Re: [PATCH v16 4/8] drm: bridge: Cadence: Add MHDP8501 DP/HDMI driver

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi,

There's still the scrambler issue we discussed on v15, but I have some
more comments.

On Tue, Jul 02, 2024 at 08:22:36PM GMT, Sandor Yu wrote:
> +enum drm_connector_status cdns_mhdp8501_detect(struct cdns_mhdp8501_device *mhdp)
> +{
> +	u8 hpd = 0xf;
> +
> +	hpd = cdns_mhdp8501_read_hpd(mhdp);
> +	if (hpd == 1)
> +		return connector_status_connected;
> +	else if (hpd == 0)
> +		return connector_status_disconnected;
> +
> +	dev_warn(mhdp->dev, "Unknown cable status, hdp=%u\n", hpd);
> +	return connector_status_unknown;
> +}
> +
> +static void hotplug_work_func(struct work_struct *work)
> +{
> +	struct cdns_mhdp8501_device *mhdp = container_of(work,
> +						     struct cdns_mhdp8501_device,
> +						     hotplug_work.work);
> +	enum drm_connector_status status = cdns_mhdp8501_detect(mhdp);
> +
> +	drm_bridge_hpd_notify(&mhdp->bridge, status);
> +
> +	if (status == connector_status_connected) {
> +		/* Cable connected  */
> +		DRM_INFO("HDMI/DP Cable Plug In\n");
> +		enable_irq(mhdp->irq[IRQ_OUT]);
> +	} else if (status == connector_status_disconnected) {
> +		/* Cable Disconnected  */
> +		DRM_INFO("HDMI/DP Cable Plug Out\n");
> +		enable_irq(mhdp->irq[IRQ_IN]);
> +	}
> +}

You shouldn't play with the interrupt being enabled here: hotplug
interrupts should always enabled.

If you can't for some reason, the reason should be documented in your
driver.

> +	/* Mailbox protect for HDMI PHY access */
> +	mutex_lock(&mhdp->mbox_mutex);
> +	ret = phy_init(mhdp->phy);
> +	mutex_unlock(&mhdp->mbox_mutex);
> +	if (ret) {
> +		dev_err(dev, "Failed to initialize PHY: %d\n", ret);
> +		goto clk_disable;
> +	}
> +
> +	/* Mailbox protect for HDMI PHY access */
> +	mutex_lock(&mhdp->mbox_mutex);
> +	ret = phy_set_mode(mhdp->phy, phy_mode);
> +	mutex_unlock(&mhdp->mbox_mutex);
> +	if (ret) {
> +		dev_err(dev, "Failed to configure PHY: %d\n", ret);
> +		goto clk_disable;
> +	}

Why do you need a shared mutex between the phy and HDMI controller?

> +static enum drm_mode_status
> +cdns_hdmi_tmds_char_rate_valid(const struct drm_bridge *bridge,
> +			       const struct drm_display_mode *mode,
> +			       unsigned long long tmds_rate)
> +{
> +	struct cdns_mhdp8501_device *mhdp = bridge->driver_private;
> +	union phy_configure_opts phy_cfg;
> +	int ret;
> +
> +	phy_cfg.hdmi.tmds_char_rate = tmds_rate;
> +
> +	/* Mailbox protect for HDMI PHY access */
> +	mutex_lock(&mhdp->mbox_mutex);
> +	ret = phy_validate(mhdp->phy, PHY_MODE_HDMI, 0, &phy_cfg);
> +	mutex_unlock(&mhdp->mbox_mutex);
> +	if (ret < 0)
> +		return MODE_CLOCK_RANGE;
> +
> +	return MODE_OK;
> +}
> +
> +static enum drm_mode_status
> +cdns_hdmi_bridge_mode_valid(struct drm_bridge *bridge,
> +			    const struct drm_display_info *info,
> +			    const struct drm_display_mode *mode)
> +{
> +	unsigned long long tmds_rate;
> +
> +	/* We don't support double-clocked and Interlaced modes */
> +	if (mode->flags & DRM_MODE_FLAG_DBLCLK ||
> +	    mode->flags & DRM_MODE_FLAG_INTERLACE)
> +		return MODE_BAD;
> +
> +	/* MAX support pixel clock rate 594MHz */
> +	if (mode->clock > 594000)
> +		return MODE_CLOCK_HIGH;

This needs to be in the tmds_char_rate_valid function

> +	if (mode->hdisplay > 3840)
> +		return MODE_BAD_HVALUE;
> +
> +	if (mode->vdisplay > 2160)
> +		return MODE_BAD_VVALUE;
> +
> +	tmds_rate = mode->clock * 1000ULL;
> +	return cdns_hdmi_tmds_char_rate_valid(bridge, mode, tmds_rate);

It will already be called by the core so this is redundant.

> +static void cdns_hdmi_bridge_atomic_enable(struct drm_bridge *bridge,
> +					   struct drm_bridge_state *old_state)
> +{
> +	struct cdns_mhdp8501_device *mhdp = bridge->driver_private;
> +	struct drm_atomic_state *state = old_state->base.state;
> +	struct drm_connector *connector;
> +	struct video_info *video = &mhdp->video_info;
> +	struct drm_crtc_state *crtc_state;
> +	struct drm_connector_state *conn_state;
> +	struct drm_display_mode *mode = &mhdp->mode;
> +	union phy_configure_opts phy_cfg;
> +	int ret;
> +
> +	connector = drm_atomic_get_new_connector_for_encoder(state,
> +							     bridge->encoder);
> +	if (WARN_ON(!connector))
> +		return;
> +
> +	mhdp->curr_conn = connector;
> +
> +	conn_state = drm_atomic_get_new_connector_state(state, connector);
> +	if (WARN_ON(!conn_state))
> +		return;
> +
> +	crtc_state = drm_atomic_get_new_crtc_state(state, conn_state->crtc);
> +	if (WARN_ON(!crtc_state))
> +		return;
> +
> +	video->color_fmt = conn_state->hdmi.output_format;
> +	video->bpc = conn_state->hdmi.output_bpc;
> +
> +	drm_mode_copy(&mhdp->mode, &crtc_state->adjusted_mode);

Why do you need a copy of all these fields? You should pass the
connector / bridge state around and not copy these fields.

> +	/* video mode check */
> +	if (mode->clock == 0 || mode->hdisplay == 0 || mode->vdisplay == 0)
> +		return;

This should be checked in atomic_check, but I'm pretty sure it's redundant.

> +	dev_dbg(mhdp->dev, "Mode: %dx%dp%d\n",
> +		mode->hdisplay, mode->vdisplay, mode->clock);
> +
> +	drm_atomic_helper_connector_hdmi_update_infoframes(connector, state);
> +
> +	/* Line swapping */
> +	cdns_mhdp_reg_write(&mhdp->base, LANES_CONFIG, 0x00400000 | mhdp->lane_mapping);
> +
> +	mhdp->hdmi.char_rate = drm_hdmi_compute_mode_clock(mode,
> +							   mhdp->video_info.bpc,
> +							   mhdp->video_info.color_fmt);

The TMDS char rate is already available in the connector_state so there
no need to recompute it.

> +	phy_cfg.hdmi.tmds_char_rate = mhdp->hdmi.char_rate;

And you shouldn't store a copy either.

> +	/* Mailbox protect for HDMI PHY access */
> +	mutex_lock(&mhdp->mbox_mutex);
> +	ret = phy_configure(mhdp->phy, &phy_cfg);
> +	mutex_unlock(&mhdp->mbox_mutex);
> +	if (ret) {
> +		dev_err(mhdp->dev, "%s: phy_configure() failed: %d\n",
> +			__func__, ret);
> +		return;
> +	}
> +
> +	cdns_hdmi_sink_config(mhdp);
> +
> +	ret = cdns_hdmi_ctrl_init(mhdp);
> +	if (ret < 0) {
> +		dev_err(mhdp->dev, "%s, ret = %d\n", __func__, ret);
> +		return;
> +	}
> +
> +	/* Config GCP */
> +	if (mhdp->video_info.bpc == 8)
> +		cdns_hdmi_disable_gcp(mhdp);
> +	else
> +		cdns_hdmi_enable_gcp(mhdp);
> +
> +	ret = cdns_hdmi_mode_config(mhdp, mode, &mhdp->video_info);
> +	if (ret < 0) {
> +		dev_err(mhdp->dev, "CDN_API_HDMITX_SetVic_blocking ret = %d\n", ret);
> +		return;
> +	}
> +}
> +
> +static int cdns_hdmi_bridge_clear_infoframe(struct drm_bridge *bridge,
> +					    enum hdmi_infoframe_type type)
> +{
> +	return 0;
> +}

Either implement it or don't, but an empty function is dead code.

> +static int cdns_hdmi_bridge_write_infoframe(struct drm_bridge *bridge,
> +					    enum hdmi_infoframe_type type,
> +					    const u8 *buffer, size_t len)
> +{
> +	struct cdns_mhdp8501_device *mhdp = bridge->driver_private;
> +
> +	switch (type) {
> +	case HDMI_INFOFRAME_TYPE_AVI:
> +		cdns_hdmi_config_infoframe(mhdp, 0, len, buffer, HDMI_INFOFRAME_TYPE_AVI);
> +		break;
> +	case HDMI_INFOFRAME_TYPE_SPD:
> +		cdns_hdmi_config_infoframe(mhdp, 1, len, buffer, HDMI_INFOFRAME_TYPE_SPD);
> +		break;
> +	case HDMI_INFOFRAME_TYPE_VENDOR:
> +		cdns_hdmi_config_infoframe(mhdp, 2, len, buffer, HDMI_INFOFRAME_TYPE_VENDOR);
> +		break;
> +	default:
> +		dev_dbg(mhdp->dev, "Unsupported infoframe type %x\n", type);
> +	}
> +
> +	return 0;
> +}
> +
> +static int cdns_hdmi_bridge_atomic_check(struct drm_bridge *bridge,
> +					 struct drm_bridge_state *bridge_state,
> +					 struct drm_crtc_state *crtc_state,
> +					 struct drm_connector_state *conn_state)
> +{
> +	return drm_atomic_helper_connector_hdmi_check(conn_state->connector, conn_state->state);
> +}

You should also call your mode_valid function here.

Maxime

Attachment: signature.asc
Description: PGP signature


[Index of Archives]     [Linux DRI Users]     [Linux Intel Graphics]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]
  Powered by Linux