxxxxx
http://lists.freedesktop.org/mailman/listinfo/dri-devel
