Re: [PATCH v10 00/18] drm: Add Samsung MIPI DSIM bridge

[Date Prev][Date Next][Thread Prev][Thread Next][Date Index][Thread Index]

 



Hi Marek,

Am Sonntag, 18. Dezember 2022, 00:55:57 CET schrieb Marek Vasut:
> On 12/16/22 14:25, Alexander Stein wrote:
> Hi,
> 
> [...]
> 
> > Oh, nice, thanks for the pointer. When setting
> > 
> >> samsung,burst-clock-frequency = <668250000>;
> > 
> > in imx8mm.dtsi
> > I get a non-flickering display using 4 lanes. Although admittedly this is
> > just random guessing. I'm not sure which clock exactly has to be in the
> > range CHA_DSI_CLK_RANGE is configured to. With 4 lanes SN65DSI84 is
> > configured for> 
> > 205-210 MHz (0x29), while I get these PLL PMS settings on DSIM:
> >> samsung-dsim 32e10000.dsi: PLL freq 668250000, (p 4, m 99, s 0)
> >> samsung-dsim 32e10000.dsi: hs_clk = 668250000, byte_clk = 83531250,
> >> esc_clk
> > 
> > = 16706250
> 
> If I recall it right, minimum PLL frequency is:
> 
> fPMS=1.2*width*height*bpp*fps=1.2*800*480*24*60=663.5 MHz
> 
> the link frequency is then
> 
> fHS=fPMS/lanes/2=82.9 MHz (on the DDR clock lane)

Mh, there is something bogus about this. Right now the PLL freq is set 
depending on 'samsung,burst-clock-frequency' property. But this actually is 
somehow depending on the number of lanes I configure. From the debug output 
hs_clk and PLL freq are identical. AFAICS there is also no divider from PLL to 
hs_clk in the register map.

> So DSI83 should be in the range of 80..85 MHz input clock if I calculate
> this right. Can you check what is the value of mode->clock, the
> mipi_dsi_panel_format_to_bpp() return value, ctx->dsi->lanes in dsi83
> sm65dsi83_get_dsi_range() ?

A working setup on a tianma,tm070jvhg33 display (1280x800) is:
> samsung-dsim 32e10000.dsi: PLL freq 891000000, (p 3, m 99, s 0)
> samsung-dsim 32e10000.dsi: hs_clk = 891000000, byte_clk = 111375000, esc_clk 
= 18562500
> sn65dsi83 2-002d: mode->clock: 68200
> sn65dsi83 2-002d: mode bpp: 24
> sn65dsi83 2-002d: ctx->dsi->lanes: 3
> sn65dsi83 2-002d: samsung_dsim_set_pll: 0x37

Calculating backwards, sn64dsi83 is expecting a clock in the range of 275-280 
MHz. But I fail to see a corresponding clock in the DSIM PLL configuration.

Best regards,
Alexander

> > AFAICS DSIM bridge is configurung hs_clk, byte_clk and esc_clk just from
> > DT
> > properties, while SN65DSI84 is using display mode and number of lanes.
> > 
> > Is it expected that the DSIM PLL frequencies are set in DT for a specific
> > bridge/display setup?
> 
> No, there should be negotiation between the host and bridge/panel, I
> tried to propose two variants, but they were all rejected.







[Index of Archives]     [Linux DRI Users]     [Linux Intel Graphics]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Yosemite News]     [Linux Kernel]     [Linux SCSI]     [XFree86]     [Linux USB Devel]     [Video for Linux]     [Linux Audio Users]     [Linux Kernel]     [Linux SCSI]     [XFree86]
  Powered by Linux