Le 19/08/2024 à 23:49, Alex Lanzano a écrit :
Add support for the monochrome Sharp Memory LCDs.
Hi,
a few nitpick below, should thre be a v5.
...
+struct sharp_memory_device {
+ struct drm_device drm;
+ struct spi_device *spi;
+
+ const struct drm_display_mode *mode;
+
+ struct drm_crtc crtc;
+ struct drm_plane plane;
+ struct drm_encoder encoder;
+ struct drm_connector connector;
+
+ struct gpio_desc *enable_gpio;
+
+ struct task_struct *sw_vcom_signal;
+ struct pwm_device *pwm_vcom_signal;
+
+ enum sharp_memory_vcom_mode vcom_mode;
+ u8 vcom;
+
+ u32 pitch;
+ u32 tx_buffer_size;
+ u8 *tx_buffer;
+
+ /* When vcom_mode == "software" a kthread is used to
+ * periodically send a 'maintain display' message over
+ * spi. This mutex ensures tx_buffer access and spi bus
+ * usage is synchronized in this case
This comment could take only 3 lines and still be with < 80 lines.
A dot could also be added at the end of the 2nd sentence.
+ */
+ struct mutex tx_mutex;
+};
...
+static int sharp_memory_probe(struct spi_device *spi)
+{
+ int ret;
+ struct device *dev;
+ struct sharp_memory_device *smd;
+ struct drm_device *drm;
+ const char *vcom_mode_str;
+
+ ret = spi_setup(spi);
+ if (ret < 0)
+ return dev_err_probe(&spi->dev, ret, "Failed to setup spi device\n");
+
+ dev = &spi->dev;
If done earlier (when dev is declared?), it could already be used in the
dev_err_probe() just above?
+ if (!dev->coherent_dma_mask) {
+ ret = dma_coerce_mask_and_coherent(dev, DMA_BIT_MASK(32));
+ if (ret)
+ return dev_err_probe(dev, ret, "Failed to set dma mask\n");
+ }
+
+ smd = devm_drm_dev_alloc(dev, &sharp_memory_drm_driver,
+ struct sharp_memory_device, drm);
+ if (!smd)
+ return -ENOMEM;
+
+ spi_set_drvdata(spi, smd);
+
+ smd->spi = spi;
+ drm = &smd->drm;
+ ret = drmm_mode_config_init(drm);
+ if (ret)
+ return dev_err_probe(dev, ret, "Failed to initialize drm config\n");
+
+ smd->enable_gpio = devm_gpiod_get_optional(dev, "enable", GPIOD_OUT_HIGH);
+ if (!smd->enable_gpio)
+ dev_warn(dev, "Enable gpio not defined\n");
+
+ /*
+ * VCOM is a signal that prevents DC bias from being built up in
+ * the panel resulting in pixels being forever stuck in one state.
+ *
+ * This driver supports three different methods to generate this
+ * signal depending on EXTMODE pin:
+ *
+ * software (EXTMODE = L) - This mode uses a kthread to
+ * periodically send a "maintain display" message to the display,
+ * toggling the vcom bit on and off with each message
+ *
+ * external (EXTMODE = H) - This mode relies on an external
+ * clock to generate the signal on the EXTCOMM pin
+ *
+ * pwm (EXTMODE = H) - This mode uses a pwm device to generate
+ * the signal on the EXTCOMM pin
+ *
+ */
+ if (device_property_read_string(&spi->dev, "sharp,vcom-mode", &vcom_mode_str))
just dev?
+ return dev_err_probe(dev, -EINVAL,
+ "Unable to find sharp,vcom-mode node in device tree\n");
+
+ if (!strcmp("software", vcom_mode_str)) {
+ smd->vcom_mode = SHARP_MEMORY_SOFTWARE_VCOM;
+
+ } else if (!strcmp("external", vcom_mode_str)) {
+ smd->vcom_mode = SHARP_MEMORY_EXTERNAL_VCOM;
+
+ } else if (!strcmp("pwm", vcom_mode_str)) {
+ smd->vcom_mode = SHARP_MEMORY_PWM_VCOM;
+ ret = sharp_memory_init_pwm_vcom_signal(smd);
+ if (ret)
+ return dev_err_probe(dev, ret,
+ "Failed to initialize external COM signal\n");
+ } else {
+ return dev_err_probe(dev, -EINVAL, "Invalid value set for vcom-mode\n");
+ }
+
+ drm->mode_config.funcs = &sharp_memory_mode_config_funcs;
+ smd->mode = spi_get_device_match_data(spi);
+
+ smd->pitch = (SHARP_ADDR_PERIOD + smd->mode->hdisplay + SHARP_DUMMY_PERIOD) / 8;
+ smd->tx_buffer_size = (SHARP_MODE_PERIOD +
+ (SHARP_ADDR_PERIOD + (smd->mode->hdisplay) + SHARP_DUMMY_PERIOD) *
+ smd->mode->vdisplay) / 8;
+
+ smd->tx_buffer = devm_kzalloc(&spi->dev, smd->tx_buffer_size, GFP_KERNEL);
Just dev?
+ if (!smd->tx_buffer)
+ return -ENOMEM;
+
+ mutex_init(&smd->tx_mutex);
+
+ drm->mode_config.min_width = smd->mode->hdisplay;
+ drm->mode_config.max_width = smd->mode->hdisplay;
+ drm->mode_config.min_height = smd->mode->vdisplay;
+ drm->mode_config.max_height = smd->mode->vdisplay;
+
+ ret = sharp_memory_pipe_init(drm, smd, sharp_memory_formats,
+ ARRAY_SIZE(sharp_memory_formats),
+ NULL);
+ if (ret)
+ return dev_err_probe(dev, ret, "Failed to initialize display pipeline.\n");
+
+ drm_plane_enable_fb_damage_clips(&smd->plane);
+ drm_mode_config_reset(drm);
+
+ ret = drm_dev_register(drm, 0);
+ if (ret)
+ return dev_err_probe(dev, ret, "Failed to register drm device.\n");
+
+ drm_fbdev_dma_setup(drm, 0);
+
+ return 0;
+}
...
CJ
