On ATSM the PL1 limit is disabled at power up. The previous uapi assumed that the PL1 limit is always enabled and therefore did not have a notion of a disabled PL1 limit. This results in erroneous PL1 limit values when the PL1 limit is disabled. For example at power up, the disabled ATSM PL1 limit was previously shown as 0 which means a low PL1 limit whereas the limit being disabled actually implies a high effective PL1 limit value. To get round this problem, the PL1 limit uapi is expanded to include a special value 0 to designate a disabled PL1 limit. A read value of 0 means that the PL1 power limit is disabled, writing 0 disables the limit. The link between this patch and the bugs mentioned below is as follows: * Because on ATSM the PL1 power limit is disabled on power up and there were no means to enable it, we previously implemented the means to enable the limit when the PL1 hwmon entry (power1_max) was written to. * Now there is a IGT igt@i915_hwmon@hwmon_write which (a) reads orig value from all hwmon sysfs (b) does a bunch of random writes and finally (c) restores the orig value read. On ATSM since the orig value is 0, when the IGT restores the 0 value, the PL1 limit is now enabled with a value of 0. * PL1 limit of 0 implies a low PL1 limit which causes GPU freq to fall to 100 MHz. This causes GuC FW load and several IGT's to start timing out and gives rise to these Intel CI bugs. After this patch, writing 0 would disable the PL1 limit instead of enabling it, avoiding the freq drop issue. v2: Add explanation for bugs mentioned below (Rodrigo) Link: https://gitlab.freedesktop.org/drm/intel/-/issues/8062 Link: https://gitlab.freedesktop.org/drm/intel/-/issues/8060 Signed-off-by: Ashutosh Dixit <ashutosh.dixit@xxxxxxxxx> Reviewed-by: Rodrigo Vivi <rodrigo.vivi@xxxxxxxxx> --- .../ABI/testing/sysfs-driver-intel-i915-hwmon | 4 +++- drivers/gpu/drm/i915/i915_hwmon.c | 24 +++++++++++++++++++ 2 files changed, 27 insertions(+), 1 deletion(-) diff --git a/Documentation/ABI/testing/sysfs-driver-intel-i915-hwmon b/Documentation/ABI/testing/sysfs-driver-intel-i915-hwmon index 2d6a472eef885..8d7d8f05f6cd0 100644 --- a/Documentation/ABI/testing/sysfs-driver-intel-i915-hwmon +++ b/Documentation/ABI/testing/sysfs-driver-intel-i915-hwmon @@ -14,7 +14,9 @@ Description: RW. Card reactive sustained (PL1/Tau) power limit in microwatts. The power controller will throttle the operating frequency if the power averaged over a window (typically seconds) - exceeds this limit. + exceeds this limit. A read value of 0 means that the PL1 + power limit is disabled, writing 0 disables the + limit. Writing values > 0 will enable the power limit. Only supported for particular Intel i915 graphics platforms. diff --git a/drivers/gpu/drm/i915/i915_hwmon.c b/drivers/gpu/drm/i915/i915_hwmon.c index 596dd2c070106..c099057888914 100644 --- a/drivers/gpu/drm/i915/i915_hwmon.c +++ b/drivers/gpu/drm/i915/i915_hwmon.c @@ -349,6 +349,8 @@ hwm_power_is_visible(const struct hwm_drvdata *ddat, u32 attr, int chan) } } +#define PL1_DISABLE 0 + /* * HW allows arbitrary PL1 limits to be set but silently clamps these values to * "typical but not guaranteed" min/max values in rg.pkg_power_sku. Follow the @@ -362,6 +364,14 @@ hwm_power_max_read(struct hwm_drvdata *ddat, long *val) intel_wakeref_t wakeref; u64 r, min, max; + /* Check if PL1 limit is disabled */ + with_intel_runtime_pm(ddat->uncore->rpm, wakeref) + r = intel_uncore_read(ddat->uncore, hwmon->rg.pkg_rapl_limit); + if (!(r & PKG_PWR_LIM_1_EN)) { + *val = PL1_DISABLE; + return 0; + } + *val = hwm_field_read_and_scale(ddat, hwmon->rg.pkg_rapl_limit, PKG_PWR_LIM_1, @@ -385,8 +395,22 @@ static int hwm_power_max_write(struct hwm_drvdata *ddat, long val) { struct i915_hwmon *hwmon = ddat->hwmon; + intel_wakeref_t wakeref; u32 nval; + if (val == PL1_DISABLE) { + /* Disable PL1 limit */ + hwm_locked_with_pm_intel_uncore_rmw(ddat, hwmon->rg.pkg_rapl_limit, + PKG_PWR_LIM_1_EN, 0); + + /* Verify, because PL1 limit cannot be disabled on all platforms */ + with_intel_runtime_pm(ddat->uncore->rpm, wakeref) + nval = intel_uncore_read(ddat->uncore, hwmon->rg.pkg_rapl_limit); + if (nval & PKG_PWR_LIM_1_EN) + return -EPERM; + return 0; + } + /* Computation in 64-bits to avoid overflow. Round to nearest. */ nval = DIV_ROUND_CLOSEST_ULL((u64)val << hwmon->scl_shift_power, SF_POWER); nval = PKG_PWR_LIM_1_EN | REG_FIELD_PREP(PKG_PWR_LIM_1, nval); -- 2.38.0
