[PATCH v1 7/7] drm/vc4: Make sure we don't end up with a core clock too high

[Maxime Ripard <maxime@xxxxxxxxxx>]

Following the clock rate range improvements to the clock framework,
trying to set a disjoint range on a clock will now result in an error.

Thus, we can't set a minimum rate higher than the maximum reported by
the firmware, or clk_set_min_rate() will fail.

Thus we need to clamp the rate we are about to ask for to the maximum
rate possible on that clock.

Signed-off-by: Maxime Ripard <maxime@xxxxxxxxxx>

diff --git a/drivers/gpu/drm/vc4/vc4_kms.c b/drivers/gpu/drm/vc4/vc4_kms.c
index b45dcdfd7306..4794e7235bb0 100644
--- a/drivers/gpu/drm/vc4/vc4_kms.c
+++ b/drivers/gpu/drm/vc4/vc4_kms.c
@@ -22,6 +22,8 @@
 #include <drm/drm_probe_helper.h>
 #include <drm/drm_vblank.h>
 
+#include <soc/bcm2835/raspberrypi-clocks.h>
+
 #include "vc4_drv.h"
 #include "vc4_regs.h"
 
@@ -354,6 +356,7 @@ static void vc4_atomic_commit_tail(struct drm_atomic_state *state)
 	struct vc4_hvs_state *new_hvs_state;
 	struct drm_crtc *crtc;
 	struct vc4_hvs_state *old_hvs_state;
+	unsigned long max_clock_rate;
 	unsigned int channel;
 	int i;
 
@@ -394,11 +397,12 @@ static void vc4_atomic_commit_tail(struct drm_atomic_state *state)
 		old_hvs_state->fifo_state[channel].pending_commit = NULL;
 	}
 
+	max_clock_rate = rpi_firmware_clk_get_max_rate(hvs->core_clk);
 	if (vc4->is_vc5) {
 		unsigned long state_rate = max(old_hvs_state->core_clock_rate,
 					       new_hvs_state->core_clock_rate);
-		unsigned long core_rate = max_t(unsigned long,
-						500000000, state_rate);
+		unsigned long core_rate = clamp_t(unsigned long, state_rate,
+						  500000000, max_clock_rate);
 
 		drm_dbg(dev, "Raising the core clock at %lu Hz\n", core_rate);
 
@@ -432,14 +436,17 @@ static void vc4_atomic_commit_tail(struct drm_atomic_state *state)
 	drm_atomic_helper_cleanup_planes(dev, state);
 
 	if (vc4->is_vc5) {
-		drm_dbg(dev, "Running the core clock at %lu Hz\n",
-			new_hvs_state->core_clock_rate);
+		unsigned long core_rate = min_t(unsigned long,
+					       max_clock_rate,
+					       new_hvs_state->core_clock_rate);
+
+		drm_dbg(dev, "Running the core clock at %lu Hz\n", core_rate);
 
 		/*
 		 * Request a clock rate based on the current HVS
 		 * requirements.
 		 */
-		WARN_ON(clk_set_min_rate(hvs->core_clk, new_hvs_state->core_clock_rate));
+		WARN_ON(clk_set_min_rate(hvs->core_clk, core_rate));
 
 		drm_dbg(dev, "Core clock actual rate: %lu Hz\n",
 			clk_get_rate(hvs->core_clk));

-- 
b4 0.10.0-dev-a76f5