[...]
>> +
>> +/**
>> + * enum adv7511_input_color_depth - Selects the input format color depth
>> + * @ADV7511_INPUT_COLOR_DEPTH_8BIT: Input format color depth is 8 bits per
> channel
>> + * @ADV7511_INPUT_COLOR_DEPTH_10BIT: Input format color dpeth is 10 bits
> per channel
>> + * @ADV7511_INPUT_COLOR_DEPTH_12BIT: Input format color depth is 12 bits
> per channel
>> + **/
>> +enum adv7511_input_color_depth {
>> + ADV7511_INPUT_COLOR_DEPTH_8BIT = 3,
>> + ADV7511_INPUT_COLOR_DEPTH_10BIT = 1,
>> + ADV7511_INPUT_COLOR_DEPTH_12BIT = 2,
>> +};
>
> Those enums describe the video format at the chip input. This can be
> configured statically from platform data or DT, but some platforms might need
> to setup formats dynamically at runtime. For instance the ADV7511 could be
> driven by a mux with two inputs using different formats.
>
> For these reasons I would combine all those enums in a single one that lists
> all possible input formats. The formats should be standardized and moved to a
> separate header file. Get and set format operations will be needed (this is
> something CDF will address :-)).
Since most these settings are orthogonal to each other putting them in one
enum gives you 3 * 3 * 6 * 3 = 162 entries. These enums configure to which
pins of the ADV7511 what signal is connected. Standardizing this would
require that other chips use the same layouts for connecting the pins.
[...]
>> +
>> +/**
>> + * enum adv7511_up_conversion - Selects the upscaling conversion method
>> + * @ADV7511_UP_CONVERSION_ZERO_ORDER: Use zero order up conversion
>> + * @ADV7511_UP_CONVERSION_FIRST_ORDER: Use first order up conversion
>> + *
>> + * This used when converting from a 4:2:2 format to a 4:4:4 format.
>> + **/
>> +enum adv7511_up_conversion {
>> + ADV7511_UP_CONVERSION_ZERO_ORDER = 0,
>> + ADV7511_UP_CONVERSION_FIRST_ORDER = 1,
>> +};
>
> How is the upscaling conversion method supposed to be selected ? What does it
> depend on ?
>
It's probably up to the system designer to say which method yields better
results for their system.
[...]
>> +/**
>> + * struct adv7511_video_config - Describes adv7511 hardware configuration
>> + * @csc_enable: Whether to enable color space conversion
>> + * @csc_scaling_factor: Color space conversion scaling factor
>> + * @csc_coefficents: Color space conversion coefficents
>> + * @hdmi_mode: Whether to use HDMI or DVI output mode
>> + * @avi_infoframe: HDMI infoframe
>> + **/
>> +struct adv7511_video_config {
>> + bool csc_enable;
>
> Shouldn't this be automatically computed based on the input and output formats
> ?
If the driver knew the input and output colorspaces and had coefficient
tables for all possible combinations built in that could be done. This is
maybe something that could be done in the framework.
>
>> + enum adv7511_csc_scaling csc_scaling_factor;
>> + const uint16_t *csc_coefficents;
>
> Do the coefficients need to be configured freely, or could presets do ?
>
>> + bool hdmi_mode;
>> + struct hdmi_avi_infoframe avi_infoframe;
>> +};
[...]
>> +static void adv7511_set_config(struct drm_encoder *encoder, void *c)
>
> Now we're getting to the controversial point.
>
> What bothers me about the DRM encoder slave API is that the display controller
> driver needs to be aware of the details of the slave encoder, as it needs to
> pass an encoder-specific configuration structure to the .set_config()
> operation. The question would thus be, what about using the Common Display
> Framework ?
Well, as I said I'd prefer using the CDF for this driver. But even then the
display controller driver might need to know about the details of the
encoder. I think we talked about this during the FOSDEM meeting. The
graphics fabric on the board can easily get complex enough to require a
board custom driver, similar to what we have in ASoC. I think this
drm_bridge patchset[1] tries to address a similar issue.
[1] http://lists.freedesktop.org/archives/dri-devel/2013-August/043237.html
[...]
>> +
>> + for (i = 0; i < 4; ++i) {
>> + ret = i2c_transfer(adv7511->i2c_edid->adapter, xfer,
> ARRAY_SIZE(xfer));
>> + if (ret < 0)
>> + return ret;
>> + else if (ret != 2)
>> + return -EIO;
>> +
>> + xfer[1].buf += 64;
>> + offset += 64;
>> + }
>
> Shouldn't you read two times 64 bytes per block, not four times ?
The controller on the ADV7511 always reads two blocks at once, so it is 256
bytes.
>
>> +
>> + adv7511->current_edid_segment = block / 2;
>> + }
>> +
>> + if (block % 2 == 0)
>> + memcpy(buf, adv7511->edid_buf, len);
>> + else
>> + memcpy(buf, adv7511->edid_buf + 128, len);
>> +
>> + return 0;
>> +}
>> +
[...]
>> +
>> +struct edid *adv7511_get_edid(struct drm_encoder *encoder)
>> +{
>> + struct adv7511 *adv7511 = encoder_to_adv7511(encoder);
>> +
>> + if (!adv7511->edid)
>> + return NULL;
>> +
>> + return kmemdup(adv7511->edid, sizeof(*adv7511->edid) +
>> + adv7511->edid->extensions * 128, GFP_KERNEL);
>> +}
>> +EXPORT_SYMBOL_GPL(adv7511_get_edid);
>
> Why do you need to export this function, who will use it ?
The drm driver using the encoder that wants to know the EDID. E.g. to know
if the monitor supports HDMI or not. But exporting this function is really
just a quick hack to compensate for the removal of 'raw_edid', this probably
wants proper abstraction in the framework.
[...]
>> +/*
>> + adi,input-id -
>> + 0x00:
>> + 0x01:
>> + 0x02:
>> + 0x03:
>> + 0x04:
>> + 0x05:
>> + adi,sync-pulse - Selects the sync pulse
>> + 0x00: Use the DE signal as sync pulse
>> + 0x01: Use the HSYNC signal as sync pulse
>> + 0x02: Use the VSYNC signal as sync pulse
>> + 0x03: No external sync pulse
>> + adi,bit-justification -
>> + 0x00: Evently
>> + 0x01: Right
>> + 0x02: Left
>> + adi,up-conversion -
>> + 0x00: zero-order up conversion
>> + 0x01: first-order up conversion
>> + adi,timing-generation-sequence -
>> + 0x00: Sync adjustment first, then DE generation
>> + 0x01: DE generation first then sync adjustment
>> + adi,vsync-polarity - Polarity of the vsync signal
>> + 0x00: Passthrough
>> + 0x01: Active low
>> + 0x02: Active high
>> + adi,hsync-polarity - Polarity of the hsync signal
>> + 0x00: Passthrough
>> + 0x01: Active low
>> + 0x02: Active high
>> + adi,reverse-bitorder - If set the bitorder is reveresed
>> + adi,tmds-clock-inversion - If set use tdms clock inversion
>> + adi,clock-delay - Clock delay for the video data clock
>> + 0x00: -1200 ps
>> + 0x01: -800 ps
>> + 0x02: -400 ps
>> + 0x03: no dealy
>> + 0x04: 400 ps
>> + 0x05: 800 ps
>> + 0x06: 1200 ps
>> + 0x07: 1600 ps
>
> The value should be expressed directly in ps in the DT.
DT doesn't allow negative values.
Thanks for the review,
- Lars
_______________________________________________
dri-devel mailing list
dri-devel@xxxxxxxxxxxxxxxxxxxxx
http://lists.freedesktop.org/mailman/listinfo/dri-devel
