In order to read the EDID from an eDP panel, you not only need to
power on the bridge chip itself but also the panel. In the ps8640
driver, this was made to work by having the bridge chip manually power
the panel on by calling pre_enable() on everything connectorward on
the bridge chain. This worked OK, but...
...when trying to do the same thing on ti-sn65dsi86, feedback was that
this wasn't a great idea. As a result, we designed the "DP AUX"
bus. With the design we ended up with the panel driver itself was in
charge of reading the EDID. The panel driver could power itself on and
the bridge chip was able to power itself on because it implemented the
DP AUX bus.
Despite the fact that we came up with a new scheme, implemented in on
ti-sn65dsi86, and even implemented it on parade-ps8640, we still kept
the old code around. This was because the new scheme required a DT
change. Previously the panel was a simple "platform_device" and in DT
at the top level. With the new design the panel needs to be listed in
DT under the DP controller node. The old code allowed us to properly
fetch EDIDs with ps8640 with the old DTs.
Unfortunately, the old code stopped working as of commit 102e80d1fa2c
("drm/bridge: ps8640: Use atomic variants of drm_bridge_funcs"). There
are cases at bootup where connector->state->state is NULL and the
kernel crashed at:
* drm_atomic_bridge_chain_pre_enable
* drm_atomic_get_old_bridge_state
* drm_atomic_get_old_private_obj_state
The crash went away at commit 4fb912e5e190 ("drm/bridge: Introduce
pre_enable_prev_first to alter bridge init order") which added a NULL
check. However, even though we were no longer crashing the end result
was that we weren't actually powering the panel on when we thought we
were. Things could end up working (despite warning splats) if
userspace was persistent and tried to get the mode again, but it
wasn't great.
A bit of digging was done to see if there was an easy fix but there
was nothing obvious. Instead, the only device using ps8640 the "old"
way had its DT updated so that the panel was no longer a simple
"platform_deice". See commit c2d94f72140a ("arm64: dts: mediatek:
mt8173-elm: Move display to ps8640 auxiliary bus") and commit
113b5cc06f44 ("arm64: dts: mediatek: mt8173-elm: remove panel model
number in DT").
Let's delete the old broken code so nobody gets tempted to copy it or
figure out how it works (since it doesn't).
NOTE: from a device tree "purist" point of view, we're supposed to
keep old device trees working and this patch is technically "against
policy". Reasons I'm still proposing it anyway:
1. Officially, old mt8173-elm device trees worked via the "little
white lie" approach. The DT would list an arbitrary/representative
panel that would be used for power sequencing. The mode information
in the panel driver would then be ignored / overridden by the EDID
reading code in ps8640. I don't feel too terrible breaking DTs that
contained the wrong "compatible" string to begin with. NOTE that
any old device trees that _didn't_ lie about their compatible will
still work because the mode information will come from the
hardcoded panels in panel-edp.
2. The only users of the old code were Chromebooks and Chromebooks
don't bake their DTs into the BIOS (they are bundled with the
kernel). Thus we don't need to worry about breaking someone using
an old DT with a new kernel.
3. The old code was broken anyway. If someone wants to fix the old
code instead of deleting it then they have my blessing, but without
a proper fix the old code isn't useful.
Reviewed-by: Sam Ravnborg <sam@xxxxxxxxxxxx>
Signed-off-by: Douglas Anderson <dianders@xxxxxxxxxxxx>
---
Changes in v2:
- Removed "Fixes" tag as per discussion on v1.
- Adjusted commit message since commit 4fb912e5e190 made things not crash.
drivers/gpu/drm/bridge/parade-ps8640.c | 79 --------------------------
1 file changed, 79 deletions(-)
diff --git a/drivers/gpu/drm/bridge/parade-ps8640.c b/drivers/gpu/drm/bridge/parade-ps8640.c
index 8801cdd033b5..8161b1a1a4b1 100644
--- a/drivers/gpu/drm/bridge/parade-ps8640.c
+++ b/drivers/gpu/drm/bridge/parade-ps8640.c
@@ -105,7 +105,6 @@ struct ps8640 {
struct gpio_desc *gpio_reset;
struct gpio_desc *gpio_powerdown;
struct device_link *link;
- struct edid *edid;
bool pre_enabled;
bool need_post_hpd_delay;
};
@@ -155,23 +154,6 @@ static inline struct ps8640 *aux_to_ps8640(struct drm_dp_aux *aux)
return container_of(aux, struct ps8640, aux);
}
-static bool ps8640_of_panel_on_aux_bus(struct device *dev)
-{
- struct device_node *bus, *panel;
-
- bus = of_get_child_by_name(dev->of_node, "aux-bus");
- if (!bus)
- return false;
-
- panel = of_get_child_by_name(bus, "panel");
- of_node_put(bus);
- if (!panel)
- return false;
- of_node_put(panel);
-
- return true;
-}
-
static int _ps8640_wait_hpd_asserted(struct ps8640 *ps_bridge, unsigned long wait_us)
{
struct regmap *map = ps_bridge->regmap[PAGE2_TOP_CNTL];
@@ -539,50 +521,6 @@ static void ps8640_bridge_detach(struct drm_bridge *bridge)
device_link_del(ps_bridge->link);
}
-static struct edid *ps8640_bridge_get_edid(struct drm_bridge *bridge,
- struct drm_connector *connector)
-{
- struct ps8640 *ps_bridge = bridge_to_ps8640(bridge);
- struct device *dev = &ps_bridge->page[PAGE0_DP_CNTL]->dev;
- bool poweroff = !ps_bridge->pre_enabled;
-
- if (!ps_bridge->edid) {
- /*
- * When we end calling get_edid() triggered by an ioctl, i.e
- *
- * drm_mode_getconnector (ioctl)
- * -> drm_helper_probe_single_connector_modes
- * -> drm_bridge_connector_get_modes
- * -> ps8640_bridge_get_edid
- *
- * We need to make sure that what we need is enabled before
- * reading EDID, for this chip, we need to do a full poweron,
- * otherwise it will fail.
- */
- if (poweroff)
- drm_atomic_bridge_chain_pre_enable(bridge,
- connector->state->state);
-
- ps_bridge->edid = drm_get_edid(connector,
- ps_bridge->page[PAGE0_DP_CNTL]->adapter);
-
- /*
- * If we call the get_edid() function without having enabled the
- * chip before, return the chip to its original power state.
- */
- if (poweroff)
- drm_atomic_bridge_chain_post_disable(bridge,
- connector->state->state);
- }
-
- if (!ps_bridge->edid) {
- dev_err(dev, "Failed to get EDID\n");
- return NULL;
- }
-
- return drm_edid_duplicate(ps_bridge->edid);
-}
-
static void ps8640_runtime_disable(void *data)
{
pm_runtime_dont_use_autosuspend(data);
@@ -592,7 +530,6 @@ static void ps8640_runtime_disable(void *data)
static const struct drm_bridge_funcs ps8640_bridge_funcs = {
.attach = ps8640_bridge_attach,
.detach = ps8640_bridge_detach,
- .get_edid = ps8640_bridge_get_edid,
.atomic_post_disable = ps8640_atomic_post_disable,
.atomic_pre_enable = ps8640_atomic_pre_enable,
.atomic_duplicate_state = drm_atomic_helper_bridge_duplicate_state,
@@ -705,14 +642,6 @@ static int ps8640_probe(struct i2c_client *client)
ps_bridge->bridge.of_node = dev->of_node;
ps_bridge->bridge.type = DRM_MODE_CONNECTOR_eDP;
- /*
- * In the device tree, if panel is listed under aux-bus of the bridge
- * node, panel driver should be able to retrieve EDID by itself using
- * aux-bus. So let's not set DRM_BRIDGE_OP_EDID here.
- */
- if (!ps8640_of_panel_on_aux_bus(&client->dev))
- ps_bridge->bridge.ops = DRM_BRIDGE_OP_EDID;
-
/*
* Get MIPI DSI resources early. These can return -EPROBE_DEFER so
* we want to get them out of the way sooner.
@@ -777,13 +706,6 @@ static int ps8640_probe(struct i2c_client *client)
return ret;
}
-static void ps8640_remove(struct i2c_client *client)
-{
- struct ps8640 *ps_bridge = i2c_get_clientdata(client);
-
- kfree(ps_bridge->edid);
-}
-
static const struct of_device_id ps8640_match[] = {
{ .compatible = "parade,ps8640" },
{ }
@@ -792,7 +714,6 @@ MODULE_DEVICE_TABLE(of, ps8640_match);
static struct i2c_driver ps8640_driver = {
.probe = ps8640_probe,
- .remove = ps8640_remove,
.driver = {
.name = "ps8640",
.of_match_table = ps8640_match,
--
2.41.0.162.gfafddb0af9-goog
